NAVY MIL-C-60809 (2)-1978 CATAPULT AIRCRAFT EJECTION SEAT M9 REMANUFACTURED METAL PARTS ASSEMBLY《M9型飞机弹射座椅弹射器的再造金属组装部件》.pdf

上传人:bonesoil321 文档编号:977913 上传时间:2019-03-13 格式:PDF 页数:1 大小:64.94KB
下载 相关 举报
NAVY MIL-C-60809 (2)-1978 CATAPULT AIRCRAFT EJECTION SEAT M9 REMANUFACTURED METAL PARTS ASSEMBLY《M9型飞机弹射座椅弹射器的再造金属组装部件》.pdf_第1页
第1页 / 共1页
亲,该文档总共1页,全部预览完了,如果喜欢就下载吧!
资源描述

1、MiL-C-60 8 O 9 AMENDMENT 2 11 October 1978 SUPERSEDING AMENDMENT1 . 1 November 1976 MILITARY SPECIFICATION CATAPULT, AIRCRAFT EJECTION SEAT: M9 REMANUFACTURED METAL PARTS ASSEMBLY ,This amendment forms a part of Military Specification MIL-C-60809, dated 20 March 1969, and is approved for use by all

2、Departments and Agencies of the Department of Defense. PAGE 3 3.3, line 2: Delete “100 psi“ and substitute “90 psi“. PAGE 4 * Add: “3.8 Tensile load. The nozzle assembly shall withstand a tensile load of 4000 pounds, minimum, applied between retainer tang and nozzle along the horizontal axis of the

3、nozzle assembly without separation or deformation of the components.“ PAGE 15 * Add: “4.2.5 Tensile load. Each nozzle assembly shall be subjected to the tensile load test. Failure of any assembly to comply with the requirements of 3.8 shall be cause for rejection of the assembly.“ * Add: “4.3.4 Tens

4、ile load. The load designated in 3.8 shall be applied and shall register on the dial indicator calibrated to the applied load.“ * The margins of this amendment are marked with an asterisk to indicate where changes (additions, modifications, corrections, deletions) from the previous amendment were ma

5、de. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship

6、to the last previous amendment. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Station, Standardization Division (611), Indian Head, MD 20640 by using the self-addressed Standardization Documen

7、t Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. Commanding Officer, Naval Ordnance Custodian: Preparing Activity: Navy - OS Air Force - 99 Project No. 1377-0668 Navy - OS *O.S. GOVERNMENT PRINTING OFFICE: IS7-1224IASO THE DOGUMENT CBN?AlNS A PAGES, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

展开阅读全文
相关资源
猜你喜欢
  • EN ISO 15792-1-2008 en Welding consumables - Test methods - Part 1 Test methods for all-weld metal test specimens in steel nickel and nickel alloys (Incorporates Amendment A1 2011).pdf EN ISO 15792-1-2008 en Welding consumables - Test methods - Part 1 Test methods for all-weld metal test specimens in steel nickel and nickel alloys (Incorporates Amendment A1 2011).pdf
  • EN ISO 15792-2-2008 en Welding consumables - Test methods - Part 2 Preparation of single-run and two-run technique test specimens in steel《焊接消耗品 试验方法 第2部分 钢的单道和双道技术试样的制备[被代替 CEN EN.pdf EN ISO 15792-2-2008 en Welding consumables - Test methods - Part 2 Preparation of single-run and two-run technique test specimens in steel《焊接消耗品 试验方法 第2部分 钢的单道和双道技术试样的制备[被代替 CEN EN.pdf
  • EN ISO 15792-3-2011 en Welding consumables - Test methods - Part 3 Classification testing of positional capacity and root penetration of welding consumables in a fillet weld《焊接消耗品 .pdf EN ISO 15792-3-2011 en Welding consumables - Test methods - Part 3 Classification testing of positional capacity and root penetration of welding consumables in a fillet weld《焊接消耗品 .pdf
  • EN ISO 15796-2008 en Gas analysis - Investigation and treatment of analytical bias《气体分析 分析偏差的调查和处理》.pdf EN ISO 15796-2008 en Gas analysis - Investigation and treatment of analytical bias《气体分析 分析偏差的调查和处理》.pdf
  • EN ISO 15797-2004 en Textiles - Industrial washing and finishing procedures for testing of workwear《纺织材料 工作服检测用工业洗涤和整理规程 ISO 15797-2002》.pdf EN ISO 15797-2004 en Textiles - Industrial washing and finishing procedures for testing of workwear《纺织材料 工作服检测用工业洗涤和整理规程 ISO 15797-2002》.pdf
  • EN ISO 15797-2018 en Textiles - Industrial washing and finishing procedures for testing of workwear.pdf EN ISO 15797-2018 en Textiles - Industrial washing and finishing procedures for testing of workwear.pdf
  • EN ISO 15798-2013 en Ophthalmic implants - Ophthalmic viscosurgical devices - Amendment 1 (Incorporates Amendment A1 2017)《眼科植入物 黏弹性眼科植入装置》.pdf EN ISO 15798-2013 en Ophthalmic implants - Ophthalmic viscosurgical devices - Amendment 1 (Incorporates Amendment A1 2017)《眼科植入物 黏弹性眼科植入装置》.pdf
  • EN ISO 15831-2004 en Clothing - Physiological effects - Measurement of thermal insulation by means of a thermal manikin《服装 生理效应 热人体模型热绝缘的测量ISO 15831-2004》.pdf EN ISO 15831-2004 en Clothing - Physiological effects - Measurement of thermal insulation by means of a thermal manikin《服装 生理效应 热人体模型热绝缘的测量ISO 15831-2004》.pdf
  • EN ISO 15839-2006 en Water quality - On-line sensors analysing equipment for water - Specifications and performance tests《水质 水质测量在线传感器 分析设备 规范和性能试验》.pdf EN ISO 15839-2006 en Water quality - On-line sensors analysing equipment for water - Specifications and performance tests《水质 水质测量在线传感器 分析设备 规范和性能试验》.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1