1、 AEROSPACE STANDARD FITTING, LUBRICATION, HYDRAULIC, LEAKPROOF, 1/8 PIPE THREADS, STEEL, TYPE VI AS15006Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanica
2、l, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2001-05REAFFFIRMED
3、2014-11REVISED 2015-05THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.C FEDERAL SUPPLY CLASS 4730AS15006 SHEET 1 OF 3 REV. C PROCUREMENT SPECIFICATION: /5/ AS35411SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences.
4、Theuse ofthisreport is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized,
5、 orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS15006C RATIONALE REVISE AS15006 TO ADD PIPE THREAD NOTE /6/ FOR CLARITY, UPDATE TABLE 1 BY REMOVING THE WEIGHT OF STE
6、EL COLUMN AND CHANGING “B” DIMENSION, REMOVE THE DASH PRECEDING THE FINISH CODE FROM THE PART NUMBER, REMOVE INTERNATIONAL STANDARDIZATION AGREEMENT NOTE AND UPDATE INTERPRETATION SPECIFICATION. FIGURE 1 - FITTING, STRAIGHT FIGURE 2 - FITTING, ELBOW AEROSPACE STANDARD AS15006 SHEET 2 OF 3 REV. C FIT
7、TING, LUBRICATION, HYDRAULIC, LEAKPROOF, 1/8 PIPE THREADS, STEEL, TYPE VI FIGURE 3 - FITTING, ELBOW, 90 TABLE 1 - DIMENSIONS PART NUMBER /16/ FIG. THREAD T /6/ A .031 B /7/ C MAX. D MAX. E +.000 .003 F 5 AS15006-1 1 1/8-27 .375 .227 - .938 .438 - AS15006-2 2 1/8-27 .375 .264 .500 1.375 .438 30 AS150
8、06-3 2 1/8-27 .375 .264 .563 1.125 .438 65 AS15006-4 3 1/8-27 .375 .264 .625 1.000 .438 90 AS15006-5 3 1/8-27 .375 .264 .625 1.188 .438 105 NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS US
9、E. 1. MATERIAL: STEEL. SEE PROCUREMENT SPECIFICATION. 2. HEAT TREATMENT: NONE. /3/ FINISH: a. CODE LETTER C - CADMIUM PLATE, SEE PROCUREMENT SPECIFICATION. b. CODE LETTER P - ZINC PLATE, SEE PROCUREMENT SPECIFICATION. c. CODE LETTER U - ZINC NICKEL PLATE, SEE PROCUREMENT SPECIFICATION. 4. IDENTIFICA
10、TION: MARK PER AS478 METHOD 35D MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, AND PART NUMBER. AEROSPACE STANDARD AS15006 SHEET 3 OF 3 REV. C FITTING, LUBRICATION, HYDRAULIC, LEAKPROOF, 1/8 PIPE THREADS, STEEL, TYPE VI /5/ PROCUREMENT SPECIFICATION: AS35411 EXCEPT AS SPECIFIED ON THIS STANDARD. THE DR
11、AWING AND ALL THE SPECIFIED DOCUMENTS DEFINE THE REQUIREMENTS FOR THE END PRODUCT. ALL THE REQUIREMENTS MUST BE MET IN ORDER TO IDENTIFY THE ITEM WITH THAT PART NUMBER. USERS OF THIS STANDARD ARE ADVISED TO CONTROL SOURCE APPROVAL BY STANDARD PAGE SUPPLEMENT OR SIMILAR MEANS. /6/ PIPE THREADS SHALL
12、BE NPTF (DRY SEAL) IN ACCORDANCE WITH FED-STD-H28/8, SCREW THREAD STANDARDS FOR FEDERAL SERVICES; EXCEPT FOR -1 WHICH SHALL BE PTF-SHORT (DRY SEAL) IN ACCORDANCE WITH SAE J476. WIDTH OF FLAT ON THREAD CREST MAY BE .007 MAXIMUM. /7/ MINIMUM EFFECTIVE THREAD LENGTH. /8/ FITTING END IN ACCORDANCE WITH
13、AS15000, STYLE OPTIONAL. 9. INTENDED USE: THIS PART IS INTENDED FOR USE IN LUBRICATING CONNECTIONS. 10. THIS STANDARD IS A CONVERSION OF MILITARY STANDARD MS15006, FITTINGS, LUBRICATION (HYDRAULIC) LEAKPROOF, 1/8 PIPE THREADS, STEEL, TYPE VI, AND IS NOT A WORD-FOR-WORD CONVERSION. 11. INTERPRETATION
14、 OF DRAWING PER AS4296. 12. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra. SURFACES OF HEX FLATS MAY BE 250 MICROINCHES Ra. 13. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 14. DIMENSIONS ARE IN INCHE
15、S. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 030. 15. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. /16/ EXAMPLE OF PART NUMBER: AS15006-1 PBASIC PART NUMBER FITTING CONFIGURATION FINISH /3/17. INVENTORIED PARTS CONFORMING TO THE PREVIOUS LETTER CHANGE
16、 MAY BE USED TO DEPLETION. 18. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
