1、I NOT MEASUREMENT i I SENSITIVE I MIL-L-23398D AMENDMENT 2 18 January 1994 SUPERSEDING AMENDMENT 1 24 SEPTEMBER 1990 MILITARY SPECIFICATION LUBRICANT, SOLID FILM, AIR-CURED, CORROSION INHIBITING, NATO CODE NUMBER S-749 This amendment forms a part of MIL-L-23398D, dated 20 November 1985, and is appro
2、ved for use by all Departments and Agencies of the Department of Defense. Page 1 2.1.1: Delete paragraph and substitute: “2.1.1 Specifications and standards. The following specifications and standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues
3、 of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISSI, and supplement thereto, cited in the sol ici tation (see 6.2) .II Page 2 *2.1.1: Under Specifications, Federal, add: “0-T-634 - Trichloroethylene, Technical“ *2.1.1: Under S
4、pecifications, Military, delete: “MIL-T-81533 - Trichloroethane, 1,1,1, (Methyl Chloroform) Inhibited, Vapor Degreas i ng“ 2.1.2: Under Code of Federal Regulations, delete “49 CFR - Transportation“, and substitute: “29 CFR 1910.1200 Occupational Safety and Health Standards-Hazard Communications 49 C
5、FR 171-178 Regulations for the Transportation of Hazardous Material S. II AMSC NIA FSC 9150 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 1 of 5 Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without l
6、icense from IHS-,-,-flIL-L-23398D (2) = YqqqqOb 1770863 396 AMENDMENT 2 MIL-L-233980 Page 2, conti nued 2.2: Delete first two sentences of paragraph and substitute the following: “2.2 Non-Government publications. The following documents form a part of this specification to the extent specified herei
7、n. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of the documents not listed in the DODISS are the issues of the documents cited in the sol ici tation (see 6.
8、21.“ 2.2: add the foLlowing reference document: “AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) ANSI 2129.1 American National Standard for the Precautionary Label i ng of Hazardous Industrial Chemicals (Application for copies should be addressed to the American National Standards Institute, Inc., 1430
9、 Broadway, New York, NY 10018).“ 2.2: Under AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM), delete “ASTM 0270 Sampling of Petroleum Products“, and substitute “ASTM D4057 Manual Sampl ing of Petroleum and Petroleum Products“. Page 3 3.2: last sentence, bottom of page, delete in its entirety, and s
10、ubstitute: “For Type II material, a non-fluorocarbon type, pressure producing agent, approved by the Environmental Protection Agency (PA), is required to expel the contents of the container, in accordance with the requirements of this specification.“ Page 4 3.2: delete last sentence of paragraph in
11、its entirety and substitute: “Both Type I and Type II material shall contain no graphi te, powdered metal, carbon black, charcoal or other forms of inorganic carbon (see 4.6.11.“ 2 Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without l
12、icense from IHS-,-,-Page 5 e 3.6: delete paragraph in its entirety and substitute: “3.6 Material safety data sheets. Material safety data sheets (MSDS) shall be prepared and submitted in accordance with FED-STD-313 and shall be ln accordance with the requirements of 29 CFR 1910.1200. When FED-STD-31
13、3 is at variance with the CFR, 29 CFR 1910.1200 shall take precedence, modify, and supplement FED-STD-313. One copy of the MSDS shall accompany the samples being submitted to the qualifying activity for testing (see 4.3.11.“ 4.1 delete paragraph in its entirety and substitute: “4.1 Responsibility fo
14、r inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own o
15、r any other facilities suitable for the performance of the inspection requirements specified herein, unless di sapproved by the Government. The Government reserves the right to perform any of the inspections set forth in thi s specification, where such inspections are deemed necessary to ensure supp
16、lies and services conform to prescribed requirements.“ e Add as new paragraph 4.1 .1: “4.1.1 Responsibility for compliance. All items must meet all reauirements of sections 3 and 5. The insDections set forth in this specification shall become a part of the contractors overall inspection system or qu
17、ality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of the
18、 manufacturing operation, is an acceptable practice to ascertain conformance to requirements; however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material .I Page 6 4.4.2: third line of paragraph,
19、delete “ASTM D270“ and substitute “ASTM 04057“. 3 Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 7 4.5.3: delete last sentence of paragraph in its entirety and substitute: “After application of the final
20、 coat, the coating shall be permitted to air-cure at ambient laboratory conditions (approximately 25C (77F) and approximately 50 percent relative humidity) for a period of 6 hours, prior to testing.“ 4.6.1: delete paragraph in its entirety and substitute: “4.6.1 Certification of compliance. Unless o
21、therwise specified, no material covered by this sPecification shall be submitted for acceptance under any contract or purchase order unti 1 certification and data have been approved by the procuring activi ty, ensuring conformance to 3.2 (see 6.61.“ Page 11 6.1: delete the first full sentence on pag
22、e, beginning with “This material.“, and substi tute: “This lubricant, although intended for air-cure application, may be heat-cured at temperatures up to 120C (248“F), for up to 1 hour after the coated work-piece has reached the desired temperature.“ 6.2.1: delete paragraph in its entirety and subst
23、itute: “6.2.1 Acquisition requirements. Acquisition documents should specify the fol lowing: a. b. C. d. e. f. g. h. Title, number, and date of this specification. Issue of DODISS to be cited in the solicitation and, if required, the specific issue of individual documents referenced (see 2.1 and 2.2
24、). Types and sizes required (see 1.2). Quantity required. Degree of preservation and packing required (see 5.1 and 5.2). Any special marking (see 5.3). Specify if palletization is required (see 5.4). Specify FAR Clauses 52.223-3.“ Page 12 Renumber paragraph 6.6 as paragraph 6.8. Add the following, a
25、s new paragraph 6.6: Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-i MIL-L-23390D (2) 9999906 1970866 OT5 MIL-L-23398D AMENDMENT 2 “6.6 Consideration of data requirements. The following data requirements sho
26、uld be considered when this soecification is applied on a contract. The applicable Data Item Description (DID) should be reviewed in conjunction with the specific acquisition to ensure that only essential data is requested/provided and that the DID is tailored to reflect the requirements of the spec
27、ific acquisition. To ensure correct contractual application of the data requirements, a Contract Data Requirements List (DD Form 1423) must be prepared to obtain the data, except where DoD FAR Supplement 27.475-1 exempts the requirement for a DD Form 1423. Reference paraqraph DID number DID title 4.
28、6.1 DI-NDTI-80809A Test/Insoection Reoorts (Para. 10.2.7 only) The above DID was cleared as of the date of this specification. The current issue of DoD 5010.12-L, Acquisition Management System and Data Requirements Control List (AMSDL), must be researched to ensure that only current, cleared DIDS ar
29、e cited on DD Form 1423.“ Add as new paragraph 6.7: “6.7 Subject term (keyword) listing. Corrosion preventative Fr ction reduction Material safety data sheet Qualified products li st (QPL)“ Page 15 *Table III, under fluid and specification: a. Delete: “Trichloroethane b. Add: “Trichloroethylene MIL-
30、T-81 533“ 0-T-634“ NOTE: The margins of this amendment are marked with asterisks to incicate where changes (additions, modifications, corrections, deletions) from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies
31、 in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Army - ME Navy - AS Air Force - 11 Preparing activity: Navy - AS Project No. 9150-1 11 6 Review activities: Army - AR, AV, MI, SM, AT Defense Nuclear Agency - DS 5 Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
