NEN 1324-1967 Turning and planing tools Nomenclature《车刀和刨刀 命名》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

DIN ISO 4226-2009 Air quality - General aspects - Units of measurement (ISO 4226 2007) English version of DIN ISO 4226 2009-02《空气质量 一般效应 测量装置》.pdf

DIN ISO 43-1981 Aerospace aircraft jacking pads《航空航天 飞机 千斤顶支板》.pdf

DIN ISO 4309-2013 Cranes - Wire ropes - Care and maintenance inspection and discard (ISO 4309 2010)《起重机 绳索 保养和维护、检修和报废(ISO 4309-2010)》.pdf

DIN ISO 4321-1982 Washing powders determination of active oxygen content titrimetric method《洗涤粉 活性氧含量的测定 滴定法》.pdf

DIN ISO 4324-1983 Surface active agents powders and granules measurement of the angle of repose《粉状和粒状表面活性剂 休止角的测定》.pdf

DIN ISO 4378-1-2013 Plain bearings - Terms definitions classification and symbols - Part 1 Design bearing materials and their properties (ISO 4378-1 2009)《滑动轴承 术语、定义、分类和符号 第1部分 设计、.pdf

DIN ISO 4378-2-2013 Plain bearings - Terms definitions classification and symbols - Part 2 Friction and wear (ISO 4378-2 2009)《滑动轴承 术语、定义、分类和符号 第2部分 摩擦和磨损(ISO 4378-2-2009)》.pdf

DIN ISO 4378-3-2013 Plain bearings - Terms definitions classification and symbols - Part 3 Lubrication (ISO 4378-3 2009)《滑动轴承 术语、定义、分类和符号 第3部分 润滑(ISO 4378-3-2009)》.pdf

DIN ISO 4378-4-2013 Plain bearings - Terms definitions classification and symbols - Part 4 Basic symbols (ISO 4378-4 2009)《滑动轴承 术语、定义、分类和符号 第4部分 基本符号(ISO 4378-4-2009)》.pdf