1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref
2、rom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2016 SAE InternationalAll rights reserved. No part of this publi
3、cation may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (out
4、side USA)Fax: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on thisTechnical Report, please visithttp:/standards.sae.org/AS23053AEROSPACESTANDARDAS23053Issued 2016-10Superseding AMS-DTL-23053Insulation Sleeving, Electrical, Heat
5、 Shrinkable,General Specification For(Federal Supply Class 5970)RATIONALEThis is a conversion of AMS-DTL-23053 into an AS document which includes Qualification. This also includes revisions due to comments received by the government and industry, updated references, alignment of the specification wi
6、th SAE guidelines and review of the specification for known technical problems. 1. SCOPE1.1 FormThis specification establishes the requirements for various types and colors of electrical insulating sleeving that will shrink to a predetermined size upon the application of heat. This specification inc
7、ludes provisions for demonstrating compliance with qualification requirements (see Section 4 and 7.3), in process inspection, and statistical process control inspections (see 4.4). The continuous operating temperature ranges for the sleeving classes covered by this specification are from -112to +482
8、 F (-80 to +250 C). The continuous operating temperature range for each sleeving class is given in the applicable detail specification.1.2 ClassificationThe heat shrinkable sleeving class shall be defined and specified in the applicable detail specification.1.3 ColorThe color shall be identified in
9、accordance with the following:Table 1Designator Color Designator Color0 Black 7 Violet (Purple)1 Brown 8 Gray (Slate)2 Red 9 White3 Orange C Clear4 Yellow P Pink5 Green T Tan6 BlueSAE INTERNATIONAL AS23053 Page 2 of 232. REFERENCES2.1 Applicable DocumentsThe following publications form a part of thi
10、s document to the extent specified herein. The latest issue of SAE publications shall apply. The applicable issue of other publications shall be the issue in effect on the date of the purchase order. In theevent of conflict between the text of this document and references cited herein, the text of t
11、his document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.2.1.1 SAE PublicationsAvailable from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Cana
12、da) or +1 724-776-4970 (outside USA), www.sae.org.AMS1424 Deicing/Anti-Icing Fluid, Aircraft, SAE Type IAMS-I-23053/2 Insulation Sleeving, Electrical, Heat Shrinkable, Polyvinyl Chloride, Flexible, Crosslinked and Non-CrosslinkedAMS-I-23053/3 Insulation Sleeving, Electrical, Heat Shrinkable, Polyvin
13、yl Chloride, Semi Rigid, Crosslinked and Non-CrosslinkedAS23053/1* Insulation Sleeving, Electrical, Heat Shrinkable, Crosslinked Chlorinated Polyolefin, FlexibleAS23053/2* Insulation Sleeving, Electrical, Heat Shrinkable, Polyvinyl Chloride, Flexible, Crosslinked and Non-Crosslinked (Stabilized)AS23
14、053/3* Insulation Sleeving, Electrical, Heat Shrinkable, Polyvinyl Chloride, Semi Rigid, Crosslinked and Non-Crosslinked (Stabilized)AS23053/4* Insulation Sleeving, Electrical, Heat Shrinkable, Polyolefin, Dual-Wall, Outer Wall CrosslinkedAS23053/5* Insulation Sleeving, Electrical, Heat Shrinkable,
15、Polyolefin, Flexible, CrosslinkedAS23053/6* Insulation Sleeving, Electrical, Heat Shrinkable, Polyolefin, Semi-Rigid, CrosslinkedAS23053/7* Insulation Sleeving, Electrical, Heat Shrinkable, Polyethylene Terephthalate, Non-CrosslinkedAS23053/8* Insulation Sleeving, Electrical, Heat Shrinkable, Polyvi
16、nylidene Fluoride, Semi-Rigid, CrosslinkedAS23053/10* Insulation Sleeving, Electrical, Heat Shrinkable, Silicone Rubber, FlexibleAS23053/11* Insulation Sleeving, Electrical, Heat Shrinkable, Fluorinated Ethylene Propylene, Non-CrosslinkedAS23053/12* Insulation Sleeving, Electrical, Heat Shrinkable,
17、PolytetrafluoroethyleneAS23053/13* Insulation Sleeving, Electrical, Heat Shrinkable, Fluoroelastomer, FlexibleAS23053/14* Insulation Sleeving, Electrical, Heat Shrinkable, Ethylene-Tetrafluoroethylene Fluoropolymer, Semi-RigidAS23053/15* Insulation Sleeving, Electrical, Heat Shrinkable, Polyolefin,
18、Heavy-Wall, Coated, Flexible, Outer Wall CrosslinkedAS23053/16* Insulation Sleeving, Electrical, Heat Shrinkable, Crosslinked, Elastomeric Polyolefin, FlexibleAS23053/17* Insulation Sleeving, Electrical, Heat Shrinkable, Flame Retarded, Modified Polyolefin, Flexible, Crosslinked (Stabilized)SAE INTE
