1、MILITARY SPECIFICATICN SHIFUS, WME“S: MATERNITY, KNG AM) SHORT SLEEVES fiis specification is approved for use by U.S. Marine Corps, Department of the Navy, and is available for use by all Departments and Agencies of the Departrent of Defense. 1. SCOPE . ?his specification covers the requirements for
2、 rnmens maternity shirts * =E wi long and short sleeves. 1.2 Classification. as ecified (see 6.2): The shirts shall be in the followinq types and sizes, Type I - Short Sleeve Type II - Iring Sleeve Schedule of Sizes Extra smll small Mediun Large 4- 6 8-1 O 12-1 4 16-1 8 2. APPLICABLE DommNTs 2.1 Gov
3、ernment documents. 2.1.1 cpe cifications and standards. n-ie follwing specifications and stan- dards form a part of this document to the extent specified herein. unless otherwise specified, the issues of these docunents are those listed in the issue of the Department of Defense Index of Specificatio
4、ns and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). Beneficial cannents (reccmmndations, additions, deletions) and any pertinent data which may be of use in improving this docurtent should be adresse to the Canmanding General (FSE-C) , Marine Corps Research, Devela
5、ipnent, and Acquisi- tion Camand, Washington, D.C. 20380, by using the self-addressed Standardiza- tion Document frrpravement Prmsal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8410 Distribution Statement - A. Approved for public release: distribution is unlimited
6、. 0 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-29388B 84 E 999998b O482438 O E MIG.S-29388a (MC) CPECIFIC4TICNC FEDERAL V-B-87 1 V-T-2 76 V-F2 8 5 “-I?-7 1 DWt2 O MILITARY MIL-P-15011 MIM-1 7757 MIGF-2 1840 MI GC-2 9 4 O 4 MG1L43548 MIGC-4
7、3594 MILrC-44296 FEDERAL FED-STD- 1 9 1 FDSTD-751 MILITAEJCY MIkSTW105 MIGSTP.129 MIGSTD-147 - Button, Sewing Hole and Button, Staple (Plastic) - Thread, Cotton - Thread, Polyester - Pallet, Material Handling, tribad, Stringer Construction, - Label, for Clothing, Elguipage an Tentage (General Use) 2
8、 Way and 4 Way (Partial) - Pallet, Material Handling, W, Post Construction, - Box, Shiping, Fiberboard (Wulai: Size) - Fastener, Tape, Hook and Pile, Synthetic - Cloth, Tropical, Falyester/kol - Thread, Polyester, Cotton-Covered and Rayon-bvered - Cloth Interlining, Polyester - Cloth, Fusibles 4 Way
9、 Entry - Textile Test Methods - Stitches, Sems and Stitchinqs - Sapling Procedures and Tables for Inspection by - Marking for Shipnent and Storage - Palletized Unit Lnad Attributes (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available frm
10、the Naval Publications and Fourrrs Center (Am: NPODS), 5801 Tar Avenue, Philadelphia, PA 19120-5099.) 2.1.2 Wer Governent docunents an publications. Ihe following other Gov- emnt documents and publications form a part of this docunent to the extent specified herein. Unless otherwise specified, the i
11、ssues are those cited in the solicitations. LAWS AND REGULATICHS u.S. Postal Service Manual (Application for copies of the manual may be obtained from the Cuperinten- dent of bcuments, U. S. Governrent Printing Office, Washington, D.C. 20402.) 2.2 Norr-Gatemment publications. The following document(
12、s) form a part of Unless otherwise specified, the this domment to the extent specified herein. 2 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- NIL-S-293E 84 M 999990b 0482439 2 M MIGS-29388B( MC) issues of the documents which are DoD adopted are
13、 those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the colicitation (see 6.2). NATICNAL WR FREIGHT TRAFFIC ASSOCIATION, INCI, AGENT National Wtor Freight Classificat
14、ion (Application for qies should be addressed to the American Trucking Associ- ation, Inc., Tariff Order Section, 1616 P. Street, N.W., Washington, D.C. 20036. ) UNIFRM CiASSIFICATION CQIMITTEE, AGENT Uniform Freight Classification (Application for copies should be addressed to the Uniform Classific
15、ation Cunmittee, mm 1106, 222 South Riverside Plaza; micago, IL 60606.) Department of Defense (DOD) Standard Shades for Buttons 1966 Department of kfense (DoD) Standard Color of Official Standardized Shades for Sewing n-ireads, 1968 (Application for copies should be addressed to the Color Acsociatio
16、n of the United States, Inc., 200 Madison Avenue, New York, NY 10016.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein (except for associated detail specifications, cpecification sheets or MS standards), the text of this docu- men
17、t takes precedence. Nothing in this docment, however, supersedes applica- ble laws and regulations unless a specific exertption has been obtained. 3. REQUIREMENTS 3.1 Standard sanples, Standard srniples, when furnished, are solely for guidance and information to the contractor (see 6.3). Variation f
18、ran this specification may appear in the standard sanple in which case the specifica- tion shall govern. 3.2 First article. When specified (see 6.2), a carple shall be subjected to first article inspection (see 6.4) in accordance with 4.4. 3.3 Materials 3.3.1 Basic material. %e basic material for th
19、e shirts shall be polyester/ wool, tropical khaki shade 2122, 6.3 to 6.8 ounce, conforming to type I of MIE-29404 . 3 3.2 Interlini The material used for interlining the front, callar Stand deafc of type I and II shirts and the cuffs of type II shirts shall be a nonwoven cloth interlining fusible. I
20、he fusible shall be a 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-293B 4 999990b 0482440 9 MIL+-293888 (MC) O 1.25 to 1.75 ounces per square yard, 80 to 85% polyester and 15 to 20% nylon with a thermal bonded polyester adhesive paste dot.
