1、AMSC N/A FSC 5935 INCH-POUND MIL-DTL-24231/8E(SH) 26 April 2013 SUPERSEDING MIL-C-24231/8D(SH) 15 May 1987 DETAIL SPECIFICATION SHEET CONNECTORS, SINGLE CABLE, TYPE III, SEVEN-CONDUCTOR This specification is approved for use by the Naval Sea Systems Command and is available for use by all Department
2、s and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-24231. REQUIREMENTS: 1. Dimensions and configuration: see figures 1 through 5. 2. Refer to MIL-DTL-24231/5 for alternate method of manufactur
3、ing connector body and installing guide pin M24231/5-071. 3. For welding of the pin, item 20, see MIL-DTL-24231/5. 4. Full or partial threads shall not extend more than 0.083 inch beyond the 1116-inch thread length. 5. All dimensions are in inches. 6. Tolerances shall be as follows, or as stated: a.
4、 Decimals 0.005 inch. b. Fractions 164 inch. c. Angular dimensions degree. 7. The flange outside diameter is intended to coincide with commonly available 2-inch bar stock. The dimension may vary after machine clean-up. 8. The gland nut shall be tightened until the packing tightens against the wires
5、and cables. This can be determined by moving the wires and cables gently back and forth until the wire and cable is seized by the packing. The gland nut shall be turned approximately one-fourth of a turn more to hold wires and cables in place. Do not overtighten the gland nut or attempt to tighten d
6、own metal to metal, as this can damage the wires and cables. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/8E(SH) 2 FIGURE 1. Connector, single cable, seven-conductor. ASSY, SIN GLECABLE CON NFOR T SS- 4 CA BLE, M24231 /8-0 01, SYM N
7、O. 51 7.8FOR F SS- 2 CA BLE, M24231 /8-0 02, SYM N O. 51 7.7FOR F SS- 4 CA BLE, M24231 /8-0 03, SYM N O. 51 7.9HARD NESS READING T O B E TAKEN AT T H ESE POIN T S.HARD NESS READING T O B E TAKEN AT T H IS F AC E AT120- DEGR EE INT ER VAL S.2CABLEMI24 231/8- 01 1ORM24 231/8- 01 2ORM24 231/8- 01 3NU T
8、 GLAND ,M24 231/6 -0 11 ,M24 231/9- 01 4WASH ER , SPRING LOC K,NAS M35 338- 12 4 ORM24 231/9- 01 3GASKET , O-R IN G,SAE- AS28 775- 32 7RING, G LA N D ,M24 231/6- 01 3OR M24 231/9- 01 2ASSY, S IN GLE CABLE C ONN ECT ORBODY , M242 31/8- 020 OR M24 23 1/9- 03 0ASSY, I N SER T , MOLD ED ,M24 231/8- 01
9、0GASKET , O-R IN G,SAE- AS28 775- 21 3RING, RETAININ GM24 231/7- 04 1GASKET , O-R IN G,SAE- AS28 775- 22 0CAP , M 24 231/13- 01 1NUT ,M24 231/5- 07 4RING, RETAININ GM24 231/5- 07 6WASH ER,M24 231/5- 07 5PAC KING,M24 231/6- 01 2OR M24 231/9- 01 1PIN,M24 231/5- 07 1SEE REQ T 2 AN D 3.GASKET , O-R IN G
10、SAE- AS28 775- 32 9SCREW ,M24 231/5- 08 3PLATE, ID EN TM24 231/8 -0 31 , M2 4231 / 8- 03 2,M24 231/8- 03 3I N SERT , NYL ON ,M24 231/5- 07 729221111282715161821923 2445717822123116121020131419FIGUR E 1 . C onne ctor , sev en- co nduc tor - M2 4231 /7-00 1, sy mbo l n o . 5 1 7 . 1 . 125Provided by
11、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/8E(SH) 3 18UNDERC U T.0.5300.50018*32*0.0510.041116R300.0670.0570.0270.023301.1891.1851.3021.292180.0660.0620.7860.77629322.2242.214323162-12U N- 2A1.2091.1991.4051.401321.6171.613234SEE N OTE 3* PI N
12、 WELD .* 0.0510.041R30132R327320.5050.4950.4420.432133215161582.2242.2145.8805.87072332630.120 H OL E,0.187 DE EP, DO N OTPENE T RAT E.+0.000-0.005125ALL OVE R EXCEP TAS SHOWN .6311161-12U NF- 2BSEE REQT. 4 .0.0720.0680.1900.1801.75 0-12 UN -2 A0.8970.8871.5551.5451.6301.6201.7501.7452.0051.995630.
