NC 97-20-1987 Packing and Packaging Aluminum Tubes Terms and Definitions《包装 铝管术语和定义》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

AGMA 10FTM07-2010 A New Statistical Model for Predicting Tooth Engagement and Load Sharing in Involute Splines《预测渐开线花键齿轮齿啮合和负载共享的一种新统计模型》.pdf

AGMA 10FTM08-2010 Calculation of Load Distribution in Planetary Gears for an Effective Gear Design Process《计算行星齿轮的载荷分布 以获有效的齿轮设计过程》.pdf

AGMA 10FTM09-2010 Reverse Engineering《逆向工程》.pdf

AGMA 10FTM10-2010 Evaluation of Methods for Calculating Effects of Tip Relief on Transmission Error Noise and Stress in Loaded Spur Gears《直齿轮传动误差 噪声和应力修根影响的计算评价方法》.pdf

AGMA 10FTM11-2010 Point-Surface-Origin PSO Macropitting Caused by Geometric Stress Concentration GSC《几何应力集中(GSC)形成的点-面-原点(PSO).粗点》.pdf

AGMA 10FTM12-2010 Flank Load Carrying Capacity and Power Loss Reduction by Minimized Lubrication《通过最小润滑减少侧面承载能力和功率损耗》.pdf

AGMA 10FTM13-2010 Gear Design for Wind Turbine Gearboxes to Avoid Tonal Noise According to ISO IEC 61400-11《依据ISO IEC 61400-11设计风力发电机组齿轮箱齿轮 以避免音调噪音》.pdf

AGMA 10FTM14-2010 Analysis and Testing of Gears with Asymmetric Involute Tooth Form and Optimized Fillet Form for Potential Application in Helicopter Main Drives《用非对称渐开线齿形结构和优化圆角结构.pdf

AGMA 10FTM15-2010 Drive Line Analysis for Tooth Contact Optimization of High Power Spiral Bevel Gears《驱动高功率螺旋锥齿轮齿接触的优化线性分析》.pdf