1、MIL-H-24299A 9999906 L98L300 493 I INCH- POUND MIL-H-24299A(SH) 5 AuRust 1994 SUPERSEDING 12 July 1967 (See 6.8) MIL-H-24299(SHIPS) MILITARY SPECIFICATION HEATERS, LUBRICATING OIL AND FUEL, ELECTRIC NAVAL SHIPBOARD This specification is approved for use by the Naval Sea Systems Command, Department o
2、f the Navy, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers heaters that are stationary, self- contained, and electrically operated. The heaters are used to heat lubricating oil or fuel for purification or warm-up.
3、1.2 Classification. Heaters are of the following types and styles as specified (see 6.2): Type A - Immersion heater Type B - Circulation heater Style 1 - Horizontal mount Style 2 - Vertical mount 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications. standards, and handbooks. The fo
4、llowing specifi- cations, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto,
5、cited in the solicitation (see 6.2). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, SEA 03R42, Naval Sea Systems Command, 2531 Jefferson Davis Hwy, Arlington, VA 22242-5160 by using
6、the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 4540 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted
7、 without license from IHS-,-,-MIL-H-24299A = 9999cSOb 1981301 32T SPEC I FI CAT IONS FEDERAL QQ-N-286 TT-P- 645 PPP - F- 3 20 MILITARY MIL-S-901 MIL-E-917 MIL-G-1149 MIL-S-1222 MIL-C-2212 MIL-L-9000 MIL-P-15024 MIL-E-15090 MIL-C-15726 MIL-T-16420 MIL-L-17331 MIL-E-17555 MIL-L-19140 MIL-S-19622 MIL-F
8、-20042 MIL-H-22577 MIL-S-22698 MIL-T-23648 MIL-L- 23699 MIL- T - 243 8 8 - Nickel-Copper-Aluminum Alloy, Wrought (UNS N05500). - Primer, Paint, Zinc-Molybdate, Alkyd Type. - Fiberboard; Corrugated and Solid, Sheet Stock (Container Grade), and Cut Shapes. - Shock Tests, H.I. (High-Impact) Shipboard M
9、achinery, Equipment, and Systems, Requirements for. - Electric Power Equipment, Basic Requirements (Naval Shipboard Use). - Gasket Materials, Synthetic Rubber, 50 and 65 Durometer Hardness. - Studs, Bolts, Hex Cap Screws, Socket Head Cap Screws and Nuts. - Contactors and Controllers, Electric Motor
10、AC or DC, and Associated Switching Devices. - Lubricating Oil, Shipboard Internal Combustion Engine, High Output Diesel. - Plates, Tags, and Bands for Identification of Equipment. - Enamel, Equipment, Light-Gray (Formula No. 111). - Copper-Nickel Alloy, Sheet, Plate, Strip, Bar, Rod and Wire. - Tube
11、, Copper-Nickel Alloy, Seamless and Welded (Copper Alloy Numbers 715 and 706). - Lubricating Oil, Steam Turbine and Gear, Moderate Service. - Electronic and Electrical Equipment, Accessories, and Provisioned Items (Repair Parts): Packaging of. - Lumber and Plywood, Fire-Retardant Treated. - Stuffing
12、 Tubes, Nylon; and Packing Assemblies; - Flanges, Pipe and Bulkhead, Bronze (Silver - Heating Elements, Electrical: Cartridge, Strip and - Steel Plate, Shapes and Bars, Weldable Ordinary - Resistor, Thermal, (Thermally Sensitive Resistor) - Lubricating Oil, Aircraft Turbine Engine, Synthetic - Therm
13、ocouple and Resistance Temperature Detector General Specification for. Brazing). Tubular Type. Strength and Higher Strength: Structural. Insulated, General Specification for. Base, NATO Code Number 0-156. Assemblies, General Specification for (Naval Shipboard). 2 Provided by IHSNot for ResaleNo repr
14、oduction or networking permitted without license from IHS-,-,-MIL-P-24691 - Pipe and Tube, Carbon, Alloy and Stainless Steel, MIL-P-24691/1 - Pipe and Tube, Carbon Steel, Seamless. MIL-G-24716 - Gaskets, Metallic-Flexible Graphite, Spiral Wound. MIL-R-83248 - Rubber Fluorocarbon Elastomer, High Temp
15、erature, MIL-R-83248/1 - Rubber, Fluorocarbon Elastomer, High Temperature, Seamless and Welded, General Specification for. Fluid and Compression Set Resistant. Fluid, and Compression Set Resistant, O-Rings, Class 1, 75 Hardness. Fluid, and Compression Set Resistant, O-Rings, Class 2, 90 Hardness. MI
16、L-R-83248/2 - Rubber, Fluorocarbon Elastomer, High Temperature, STANDARDS FEDERAL FED-STD-791 - Lubricants, Liquid Fuels, and Related Products; Methods of Testing. MILITARY MIL-STD-167-1 - Mechanical Vibrations of Shipboard Equipment (Type I - Environmental and Type II - Internally Excited). Compone
17、nt Parts. MIL-STD-202 - Test Methods for Electronic and Electrical MIL-STD-278 - Welding and Casting Standard. MIL-STD-454 - Standard General Requirements for Electronic Equipment. MIL-STD-769 - Thermal Insulation Requirements for Machinery and Piping. MIL-STD-1399 - Interface Standard for Shipboard