19、RNATIONAL AS23053 Page 3 of 23AS23053/18* Insulation Sleeving, Electrical, Heat Shrinkable, Modified Fluoropolymer, Crosslinked*AS23053 detail specifications. Detail specification document numbers assigned to follow the numbers of previous specifications AMS-DTL-23053, MIL-I-23053, MIL-DTL-23053, an
20、d AMS-I-23053 (see 7.2 and 7.6).2.1.2 ASTM PublicationsAvailable from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org.ASTM D149 Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrica
21、l Insulating Materials at Commercial Power FrequenciesASTM D150 Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical InsulationASTM D374M Standard Test Methods for Thickness of Solid Electrical Insulation (Metric)ASTM D412 Standard Test Methods
22、 for Vulcanized Rubber and Thermoplastic Elastomers - TensionASTM D570 Standard Test Method for Water Absorption of PlasticsASTM D638 Standard Test Method for Tensile Properties of PlasticsASTM D746 Standard Test Method for Brittleness Temperature of Plastics and Elastomers by ImpactASTM D792 Standa
23、rd Test Methods for Density and Specific Gravity (Relative Density) of Plastics by DisplacementASTM D876 Standard Test Methods for Non-rigid Vinyl Chloride Polymer Tubing used for Electrical InsulationASTM D882 Standard Test Method for Tensile Properties of Thin Plastic SheetingASTM D2671 Standard T
24、est Methods for Heat-Shrinkable Tubing for Electrical UseASTM G21 Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi2.1.3 ISO PublicationsCopies of these documents are available online at http:/webstore.ansi.org/.ISO 846 Plastics - Evaluation of the action of micr
25、oorganismsISO 9001 Quality management systems RequirementsISO 10012 Measurement management systems - Requirements for measurement processes and measuring equipment2.1.4 National Conference of Standards Laboratories (NCSL) PublicationsAvailable from NCSL International, 2995 Wilderness Place, Suite 10
26、7, Boulder, CO 80301, Tel: 303-440-3339, www.ncsli.org.NCSL Z540.3 Requirements for the Calibration of Measuring and Test EquipmentSAE INTERNATIONAL AS23053 Page 4 of 232.1.5 U.S. Government PublicationsCopies of these documents are available online at http:/quicksearch.dla.mil.SD-6 Provisions Gover
27、ning QualificationA-A-694 Sodium Chloride, TechnicalFED-STD-228 Cable and Wire, Insulated; Methods of TestingMIL-DTL-23053 Insulation Sleeving, Electrical, Heat Shrinkable, General Specification forMIL-DTL-23053/1 Insulation Sleeving, Electrical, Heat Shrinkable, Crosslinked Chlorinated Polyolefin,
28、FlexibleMIL-DTL-23053/4 Insulation Sleeving, Electrical, Heat Shrinkable, Polyolefin, Dual-Wall, Outer Wall CrosslinkedMIL-DTL-23053/5 Insulation Sleeving, Electrical, Heat Shrinkable, Polyolefin, Flexible, CrosslinkedMIL-DTL-23053/6 Insulation Sleeving, Electrical, Heat Shrinkable, Polyolefin, Semi
29、-Rigid, CrosslinkedMIL-DTL-23053/7 Insulation Sleeving, Electrical, Heat Shrinkable, Polyethylene Terephthalate, Non-CrosslinkedMIL-DTL-23053/8 Insulation Sleeving, Electrical, Heat Shrinkable, Polyvinylidene Fluoride, Semi-Rigid, CrosslinkedMIL-DTL-23053/10 Insulation Sleeving, Electrical, Heat Shr
30、inkable, Silicone Rubber, FlexibleMIL-DTL-23053/11 Insulation Sleeving, Electrical, Heat Shrinkable, Fluorinated Ethylene Propylene, Non-CrosslinkedMIL-DTL-23053/12 Insulation Sleeving, Electrical, Heat Shrinkable, PolytetrafluoroethyleneMIL-DTL-23053/13 Insulation Sleeving, Electrical, Heat Shrinka
31、ble, Fluoroelastomer, FlexibleMIL-DTL-23053/14 Insulation Sleeving, Electrical, Heat Shrinkable, Ethylene-Tetrafluoroethylene Fluoropolymer, Semi-RigidMIL-DTL-23053/15 Insulation Sleeving, Electrical, Heat Shrinkable, Polyolefin, Heavy-Wall, Coated, Flexible, Outer Wall CrosslinkedMIL-DTL-23053/16 I
32、nsulation Sleeving, Electrical, Heat Shrinkable, Crosslinked, Elastomeric Polyolefin, FlexibleMIL-DTL-23053/17 Insulation Sleeving, Electrical, Heat Shrinkable, Flame Retarded, Modified Polyolefin, Flexible, CrosslinkedMIL-DTL-23053/18 Insulation Sleeving, Electrical, Heat Shrinkable, Modified Fluor
33、opolymer, CrosslinkedMIL-DTL-83133 Turbine Fuels, Aviation, Kerosene Types, NATO F-34 (JP-8), NATO F-35, and JP-8+100MIL-I-23053 Insulation Sleeving, Electrical, Heat Shrinkable, General Specification forMIL-I-23053/2 Insulation Sleeving, Electrical, Heat Shrinkable, Polyvinyl Chloride, Flexible, Cr
34、osslinked and Non-CrosslinkedMIL-I-23053/3 Insulation Sleeving, Electrical, Heat Shrinkable, Polyvinyl Chloride, Semi Rigid, Crosslinked and Non-CrosslinkedMIL-I-23053/9 Insulation, Sleeving, Electrical, Heat Shrinkable, Fluorosilicone Rubber, FlexibleSAE INTERNATIONAL AS23053 Page 5 of 23MIL-PRF-56