21、 %e fusing conditions shall be as follows: Tenperature 2 80 -290“ F Time 12-15 Sec 140-145“CE Pressure 4 to 6 PSI %e fusible interlining shall be Pillon S/8322 or equal. 3.3.3 niread, “he thread shall be cotton-covered polyester or polyester ticket N, 2 ply conforming to MGF43548 or V-W285. As an op
22、tion, thread conforming to type IA2 , ticket No. 40, 6 ply of V-T-276 may be used for the buttonholes. The thread shall be khaki shade P-1, cable No. 66019. (See DOD Standard Color Card of Official Standardized Shades for Sewing Thread 1968.) 3.3.4 Buttons. Ihe buttons shall be 19 line throughout co
23、nforming to type II, class K, style 25 of V+-871 tan shade AJ, Cable No. 62026. (See DOD Standard Shades for Buttons - 1966.) 3.3.5 Fastener pile tape. The nylon fastener loop tape to secure the neck- tab to the shirt shall be 5/8 inch wide x 3/4 inch long conforming to type I class 1 of MIGF-21840.
24、 The color of the fastener tape shall match the mate- rial of the shirt and conform to the colorfastness requirements specified in MIL-F-21840. 3.3.6 Labels. 3.3.6.1 Identification label. Each shirt shall have an identification label conforming to type vi, class 1 of ihLi-20. %e fastness to launderi
25、ng requirements of DDD-G20 shall apply. !he inscription shall be as follows: Nomenclature: Shirt, Wmns, Maternity Contract No.: DIA 100-00-0-00 (Exmie) Name of Contractor: 3.3.6.2 Instruction label, Each shirt shall have an instruction label con- !%e fastness to laundering require- forming to type V
26、I, class 3 of DDBGSO. ments of WD-L-20 shall apply. The inscription shall be as follows: LAUNDERMG INsTRUCTIms Launder in warn water using mild soap or detergent. Scrub soiled areas. IX) N(Tr BLEACH. Rinse thoroughly in clear, warn water. Do not squeeze or wring out. Place dripping shirt on hanger,
27、mess when dry or nearly dry on wrong side with stem iron on a low heat. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-29388B 4 W 9999906 0482441 O W MI L-S-2 9 388B ( MC ) a 3.3.6.3 ination label. As an alternate, a caribination identificat
28、ion and instruction label canfonninq to type VI, classes 1 arid 3 of DDG20 may be used. 3.3.6.4 Size label. VI, class 2 of: MID-T;!. shall apply. Each shirt shall have a size label conforming to type %e fastness to laundering requirements of DM)-G20 The inscription shall be as follows: Size 8R (Exmr
29、ple) Stock No. 8410-00-000-0000 (Exmle) 3.4 ksiqn. Tne shirts shall be the U.S. Marine Corps design shown on Figures 1 thrwh 4, seven button front and back yoke, shirred, front omanen- tal sleeve cuff (type I) and convertible collar. ?he type II shirt shall be on the same body design except with lon
30、g sleeves and cuff to button. Standard patterns will be furnished to the contractor by the Government. The standard patterns shall not be altered in any way and shall be used only as a guide for cutting the contractors wrking patterns. Ihe standard patterns provide 1/4 inch seam allowance for making
31、 the collar and 3/8 inch sean allowance for all other ceans except as otherwise specified in Table I. Standard patterns shcw size, sean allowance, directional lines for cutting and are marked or notched for proper placement and assembly of the conponent parts. 3.5.1 Pattern arts. The shirts shall be
32、 cut from the material specified 3.5 Patterns, herein in _$I_ acmr ance with the nunber of pattern parts indicated below: No. of Item Pattern Nomenclature Cut Parts Material: Basic 1. Front yoke 2 - 2. Front 3. Back yoke 4. Back 5. Sleeve-tyPe I 6. Sleeve-type II 7. Sleeve-Cuffs (type II) 8. Sleeve-
33、i3ining (type II) 9. Collar 10. Collarstand 2 11. Front 2 Material: interlining 12 * Collar 1 13. Collarstand 1 14. Sleeve-Cuffc (type II) 2 Marker 15. Front But tonhoe 5 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-5 MIL-S-293B 84 999990b 04824
34、42 2 -2 9388E (MC 3.6 Construction. The shirts chai1 be manufactured in accordance with the operations and stitch, sem, and stitching types specified in Table I. me contractor is not required to follm the exact sequence of operations as listed in Table I, but all operations shall be used to manufact
35、ure the shirts. The stitch, sean, and stitching types specified in Table I shall conform to FED-SW751. tiaienever ttm or more stitch or sean types are specified for the sane operation, any one of them may be used. ?he nunber of stitches per inch as specified in Table I indicates the minimum and maxi
