1、 AEROSPACE STANDARD FITTING ASSEMBLY, TEE, FLARELESS AND SHORT FLARELESS, REDUCER, RETAINED NUT ON SIDE AS4692Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mec
2、hanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED1992-07 REAFFI
3、RMED2007-11 REVISED2017-10THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.FFEDERAL SUPPLY CLASS 4730 AS4692 SHEET 1 OF 6 REV. F PROCUREMENT SPECIFICATION: AS18280 /4/ SAETechnicalStandardsBoard Rulesprovidethat:“Thisreportispublished bySAEto advance the state oftechnicaland engineering sciences.The u
4、se ofthisreportisentirelyvoluntary,anditsapplicabilityandsuitabilityforanyparticularuse,includinganypatentinfringementarising therefrom,isthe sole responsibilityoftheuser.”SAEreviewseachtechnicalreportatleasteveryfiveyearsatwhich time itmaybe revised,reaffirmed,stabilized,orcancelled.SAEinvitesyourw
5、ritten commentsandsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS4692F RATIONALE ADDED CONDUCTIVE HIGH PURITY ALUMINUM COATING FOR ALUMINUM ALLOY FITTINGS. FIGURE 1 - TEE ASSEMBLY FIGURE 2 - INSTALLATION, RETAINED NUT AND RETAI
6、NING WIRE AEROSPACE STANDARD AS4692 SHEET 2 OF 6 REV. F FITTING ASSEMBLY, TEE, FLARELESS AND SHORT FLARELESS, REDUCER, RETAINED NUT ON SIDE TABLE 1 - DIMENSIONS AND WEIGHTS BASIC NO. AS4692 /10/ /20/ SIZE CODE D H J +.005/-.020 LB/EA APPROX REF ALUM LB/EA APPROX REF CRES LB/EA APPROX REF TI 20 .517
7、124 1.375 .395 1.146 .666 24 .614 .156 1.688 .570 1.651 .954 TABLE 2 - WIRE INSERTION DEPTH PORT SIZE (NOMINAL TUBE SIZE) C 04 .250 .076 05 .312 .076 06 .375 .084 08 .500 .095 10 .625 .114 12 .750 .150 16 1.000 .176 20 1.250 .247 24 1.500 .287 TABLE 3 - LEG LENGTH A SIZE OF PORT #1 FOR ALL PORTS TH
8、E SAME SIZE USE AS4674. /11/ PORT #1 IS LARGER OR EQUAL TO PORT #2. /12/ FINISH CODE LETTER “P” SHALL BE PLACED AFTER SIZE CODES ONLY FOR MATERIAL CODE “V” PARTS THAT ARE TO BE CADMIUM PLATED. FINISH CODE LETTER “V” SHALL BE PLACED AFTER SIZE CODES ONLY FOR MATERIAL CODE “W” PARTS THAT ARE TO BE COA
9、TED WITH HIGH PURITY ALUMINUM TO PROVIDE LOW ELECTRICAL CONTACT RESISTANCE. NO OTHER LETTERS ARE TO FOLLOW THE SIZE CODES. 13. REVISION INDICATOR: A CHANGE BAR (L) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE B
10、EEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 14. INVENTOR
11、IED PARTS CONFORMING TO THE PREVIOUS “LETTER CHANGE” MAY BE USED TO DEPLETION /4/. 15. INTERPRETATION OF DRAWING PER AS4296. 16. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36 M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES RA. FORGE SURFACES MAY BE 250
12、RA. AEROSPACE STANDARD AS4692 SHEET 6 OF 6 REV. F FITTING ASSEMBLY, TEE, FLARELESS AND SHORT FLARELESS, REDUCER, RETAINED NUT ON SIDE 17. BREAK EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 18. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994 19. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOL
13、ERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 5 DEGREES. /20/ EXAMPLE OF PART NUMBER: AS4692 V 20 16 20 PBA SIC PA RT NUMBER FINISH CODE LETTER /3/ /12/MA TERIA L CODE LETTER /1/ SIZ E CODE, TUBE SIZ E OFPORT #3 IN .062 INCREMENTSSIZ E CODE, TUBE SIZ E OF /10/PORT #1 IN .062 INCREMENTS/10/11/SIZ E CODE, TUBE SIZ E OFPORT #2 IN .062 INCREMENTS/10/11/