13、0590.049RFIGURE 2. Asse mbly, single cable conduct or b ody - M24231/8-02 0(for M24231/8-001 a nd M24231/8-002 on ly) .FIGURE 2. Assembly, single cable connector body M24231/8-020 (for M24231/8-001 and M24231/8-002 only). Provided by IHSNot for ResaleNo reproduction or networking permitted without l
14、icense from IHS-,-,-MIL-DTL-24231/8E(SH) 4 0.0 520.0 50R964R0.1 38 - 32 N C - 2B, 2 HO LES, 316D EEP.( LOC ATE T O SUIT IDENTIFI CATI O N PLATE. )FIGU RE 3 . Ass embly, sin gle c able c onnect or b od y - M 24 23 1/ 8- 02 0 .FIGURE 3. Assembly, single cable connector body M24231/8-020. Provided by I
15、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/8E(SH) 5 0.0580.04838141332+132-13231615 FE E T0.9670.963MO LD ED E PO XY R ES IN1414132R116CA BL ER(TY P )1.1781.1681.5051.4950.0600.050527 28 2926CL12345670.2380.2280.1400.130CL0.2750.2651516PIN, CO
16、N T A C TFIGURE 4. Assembly, inse rt, molded - M 24 23 1/ 8- 01 0 .30FIGURE 4. Assembly, insert, molded M24231/8-010. 30 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/8E(SH) 6 FIGURE 5. Plate, identification M24231/8-031 (for M24231/8
17、001), M24231/8-032 (for M24231/8-002), M24231/8-033 (for M24231/8-003). FIGURE 5. Plat e, identifica tion - M24 231/8-031 (for M24231/8-001 ), M242 31/8-0 32(fo r M24231/ 8-002 ), M2423 1/8-033 (for M242 31/8-0 03) .60.156 , 2 HO LES51658CURRENT REV. L ETT ER ATTIME OF MANUFACT UR E.18H IGH LT RS (
18、M IN ).3163MANUF ACT URER SID ENTIFI CATIONHULL HOLE NO .REVM24 23 1/8-001, OR 8-002, OR 8- 00 3138R1166 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/8E(SH) 7 TABLE I. Parts list. Item no. 1/ Description 2/ Quantity for M24231/8- 3/
19、Material/specification Remarks 001 002 003 1 Connector assembly, single cable, symbol no. 517.8 1 - See figure 1. 2 Connector assembly, single cable, symbol no. 517.7 1 - See figure 1. 3 Connector assembly, single cable, symbol 517.9 1 - See figure 1. 4 Connector, body, single cable 1 1 Ni-Cu-Al, QQ
20、N-286 See figure 2 and figure 3 and requirement 2. 5 Epoxy resin, molded As required Cast epoxy resin compound 4/ See figure 4. 6 Plate, identification 1 1 1 CRES or Al, MIL-DTL-15024 See figure 5. 7 Gasket, O-ring 1 1 1 SAE-AS28775-213 5/ Lubricate with silicone compound SAE-AS8660, see figure 1.
21、8 Gasket, O-ring 1 1 1 SAE-AS28775-220 5/ See item 7. 9 Gasket, O-ring 1 1 1 SAE-AS28775-327 5/ See item 7. 10 Gasket, O-ring 1 1 1 SAE-AS28775-329 5/ See item 7. 11 Insert 1 1 1 M24231/5-077 See figure 1. 12 Screw 2 2 2 M24231/5-083 See figure 1. 13 Washer, body 1 1 1 M24231/5-075 See figure 1. 14
22、Nut, body 1 1 1 M24231/5-074 See figure 1. 15 Nut, gland 1 1 M24231/6-011 See figure 1. 16 Nut, gland 1 M24231/9-014 See figure 1. 17 Ring, retaining 1 1 1 M24231/7-041 See figure 1. 18 Ring, retaining 1 1 1 M24231/5-076 See figure 1. 19 Packing 1 1 M24231/6-012 See figure 1. 20 Pin, guide 1 1 1 M24
23、231/5-071 See requirement 2. 21 Washer, spring-lock 1 1 1 NASM35338-124 See figure 1. 22 Cap, pressure-proof 1 1 1 M24231/13-011 See figure 1. 23 Ring, gland 1 1 M24231/6-013 See figure 1. 24 Ring, gland 1 M24231/9-012 See figure 1. 25 Packing 1 M24231/9-011 See figure 1. 26 Pin, contact 7 7 7 MIL-D
24、TL-24231 See figure 4. 27 Cable, TSS-4, 15 1 MIL-DTL-915/8 See figure 1 and figure 4. 28 Cable, FSS-2, 15 1 MIL-DTL-915/8 See figure 1 and figure 4. 29 Cable, FSS-4, 15 1 MIL-DTL-915/8 See figure 1 and figure 4. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro
25、m IHS-,-,-MIL-DTL-24231/8E(SH) 8 TABLE I. Parts list Continued. Item no. 1/ Description 2/ Quantity for M24231/8- 3/ Material/Specification Remarks 001 002 003 30 Insert assembly, molded 1 1 1 See items 05, 26 and 27, 28, or 29 See figure 4. NOTES: 1/ Item numbers are the same as encircled numbers s
26、hown on figures. 2/ See applicable figure or table listed in remarks column for part numbers and dimensions. 3/ Quantity is for one complete assembly of each size. 4/ Arco Set 200, M.M. Reif and Co., Ivyland, PA, or PR610-TCF (Chockfast Orange), ITW Philadelphia Resins Corp., Montgomeryville, PA, or
27、 equal. 5/ Nitrile (Buna N); Parker Hannifin Corporation (part number N0756-75), O-ring Division, 2360 Palumbo Drive, Lexington, KY 40509, CAGE 02697, or equal. CHANGES FROM PREVIOUS ISSUE. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to
28、 the extent of the changes. Preparing activity: Navy SH (Project 5935-2011-057) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
