1、XIL-J-8 7 024 Amendment 1 4 May 1984 HILI .ARY S PEC IF IUT ION JACKET, INSEC REPELLENT nia amendment fome a part of Military Specification MIL-J-87024, dated 31 August 1976, and lo approved for use by all Departments and Agencies of the Department of Defense. Page 3 3.3.2 - Line 3, Delete “36 and 2
2、0“ and substitute “40 and 24“ 3.3.3 - End of sentence, delete period “(.I and add “, Type II, Green Shade 3046. Page 4 3.3.8 - Line 3, Delete “1-112 by 3 inches (3.8 by 7.6 cm)“ and substitute “1-1/4 by 2-114 inches“ Page 5 3.3.11 - Under “Caution“, line 1, delete “our“ and substitute “out“. Page 8
3、3.8 - Tabla I, operation 4b, add “or as an alternate, stitch together interlining and bottom edge of the sleeve using 515 or 519 or 516 stitch types; an SSA-2 seam; 8 to 1n stitches pes inch with a size B thread or the overedge stitch and size E for the chain stitch, The chain stitch shall be approx
4、imately 1/8 inch from the edge of the interlining.“ Page 10 Fable I, Operation 6d, line 2, delete “l/2 inch (12.7mm)“ and substitute “1 inch“. Operation 6e, delete in its entirety and substitute “e. Staystitch two plaits in the hood bottom, as indicated by marks on the pattern, folding each outside
5、edge toward6 the center seam of hood. I.E. with the bulk (on the inside of the hood) folded toward center“. ,es FSC 8415 c THIS DOCUMENT CONTAINS 2 PAGES. - .-.-. .- - .0 i Licensed by Information Handling ServicesMIL-5-87024 Amendment 1 . . .r Page 11 Table I, Operation 7a, add “or as an alternate,
6、 stitch a lqngth of 112 inch wide tape along the inside bottom edge of the jacket using 515, 516, or 519 stitch types; an SSA-2 seam; i3 to 10 stitches per inch with a size B thread for the overedge stitch, and size E for the chain stitch. The chain stitch shall be approximately 118 inch from the ed
7、ge of the tape.“ C Operation 7c, line 2 - after “fronts“ delete remainder of sentence and substitute “as indicated by marks on the interlining pattern and through all plies.“ Operation 7d, line 3 - delete “112 inch (12.7nan)“ and substitute “1 inch. “ Pag 12 Table I, Operation 9, delete in its entir
8、ety and substitute: “a. Attach five male snap fasteners to the right front closure as indicated by marks on the interlining pattern and through all plies. b. Attach five female snap fasteners to the left front closure as indicated by marks on the interlining pattern and-through all plies. C. Attach
9、two male and one female snap fastener to each of the sleeve bottoms as indicated by marks on the interlining pattern and through all plies. NOTE: The female snap fastener is secured on the sleeve bottom after folding as indicated by markings on the interlining pattern and through all plies“. 3.9 Tab
10、le II - Tolerance for sleeve, delete “plus or minus 1“. Also, under “front length, delete “22 (55.91, 23-1/2 (59.7) and 25 (63.5)“ and substitute “21-1/2, 23, and 24-1/2“ respectively. Custodian: Navy - Nu Review Activities: Navy - MS, CG DU-CT eer Activities: Navy - MC, AS, YD 2 of 2 Preparing Activity: Navy - Nu Project No, 8415-N391 Licensed by Information Handling Services