35、06 Hydraulic Fluid, Petroleum Base; Aircraft, Missile, and OrdnanceMIL-PRF-7808 Lubricating Oil, Aircraft Turbine Engine, Synthetic BaseMIL-PRF-23699 Lubricating Oil, Aircraft Turbine Engine, Synthetic Base, NATO code Number O-156MIL-STD-104 Limit for Electrical Insulation Color2.2 Definitions2.2.1
36、QUALIFICATION INSPECTION: Qualification Inspection is a process that demonstrates that a component is capable of fully conforming to all the requirements defined in a standard. Qualification Inspection includes definition of the measurements, tests, analysis, and associated data which provides consi
37、stent rationale for acceptance of a particular suppliers design as meeting the standard requirements typically prior to acquisition by the Purchaser.2.2.2 QUALIFIED PRODUCTS LIST: A Qualified Products List is a list of suppliers whose products have been evaluated to a defined process and who are aut
38、horized to provide those products to a purchaser upon request. When a Qualified Products List is specified, only approved suppliers are authorized to provide products under the part number defined in the component standard. A Qualified Products List is established by a Qualifying Activity.2.2.3 QUAL
39、IFYING ACTIVITY: The Qualifying Activity for U.S. Department of Defense procurement purposes, is the Naval Air Systems Command (Code 4.4.5.3), 48298 Shaw road, Bldg. 1461, Patuxent River, MD 20670. Application for qualification tests shall be made in accordance with provisions governing qualificatio
40、n in SD-6 (see 2.1.5).2.2.4 QUALITY CONFORMANCE INSPECTION: Quality Conformance Inspection is a process which includes measurements, non-destructive tests, analysis and associated data that will provide verification that a particular individual component continually conforms to the requirements defi
41、ned in the standard.2.2.5 PURCHASER: A Purchaser is an individual or group of individuals that can issue a purchase order.2.2.6 SUPPLIER: A Supplier is a manufacturer which has design and production control of the processes used to produce a component.2.2.7 REBRAND SUPPLIER: A Rebrand Supplier is a
42、manufacturer or distributor approved by the qualified supplier and the qualifying activity to sell the original suppliers product as the rebrand suppliers own product defined by the rebrand supplier part number. A Rebrand Supplier is also known as a private labeler.2.2.8 DATE OF MANUFACTURE: The dat
43、e at which the sleeving is expanded to its final “as supplied” ID. 3. REQUIREMENTS3.1 Detail SpecificationsIn the event of a conflict between the text of this document and the references cited herein (except for related associated specifications or detail specifications), the text of this document t
44、akes precedence. Nothing in the document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.3.2 Dimensions and TolerancesDimensions and properties in inch/pound units and the Fahrenheit temperatures are primary. Dimensions and properties in SI units an
45、d the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information.3.2.1 Inside Diameter (ID)3.2.1.1 As SuppliedWhen determined in accordance with 5.3.1, the “as supplied” ID shall conform to the requirements of the applicable detail speci
46、fication.SAE INTERNATIONAL AS23053 Page 6 of 233.2.1.2 After Unrestricted ShrinkageWhen determined in accordance with 5.3.2, the sleeving ID after unrestricted shrinkage shall conform to the requirements of the applicable detail specification.3.2.2 Wall ThicknessThe wall thickness after unrestricted
47、 shrinkage shall be determined in accordance with 5.3.3 and shall conform to the requirement in the detail specification.3.2.3 Longitudinal ChangeWhen tested as specified in 5.4, the longitudinal change shall not exceed the value specified in the detail specification.3.2.4 ConcentricityWhen tested a
48、s specified in 5.3.4 the “as supplied” concentricity shall not be less than that specified in the detail specification.3.2.5 Unit of IssueUnit of issue for all sleeving shall be feet (meters). The sleeving shall be supplied as a straight piece, coiled, on reels or spools.3.2.5.1 Straight PiecesUnles
49、s otherwise specified in the applicable detail specification, the standard straight piece unit of issue shall be 4 feet plus 2/minus 0 inches (121.9 cm plus 5/minus 0 cm).3.2.5.2 Reels, Spools, and CoilsUnless otherwise specified in the purchasers contract or order (see 7.3 d), sleeving length on reels shall be as specified inTable 2.Table 2 - Reel lengths 1/ID, As Suppliedinch (mm)Minimum Length feet (m)Number of Lengths maxim
