1、 AEROSPACE STANDARD CONNECTOR, RECEPTACLE, ELECTRIC, BOX MOUNTING, REAR RELEASE, CRIMP CONTACT, AN TYPE ASCopyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechani
2、cal, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2004-06REVISED2017
3、-02THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.C FEDERAL SUPPLY CLASS 5935 AS SHEET 1 OF 3 REV. C PROCUREMENT SPECIFICATION: AS50151 6$(7HFKQLFDO6WDQGDUGV%RDUG5XOHVSURYLGHWKDW7KLVUHSRUWLVSXEOLVKHGE6$(WRDGYDQFHWKHVWDWHRIWHFKQLFDODQGHQJLneering sciences. The useof this report is entirely volunta
4、ry, and its applicability andsuitability for any particularusHLQFOXGLQJDQSDWHQWLQIULQJHPHQWDULVLQJWKHUHIURPLVWKHVROHUHVSRQVLELOLWRIWKHXVHUSAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments an
5、d suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS34521C RATIONALE REVISION IS REQUIRED TO ADD AN APPLICATION NOTE TO CLARIFY THE ENVIRONMENTAL SEALING PROPERTIES OF THIS CONNECTOR. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING
6、 THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS50151. FIGURE 1 - CONNECTOR CONFIGURATION (CLASSES L, U, AND W ENVIRONMENT RESISTANT INTERFACE ONLY) AEROSPACE STANDARD AS SHEET 2 OF 3 REV. C CONNECTOR, RECEPTACLE, ELECTRIC, BOX MOUNTING, REAR RELEASE, CRIMP CON
7、TACT, AN TYPE TABLE 1 - DIMENSIONS REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS50151. 1. DESIGN: CONNECTORS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 1. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: DECIMALS .016. DIMENSIO
8、NS AND TOLERANCING SHALL BE IN ACCORDANCE WITH ANSI/ASME Y14.5M-1994. AS50151 CRIMP CONTACT, FRONT AND REAR RELEASE CONNECTORS AND SOLDER CONTACT CONNECTORS ARE INTERMATEABLE. UNLESS OTHERWISE SHOWN, CORRESPONDING FEATURES OF PIN AND SOCKET CONTACT CONNECTORS ARE IDENTICAL. THE INSULATION MATERIAL S
9、HALL BE ABOVE, FLUSH WITH, OR NO MORE THAN .015 INCH BELOW THE METAL SHELL AND ALL CONTACTS SHALL BE RECESSED BELOW THE INSULATION MATERIAL. TOOLS USED FOR INSERTING AND REMOVAL OF CONTACTS SHALL BE AS SPECIFIED IN AS50151. 2. FOR INSERT ARRANGEMENTS SEE MIL-STD-1651. SIZE GG .016 K .015 L MAX M +.0
10、31 .000 N +.000 .062 O (REF) MTG HOLES R C1.C1 S .031 T +.010 .005 SIZE 16 & 12 CONTACTS SIZE 8, 4 & 0 CONTACTS 8S .500 .083 1.662 N/A .562 .532 .562 .594 .875 .120 10S .625 .656 .688 .719 1.000 10SL 12S .750 .782 .812 .812 1.094 12 .750 14S .875 .562 .906 .938 .906 1.188 14 .750 16S 1.000 .562 1.03
11、2 1.062 .969 1.281 16 1.937 .750 18 1.052 .125 1.156 1.188 1.062 1.375 20 1.187 1.282 1.312 1.156 1.500 22 1.312 1.406 1.438 1.250 1.625 24 1.437 .812 1.532 1.562 1.375 1.750 .147 28 1.750 1.782 1.812 1.562 2.000 32 2.000 .875 2.032 2.062 1.750 2.250 .173 36 2.250 2.282 2.312 1.938 2.500 40 2.500 2.
12、532 2.562 2.188 2.750 44 2.750 2.782 2.812 2.375 3.000 48 3.000 3.032 3.062 2.625 3.250 AEROSPACE STANDARD AS SHEET 3 OF 3 REV. C CONNECTOR, RECEPTACLE, ELECTRIC, BOX MOUNTING, REAR RELEASE, CRIMP CONTACT, AN TYPE 3. THE PART NUMBERS SHALL BE AS SHOWN IN THE EXAMPLE BELOW: SPECIFICATION NOTES NOTICE
13、 THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCE51,1*&$0,80686( 1. REVISION INDICATOR: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDI
14、TORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHAN
15、GES ONLY. APPLICATION NOTES 1. THE FRONT FACE OF THIS CONNECTOR PROVIDES ENVIRONMENTAL SEALING WHEN COUPLED TO ITS CORRESPONDING PLUG CONNECTOR AND FULLY LOADED WITH THE APPLICABLE CONTACTS. THE REAR OF THIS CONNECTOR IS NON-ENVIRONMENTAL AND THE CONNECTOR IS INTENDED FOR USE ON BOXES WHERE THE REAR
16、 ENVIRONMENTAL SEAL IS ACHIEVED BY SOME OTHER MEANS. 2. AS34521 SUPERSEDES MS3452. BASIC PART NO. CLASS L, U OR W MATERIAL DESIGNATOR S-STAINLESS STEEL, LEAVE BLANK FOR ALUMINUM ALLOY SHELL SIZE INSERT ARRANGEMENT CONTACT DESIGNATOR ALTERNATE INSERT POSITION W, X, Y, OR Z. LEAVE BLANK FOR NORMAL POSITION MS3452 W 22 3 S Y
