NC 26-107-1-1984 Drugs Levamisol Solution Quality Specifications《药物 “盐酸左旋咪唑”溶液 质量规格》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

DIN 26281-2010 de 5486 Rolling bearings - Methods for calculating the modified reference rating life for universally loaded bearings (ISO TS 16281 2008 + Cor 1 2009)《滚动轴承 普通负荷轴承用改良.pdf

DIN 263-1-2000 Single- and double-start acme thread with clearance for rail vehicles - Part 1 Dimensions《有轨车辆用带间隙的单头和双头爱克米螺纹 第1部分 尺寸》.pdf

DIN 263-3-2003 Single- and double-start acme thread with clearance for rail vehicles - Part 3 Thread gauges Thread dimensions and permissible wear of thread gauge《铁路车辆用带间隙的单头和双头爱克米.pdf

DIN 264-1-1973 Round Screw Thread with Clearance and Flat Flank with Pitch 7 mm Nominal Dimensions《螺距为 7mm 的带间隙和直侧面的圆螺纹 第1部分 公称尺寸》.pdf

DIN 264-2-1973 Round Screw Thread with Clearance and Flat Flank with Pitch 7 mm Limiting Dimensions of Screw Threads and Allowances Permissible Deviations and Permissible Wear of S.pdf

DIN 267-13-2007 Fasteners - Technical specifications - Part 13 Parts for bolted connections with specific mechanical properties for use at temperatures ranging from -200 C to +700 .pdf

DIN 267-2-2017 Fasteners - Technical specification surface roughness for product classes A and B《紧固件 A和B级产品的技术规格 表面粗糙度》.pdf

DIN 267-24-2007 Fasteners - Technical delivery conditions - Part 24 Hardness classes for nuts without specified proof load values《紧固件 交货技术条件 第24部分 不带规定验证载荷值的螺母用硬度等级》.pdf

DIN 267-26-2005 Fasteners - Technical specifications - Part 26 Conical spring washers for bolted connections《紧固件 技术规范 第26部分 螺栓连接件用锥形弹簧垫圈》.pdf