18、 Systems Section MS1579 5 - Washer, Flat-Metal, Round General Purpose. MS 16 18 7 - Stud, Continuous Thread (Bolt Stud), B16 Alloy Steel, High Temperature Service (875-1000F). MS17828 - Nut, Self-Locking, Hexagon, Regular-Height, (Non-Metallic Insert) 250F Nickel-Copper Alloy. MS 178 29 - Nut, Self-
19、Locking, Hexagon, Regular Height, 250“F, (Non-Metallic Insert) Non-Corrosion-Resistant Steel. (Non-Metallic Insert) CRES. Section 300 300 Electric Power, Alternating Current, (Metric) MS178 30 - Nut, Self-Locking, Hexagon, Regular Height, 250F MS1822 9 - Plug for “O“ Ring Gasket. MS21044 - Nut, Self
20、-Locking, Hexagon, Regular Height, 250“F, MS3 5 307 - Screw, Cap, Hexagon Head (Finished Hexagon Bolt), MS35311 - Screw, Cap, Hexagon Head-Nickel-Copper Alloy, Plain MS 3 5 649 - Nut, Plain, Hexagon, Machine Screw, UNC-2B. MS51412 - Washer, Flat (Round, Steel, General Purpose). MS5147 2 - Nut, Plain
21、, Hexagon, Carbon Steel, UNC-2B. 125 KSI FTM and 60 KSI FTM. Steel, Corrosion Resisting, Passivated, UNC-2A. Finish, UNC-2A. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-24299A 9999906 1981303 1T2 m MIL-H-24299A(SH) 2.2 Non-Government publ
22、ications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents no
23、t listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) B16.5 - Pipe Flanges and Flanged Fittings. MC96.1 - Temperature Measurement Thermocouples. (Application for copies should be addressed to the American National Sta
24、ndards Institute Inc., 11 West 42nd Street, New York, NY 10036.) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) A 167 - Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip. (DoD adopted) A 182 - Standard Specification for Forged or Rolled Alloy-St
25、eel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service. A 204 - Standard Specification for Pressure Vessel Plates, Alloy Steel, Molybdenum. (DoD adopted) A 312 - Standard Specification for Seamless and Welded Austenitic Stainless Steel Pipes. A 515 - Standard Specificat
26、ion for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service. (DoD adopted) A 516 - Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate and Lower-Temperature Service. (DoD adopted) Indicator Titration. (DoD adopted) D 974 - Standard Test Me
27、thod for Acid and Base Number by Color- (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute
28、the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document,
29、however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.5) in accordance with 4.3. 3.1.1 Operating fluid. fuel as specified (see 6.2)
30、. The heater will be used to heat lubricating oil or 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-H-24299A 9999906 L9L304 039 MIL-H-24299A(SH) 3.2 Materials. Materials shall be as specified in table I, table II, or table III as specified (s
31、ee 6.2). In cases where a choice of materials is given in the tables and a specific material is preferred, the acquisition requirements will so indicate. TABLE I. Ferrous materials. Part Shell and pipe connections Head and mounting plate Flanges for shell and pipe connections Plates and mounting lug
32、 Stay rods Plugs Studs Screws, bolts Nuts Nuts, self-locking Washers Material Tubing, seamless drawn carbon steel or Plate, welded, carbon- silicon steel, marine boiler quality Plate, carbon-silicon steel, marine boiler qual i ty Steel, carbon Plate, carbon-silicon steel, marine boiler qual i ty or
33、structural Plate, steel, carbon, Steel, carbon Steel, carbon Steel (grade B16) Steel (grade 5 or grade B16) Steel, carbon, zinc coated Steel, zinc plated Steel, carbon, zinc coated Applicable document MIL-P-24691, MIL-P-24691/1 ASTM A 515 ASTM A 516 ASTM A 204 ASTM A 515 ASTM A 516 ASTM A 204 ANSI B
34、16.5 ASTM A 515 ASTM A 516 ASTM A 204 MIL- 5 - 226 98 MIL-S-22698 MS18229 MS 16 187 MIL-S-1222 MS51472 MS17829, MS21044 MS5 1412 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-24297A 999990b 1983305 T75 MIL-H-24299A(SH) Part TABLE II. Nonfer
35、rous materials. Shell and pipe connections Head and mounting plate Flanges for shell and pipe connections I/ Plates and mounting lugs Stay rods S tuds Screws, bolts Nuts Nuts, self-locking Washers Plugs Mat er ia1 Copper-nickel alloy, cornposition 90-10 Copper-nickel alloy, composition 70-30 or Copp
