NEN 5482-1989 Quality requirements for timber Species iroko《木材的质量要求 伊罗科木》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSK-M3D154-A-2004 UNSATURATED POLYESTER (UP) INJECTION MOLDING COMPOUND 17% GLASS FIBER REINFORCED HIGH HEAT RESISTANT TO BE USED WITH FORD WSS-M99P1111-A 《17%玻璃纤维增强的耐高温不饱和聚.pdf

FORD WSK-M3D162-A-2004 PHENOLIC (PF) COMPRESSION MOLDING COMPOUND 50% MINERAL GLASS FIBER FILLED TO BE USED WITH FORD WSS-M99P1111-A 《50%矿物 玻璃纤维填充的酚醛树脂（PF）模压成型料 与标准FORD WSS-M99P.pdf

FORD WSK-M3D168-A1-2006 PHENOLIC (PF) 40% WOOD FLOUR FILLED INJECTION MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《40%木屑填充的酚醛树脂（PF）注塑成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD WSK-M3D168-A2-2004 PHENOLIC (PF) 40% WOOD FLOUR FILLED COMPRESSION MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《40%木屑填充的酚醛树脂（PF）模压成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD WSK-M3D175-A-1995 UNSATURATED POLYESTER (PU) 20% CONTINUOUS GLASS FIBER REINFORCED MOLDING COMPOUND《20%玻璃纤维增强的不饱和聚酯（PU）连续成型料》.pdf

FORD WSK-M3D176-A1-2005 PHENOLIC (PF) 35% GLASS FIBER REINFORCED COMPRESSION MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《35%玻璃纤维增强的酚醛树脂（PF）模压成型料 与标准FORD WSS-M99P1111-A.pdf

FORD WSK-M3D176-A2-2005 PHENOLIC (PF) 30% GLASS FIBER REINFORCED COMPRESSION MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《酚醛树脂（PF）30%玻璃纤维增强的模压成型料 与标准FORD WSS-M99P1111-A.pdf

FORD WSK-M3D176-A3-2005 PHENOLIC (PF) 30% GLASS FIBER REINFORCED PRE-PREG SHEET MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《酚醛树脂（PF）30%玻璃纤维增强的预浸处理片状成型料 与标准FORD WSS-M99.pdf

FORD WSK-M3G178-A-2013 TAPE DECORATIVE PRESSURE SENSITIVE EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf