1、NFPA 253 Standard Method of Test for Critical Radiant Flux of Floor Covering Systems Using a Radiant Heat Energy Source 2015 Edition NFPA , 1 Batterymarch Park, Quincy, MA 02169-7471, USA An International Codes and Standards Organization 1/14 ISBN: 978-145591045-8 (Print) ISBN: 978-145591091-5 (PDF)
2、 IMPORTANT NOTICES AND DISCLAIMERS CONCERNING NFPA STANDARDS NOTICE AND DISCLAIMER OF LIABILITY CONCERNING THE USE OF NFPA STANDARDS NFPA codes, standards, recommended practices, and guides (“NFPA Standards”), of which the document contained herein is one, are developed through a consensus standards
3、 development process approved by the American National Standards Institute. This process brings together volunteers representing varied viewpoints and interests to achieve consensus on fire and other safety issues. While the NFPA administers the process and establishes rules to promote fairness in t
4、he development of consensus, it does not independently test, evaluate, or verify the accuracy of any information or the soundness of any judgments contained in NFPA Standards. The NFPA disclaims liability for any personal injury, property or other damages of any nature whatsoever, whether special, i
5、ndirect, consequential or compensatory, directly or indirectly resulting from the publication, use of, or reliance on NFPA Standards. The NFPA also makes no guaranty or warranty as to the accuracy or completeness of any information published herein. In issuing and making NFPA Standards available, th
6、e NFPA is not undertaking to render professional or other services for or on behalf of any person or entity. Nor is the NFPA undertaking to perform any duty owed by any person or entity to someone else. Anyone using this document should rely on his or her own independent judgment or, as appropriate,
7、 seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. The NFPA has no power, nor does it undertake, to police or enforce compliance with the contents of NFPA Standards. Nor does the NFPA list, certify, test, or inspect products, desig
8、ns, or installations for compliance with this document. Any certification or other statement of compliance with the requirements of this document shall not be attributable to the NFPA and is solely the responsibility of the certifier or maker of the statement. REMINDER: UPDATING OF NFPA STANDARDS Us
9、ers of NFPA codes, standards, recommended practices, and guides (“NFPA Standards”) should be aware that NFPA Standards may be amended from time to time through the issuance of Tentative Interim Amendments or corrected by Errata. An official NFPA Standard at any point in time consists of the current
10、edition of the document together with any Tentative Interim Amendment and any Errata then in effect. In order to determine whether an NFPA Standard has been amended through the issuance of Tentative Interim Amendments or corrected by Errata, visit the Document Information Pages on NFPAs website. The
11、 Document Information Pages provide up-to-date, document specific information including any issued Tentative Interim Amendments and Errata. To access the Document Information Page for a specific NFPA Standard, go to http:/www.nfpa.org/docinfo to choose from the list of NFPA Standards or use the sear
12、ch feature on the right to select the NFPA Standard number (e.g., NFPA 101). In addition to posting all existing Tentative Interim Amendments and Errata, the Document Information Page also includes the option to sign-up for an “Alert” feature to receive an email notification when new updates and oth
13、er information are posted regarding the document.1/14 IMPORTANT NOTICES AND DISCLAIMERS CONCERNING NFPA STANDARDS ADDITIONAL NOTICES AND DISCLAIMERS Updating of NFPA Standards Users of NFPA codes, standards, recommended practices, and guides (“NFPA Standards”) should be aware that these documents ma
14、y be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of Tentative Interim Amendments or corrected by Errata. An official NFPA Standard at any point in time consists of the current edition of the document together with any Tentative Inte
15、rim Amendments and any Errata then in effect. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of Tentative Interim Amendments or corrected through the issuance of Errata, consult appropriate NFPA publications such as the Nati
16、onal Fire Codes Subscription Service, visit the NFPA website at www.nfpa.org, or contact the NFPA at the address listed below. Interpretations of NFPA Standards A statement, written or oral, that is not processed in accordance with Section 6 of the Regulations Governing the Development of NFPA Stand
17、ards shall not be considered the official position of NFPA or any of its Committees and shall not be considered to be, nor be relied upon as, a Formal Interpretation. Patents The NFPA does not take any position with respect to the validity of any patent rights referenced in, related to, or asserted
18、in connection with an NFPA Standard. The users of NFPA Standards bear the sole responsibility for determining the validity of any such patent rights, as well as the risk of infringement of such rights, and the NFPA disclaims liability for the infringement of any patent resulting from the use of or r
19、eliance on NFPA Standards. NFPA adheres to the policy of the American National Standards Institute (ANSI) regarding the inclusion of patents in American National Standards (“the ANSI Patent Policy”), and hereby gives the following notice pursuant to that policy: NOTICE: The users attention is called
20、 to the possibility that compliance with an NFPA Standard may require use of an invention covered by patent rights. NFPA takes no position as to the validity of any such patent rights or as to whether such patent rights constitute or include essential patent claims under the ANSI Patent Policy. If,
21、in connection with the ANSI Patent Policy, a patent holder has filed a statement of willingness to grant licenses under these rights on reasonable and nondiscriminatory terms and conditions to applicants desiring to obtain such a license, copies of such filed statements can be obtained, on request,
22、from NFPA. For further information, contact the NFPA at the address listed below. Law and Regulations Users of NFPA Standards should consult applicable federal, state, and local laws and regulations. NFPA does not, by the publication of its codes, standards, recommended practices, and guides, intend
23、 to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights NFPA Standards are copyrighted. They are made available for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations,
24、and use in private self-regulation, standardization, and the promotion of safe practices and methods. By making these documents available for use and adoption by public authorities and private users, the NFPA does not waive any rights in copyright to these documents. Use of NFPA Standards for regula
25、tory purposes should be accomplished through adoption by reference. The term “adoption by reference” means the citing of title, edition, and publishing information only. Any deletions, additions, and changes desired by the adopting authority should be noted separately in the adopting instrument. In
26、order to assist NFPA in following the uses made of its documents, adopting authorities are requested to notify the NFPA (Attention: Secretary, Standards Council) in writing of such use. For technical assistance and questions concerning adoption of NFPA Standards, contact NFPA at the address below. F
27、or Further Information All questions or other communications relating to NFPA Standards and all requests for information on NFPA procedures governing its codes and standards development process, including information on the procedures for requesting Formal Interpretations, for proposing Tentative In
28、terim Amendments, and for proposing revisions to NFPA standards during regular revision cycles, should be sent to NFPA headquarters, addressed to the attention of the Secretary, Standards Council, NFPA, 1 Batterymarch Park, P.O. Box 9101, Quincy, MA 02269-9101; email: stds_adminnfpa.org For more inf
29、ormation about NFPA, visit the NFPA website at www.nfpa.org. All NFPA codes and standards can be viewed at no cost at www.nfpa.org/freeaccess.Copyright 2014 National Fire Protection Association . All Rights Reserved. NFPA 253 StandardMethodof TestforCriticalRadiantFluxofFloorCoveringSystemsUsinga Ra
30、diantHeatEnergySource 2015Edition This edition of NFPA 253, Standard Method of Test for Critical Radiant Flux of Floor Covering Systems Using a Radiant Heat Energy Source, was prepared by the Technical Committee on Fire Tests. It was issued by the Standards Council on November 11, 2014, with an effe
31、ctive date of December 1, 2014, and supersedes all previous editions. This edition of NFPA 253 was approved as an American National Standard on Decem- ber 1, 2014. OriginandDevelopmentofNFPA253 Experience suggests that during the early stages of a fire, floor covering systems seldom act as a fire-sp
32、read medium. However, in a few fires involving multiple-occupancy buildings, the floor covering materials in corridors were primarily responsible for fire spread over a consid- erable distance. Those situations caused grave concern and pointed to the need for a realistic test to evaluate the flame s
33、pread of floor covering systems. The inception of the flooring radiant panel test was at the Armstrong Cork Company in 1966. In 1972, conceptualization of critical radiant flux (W/cm2 at extinguishment) as a measure of flame spread hazard was underway at the National Bureau of Standards (NBS). It wa
34、s determined in the course of NBS work on model corridor fire tests that the radiant energy levels incident on the floor covering had a considerable influence on whether or not flaming combustion would propagate. Accordingly, it was natural to apply the critical radiant flux concept, and, in 1973, t
35、he NBS prepared a draft of the flooring radiant panel test. In 1975, the Technical Committee on Fire Tests began its evaluation of the proposed test methods, which culminated in the adoption of the test as an official NFPA standard in May 1978. The standard was revised in 1984 and 1990. The 1995 edi
36、tion included significant improvements based on work conducted by the National Institute of Standards and Technology (NIST) and the carpet industry. Those findings improved the overall application of the standard and provided measured im- provement in test precision. Other changes included a new pil
37、ot burner and reduction of the variation in the airflow through the chamber, which reduced the variability of data. Revisions also were made to eliminate “permissive” language. The revisions created closer harmony with ASTM E648, Standard Test Method for Critical Radiant Flux of Floor-Covering Syste
38、ms Using a Radiant Heat Energy Source. The 2000 edition was a reconfirmation of the 1995 edition. The 2006 edition included a complete editorial rewrite for compliance with theManualof StyleforNFPATechnicalCommitteeDocuments. Further organizational and editorial changes were made to clarify the requ
39、irements of the test method. Provisions regarding safety precautions were moved to the annexes, and additional details were provided on simulating a concrete floor during the test. The 2011 edition was revised to create uniformity with other fire test standards. Provisions for laminate floor mountin
40、g were added to Chapter 5. The 2015 edition has been revised to provide clarity on airflow rates and provide updated examples of test apparatuses. 2531 NFPA and National Fire Protection Association are registered trademarks of the National Fire Protection Association, Quincy, Massachusetts 02169.Tec
41、hnicalCommitteeonFireTests BarryL.Badders,Jr., Chair Southwest Research Institute, TX RT ScottW.Adams, Park City Fire Service District, UT E Rep. International Fire Marshals Association FaridAlfawakhiri, American Iron and Steel Institute, IL M JesseJ.Beitel, Hughes Associates, Inc., MD SE JamesA.Bur
42、ns, New York State Department, NY E Rep. Firemens Association of the State of New York GordonH.Damant, Inter-City Testing & Consulting Corp. of California, CA SE ScottE.Dillon, Crane Engineering, IL SE WilliamE.Fitch, P, FL SE MarceloM.Hirschler, GBH International, CA SE PaulA.Hough, Armstrong World
43、 Industries, Inc., PA M MohammedM.Khan, FM Global, MA I WilliamE.Koffel, Koffel Associates, Inc., MD SE RichardT.Long,Jr., Exponent, Inc., MD M Rep. Upholstered Furniture Action Council MichaelE.Luna, Intertek Testing Services, TX RT AndreW.Marshall, University of Maryland, MD SE RodneyA.McPhee, Can
44、adian Wood Council, Canada M KathleenA.Newman, Firetect, CA M DavidT.Sheppard, U.S. Bureau of Alcohol, Tobacco, Firearms & Explosives, MD RT DwayneE.Sloan, UL LLC, NC RT KumaSumathipala, American Wood Council, DC M RobertA.Wessel, Gypsum Association, MD M Alternates ErikH.Anderson, Koffel Associates
45、, Inc., MD SE (Alt. to W. E. Koffel) RichardJ.Davis, FM Global, MA I (Alt. to M. M. Khan) TimothyEarl, GBH International, MI SE (Alt. to M. M. Hirschler) SamW.Francis, American Wood Council, PA M (Alt. to K. Sumathipala) StephenP.Fuss, U.S. Bureau of Alcohol, Tobacco, Firearms & Explosives, MD RT (A
46、lt. to D. T. Sheppard) MarcL.Janssens, Southwest Research Institute, TX RT (Alt. to B. L. Badders, Jr.) ArthurJ.Parker, Hughes Associates, Inc., MD SE (Alt. to J. J. Beitel) StanislavI.Stoliarov, University of Maryland, MD SE (Alt. to A. W. Marshall) InekeVanZeeland, Canadian Wood Council, Canada M
47、(Alt. to R. A. McPhee) RobertJ.Wills, American Iron and Steel Institute, AL M (Alt. to F. Alfawakhiri) JoeZiolkowski, American Furniture Manufacturers Association, NC M (Alt. to R. T. Long, Jr.) Nonvoting RobertH.Barker, American Fiber Manufacturers Association, VA M Rep. American Fiber Manufacturer
48、s Association RohitKhanna, U.S. Consumer Product Safety Commission, MD C TracyL.Vecchiarelli, NFPA Staff Liaison This list represents the membership at the time the Committee was balloted on the final text of this edition. Since that time, changes in the membership may have occurred.Akey to classifi
49、cations is found at the back of the document. NOTE: Membership on a committee shall not in and of itself constitute an endorsement of the Association or any document developed by the committee on which the member serves. Committee Scope: This Committee shall have primary responsibility for documents on fire testing proce- dures, for reviewing existing fire test standards and recommending appropriate action to NFPA, for recom- mending the application of and advising on the interpretation of accept