36、er-nickel alloy Copper-nickel alloy Copper-nickel alloy Nickel-copper-aluminum alloy or Copper-nickel alloy, composition 70-30 Nickel-copper or Nickel-copper-aluminum Nickel-copper Nickel-copper-aluminum Nickel-copper Nickel-copper Nickel-copper Nickel-copper alloy Copper-nickel alloy or Applicable
37、document MIL-T-16420 MIL-C-15726 MIL-C-15726 MIL-C-15726 MIL-C-15726 QQ - N - 2 8 6 MIL-C-15726 MIL-S-1222 MIL-S-1222 MS35311 MIL-S-1222 MS35649 MS17 828 MS15 795 MS18 229 C/ Nonferrous flanges shall meet the dimensional requirements in accordance with MIL-F-20042. 6 Provided by IHSNot for ResaleNo
38、reproduction or networking permitted without license from IHS-,-,-MIL-H-24299A(SH) TABLE III. CRES materials. Part Shell and pipe connections Head and mounting plate Flanges for shell and heater and pipe connections Plates and mounting supports Stay rods Plugs Screws, bolts Nuts Nuts, self-locking M
39、a ter i al 304L or 316L 304L or 316L 304L or 316L Plate, carbon-silicon steel, marine boiler quality or Plate, steel carbon structural CRES CRES CRES CHRES (A286) CRES CHRES (A286) CRES App 1 ic ab 1 e document ASTM A 312 ASTM A 167 ASTM A 182 ASTM A 515 ASTM A 516 ASTM A 204 MIL-S-22698 ASTM A 312
40、MS 182 29 MS35307 MIL-S-1222 MS35649 MIL-S-1222 MS 17 830 3.2.1 Gaskets and stuffing tubes. The following materials shall be used for gaskets and stuffing tubes, as applicable (a) Metallic Flexible Graphite, Spiral Wound in accordance with (b) O-rings in accordance with MIL-R-83248 and MIL-R-83248/1
41、 (MIL-R-83248/2, 90 durometer for threaded bosses). (c) Synthetic rubber in accordance with MIL-G-1149, (d) Stuffing tubes, nylon in accordance with MIL-S-19622. MIL-G-24716 3.2.2 Recovered materials. Unless otherwise specified herein, all equipment, material, and articles incorporated in the produc
42、ts covered by this specification shall be new and may be fabricated using materials produced from recovered materials to the maximum extent practicable without jeopardizing the intended use. The term “recovered materials“ means materials which have been 7 Provided by IHSNot for ResaleNo reproduction
43、 or networking permitted without license from IHS-,-,-MIL-H-24299A 9999906 L98L307 848 W Fluid Lube oil Fuel, service Fuel, transfer collected or recovered from solid waste and reprocessed to become a source of raw materials, as opposed to virgin raw materials. interpreted to mean that the use of us
44、ed or rebuilt products is allowed under this specification unless otherwise specifically specified. None of the above shall be Type of heater Sheath material A CRES 304L or 316L B Steel A or B CRES 304L or 316L B Inconel 625 3.2.3 Prohibited materials. Asbestos, cadmium, and mercury shall not be use
45、d in the manufacture of the heaters or controls. In addition, zinc plating of parts to be immersed in oil is prohibited. 3.3 Construction. Construction shall be as specified in 3.3.1 through 3.3.15.9 (see 6.3). 3.3.1 Heating unit assembly. The heating unit assembly shall consist of a circular mounti
46、ng flange through which heater elements are inserted and welded to the plate at each penetration. The other end of the elements shall have spacers, or be braced between elements, for rigidity and shall have a means of support to the tank or heater shell. The unit shall be constructed to permit easy
47、removal of connected piping. Mounting flanges shall have threaded breakaway holes. These holes may also be used for inserting lifting eyebolts. All threaded fasteners to be immersed in the heated fluid shall be welded to prevent loosening. 3.3.2 Heater elements. Heater elements shall be type III tub
48、ular in accordance with MIL-H-22577 with seamless sheathing and ceramic-to-metal hermetic type end seals. Unless otherwise specified (see 6.2) sheath material shall be as Specified in table IV. Heating elements shall be bright annealed after all . fabrication steps up to insertion into the mounting
49、plate. 3.3.3 Terminal box. The electrical connections to the heater elements shall be enclosed in a watertight terminal box mounted on a flange and provided with a removable cover. A connection wiring diagram shall be glued to the underside of the terminal box cover. Holes for cable connections to the terminal box shall be provided as specified (see 6.2). Terminal connections shall be in accordance with MIL-STD-454. Electrical cree
