NF C93-562 A2-1981 《NF C 93-562-1981的补充件2》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

BS 3409-1-1961 Specification for the tapping of holes to receive wire thread inserts (UNC and UNF threads) - Diameters 1 4 in and over《金属丝螺纹镶件承受孔攻螺纹(统一标准粗牙螺纹和统一标准细牙螺纹)规范 第1部分 孔径1 4.pdf

BS 3409-2-1966 Specification for the tapping of holes to receive wire thread inserts (UNC and UNF threads) - Diameters below 1 4 in《金属丝螺纹镶件承受孔攻螺纹(统一标准粗牙螺纹和统一标准细牙螺纹)规范 第2部分 孔径小于1 4英.pdf

BS 341-1-1991 Transportable gas container valves - Specification for industrial valves for working pressures up to and including 300 bar《可输气体容器阀门 第1部分 工作压力最大不超过300bar(包含300bar)用工业阀.pdf

BS 341-3-2002 Transportable gas container valves - Valve outlet connections《可运输气体容器的阀门 阀门出口接头》.pdf

BS 341-4-2004 Transportable gas container valves - Pressure relief devices《可运输气体容器的阀门 减压装置》.pdf

BS 3410-1961 Specification for metal washers for general engineering purposes《一般工程用金属垫圈规范》.pdf

BS 3412-1992 Methods of specifying general purpose polyethylene materials for moulding and extrusion《模塑和挤塑通用聚乙烯材料的规定方法》.pdf

BS 3416-1991 Specification for bitumen-based coatings for cold application suitable for use in contact with potable water《适用于与饮用水接触的冷涂沥青基覆层规范》.pdf

BS 3423-1986 Recommendations for design of glass vacuum vessels (including desiccators) for laboratory use《实验室用玻璃真空器(包括干燥器)的设计推荐规范》.pdf