NF T25-023-1996 Reinforcement materials Tubular braided sleeves Basis for a specification 《加固材料 管式编织管套 规范基础》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

EN ISO 17834-2003 en Thermal spraying Coatings for protection against corrosion and oxidation at elevated temperatures《热喷镀 防高温腐蚀和氧化的涂层 ISO 17834-2003》.pdf

EN ISO 17836-2004 en Thermal spraying - Determination of the deposition efficiency for thermal spraying《热喷涂 热喷涂沉积效率的测定 ISO 17836-2004》.pdf

EN ISO 17836-2017 en Thermal spraying - Determination of the deposition efficiency for thermal spraying.pdf

EN ISO 17852-2008 en Water quality - Determination of mercury - Method using atomic fluorescence spectrometry《水质 汞含量的测定 原子荧光分光光度测定法［代替 CEN EN 13506］》.pdf

EN ISO 17855-1-2014 en Plastics - Polyethylene (PE) moulding and extrusion materials - Part 1 Designation system and basis for specifications《塑料 聚乙烯(PE)模塑和挤塑材料 第1部分 规格的标志法和基础(ISO 1.pdf

EN ISO 17855-2-2016 en Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2 Preparation of test specimens and determination of properties《塑料聚乙烯(PE)模塑和挤出材料第2部分 试样的.pdf

EN ISO 17864-2008 en Corrosion of metals and alloys - Determination of the critical pitting temperature under potientiostatic control《金属和合金的腐蚀 静电位控制下临界点蚀温度的测定》.pdf

EN ISO 17871-2015 en Gas cylinders - Quick-release cylinder valves - Specification and type testing《气瓶 速动气缸阀门 规格和类型测试(ISO 17871 2015)》.pdf

EN ISO 17872-2007 en Paints and varnishes - Guidelines for the introduction of scribe marks through coatings on metallic panels for corrosion testing《涂料和清漆 腐蚀试验用金属板涂层画线器标记的入门指南》.pdf