36、mum nunber permitted. All overedge stitching shall be done on a serging machine with a knife attach- ment properly set to trim, not more than 1/8 inch, the raveled ee without cutting the material. When 517 stitch is used for the overedge stitch, it must be used throughout the shirt where given as an
37、 option. Ends of seam and stitching (stitch type 301), except the ends of a continuous line of stitch- ing, when not callght in another sean or stitching, shall be backtacked not less than 1/4 inch. me ends of a continuous line of stitching shall be mer- lapped not less than 1/2 inch. Thread breaks
38、(all stitch types) shall be secured by stitching back of the break not less than 1/2 inch. 3.6.1 Shade marki . The caponent parks of the shirt, except parts cut frcm ends +rked s a to ensure a uniform shade and size throughout the garment. Any mthcd of shade marking may be used except: (a) CUrrosive
39、 metal fastening devices. (b) Sew on tickets. (c) Adhesive type tickets which show discoloration and the adhesive mass which adheres to the material upon reiioval of the ticket, (d) Any marking mediun which muld tend to leave a permanent mark. NOTE: me use of ink pad numbering machine, rubber stamp,
40、 or pencil is al- lowed, provided the nunbering does not show on the outside of the garment and, wherever possible, is covered by the seam allowance. 3.6.2 Pressi All pressing oprations specified in Table I shall be accanplishe with a heated pressing iron or pressing machine set at medium (low) tenp
41、erature (285F maximum). 3.6.3 Fusing operations. All fusing of the fusible to the basic material shall be on a single ply basis (no stackinq allowed). The statement “fuse fusible to various cut parts in accordance with the manufacturers recomnenda- tion“ refers to time, tenperature, and pressure. 6
42、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-0 No - 1. 2. MIL-S-293BB 84 E 9999906 0482443 4 m MIL-S-29388B( MC) TABLE I MANUFACTURING REQUIREMENTS OPERATION htting. 3, Cut the shirt in strict sccordance with patterns fur- iished by the Government
43、. . Cut all materials in the rection indicated by direc- rional lines on the pattern. rhe straight of the material ;hall indicate the warp direc- :ion, 2. Cut the component parts Eor the shirt from one piece If basic material, except the Jnder collar, under ply col- Larstand and underply of cuffs na
44、y be cut from ends, but when zut from ends, the parts shall iarmonize with the shirt. The 3inding for the sleeve opening nay be strip-cut of sufficient #idth (1 5/8-inches) to finish 3/8 to 1/2-inch wide. Replacement of damaged parts . 1. Replace at time of cutting 3ny parts of the shirt con- tainin
45、g holes or serious weak- 3ning defects such a smashes, nultiple floats, loose or neakening slubs, etc., ex- ?ected to develop into holes, shade bars an dye streaks or unsightly slubc, etc. b. Replace any parts damaged 3uring the manufacturing pro- zess by needle chews which may ievelop into a hole,
46、scissor 3r knife cuts, tears, holes, mends or burns in the mate- rial. - STCH TYPE STCH/ IN NDL BOB/ LPR 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-29388B 84 m 9799906 0482444 b m MIL-S-29388B(MC) TABLE I MANUFACTURING QUIREMENTS OPEATi
47、ON ;hade marking . i. Mark or ticket all compo- ient parts (see 3.6.1) cut Srom one piece of basic mate- Yial, except those parts cut irom ends, to ensure uniform ;hade -and size throughout the shirt. Parts cut from ends ;hall be identified for size. rlake collar. Finished appearance. Th e 2ompleted
48、 collar shall finish smooth and flat without dis- tortion. Edges shall be uni- Eormly even. The seams shall Einich at the edges of the zollar. The points and seamed Idges shall be neatly and aompletely forced out. Th e points shall be uniform in lenqth. a. The collar and collarstand each shall be ma
49、de of two plies of basic material and one ply of fusible interlin- ing . b. Fuse collar interlining and topcollar stand together. c. Fuse collarstand interlin- ing and top collarstand to- gether. d. Position undercollar stand and undercollar face-to-face with top notches matching and edges even and seam together along top and side edges with 1/4-inch seam. e. Turn undercollar stand and stitch 1
