1、 AEROSPACE STANDARD FITTING, SLEEVE, STRAIGHT, FLARED, EXTERNAL SWAGE, HYDRAULIC AS5012Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying,
2、recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1997-11REAFFIRMED2015-04THIRD ANGLE
3、PROJECTION CUSTODIAN: G-3/G-3B FEDERAL SUPPLY CLASS 4730AS5012 SHEET 1 OF 3 PROCUREMENT SPECIFICATION: /4/ AS4459SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is entirelyvoluntary, andits
4、applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments and
5、suggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS5012 RATIONALE AS5012 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. FIGURE 1 - CONFIGURATION FOR SIZE 04 THRU 12 ONLYFIGURE 2 - CONFIGURATION FO
6、R SIZE 03 ONLYAEROSPACE STANDARD AS5012 SHEET 2 OF 3 FITTING, SLEEVE, STRAIGHT, FLARED, EXTERNAL SWAGE, HYDRAULIC NOTES:/1/ MATERIAL:a. CODE LETTER “”: 21-6-9 CRES BAR PER AMS 5656b. CODE LETTER “E”: COMMERCIALLY PURE TITANIUM BAR PER AMS 4921c. CODE LETTER “D”: 6061T6 ALUMINUM ALLOY PER AMS 4150/2/
7、 FINISH:a. MATERIAL CODE “”: PASSIVATE PER QQ-P-35 TYPE VII, PTFE COAT (GREEN) BORE DIAMETER TO “V” DEPTH, OVERSPRAY ON “Y” PERMISSIBLE.b. MATERIAL CODE “E”: PTFE COAT (COLOR BLACK) EXTERIOR SURFACES AND BORE DIAMETER TO “V” DEPTH UNLESS OTHERWISE SPECIFIED /9/ /16/. AA TO BE FREE OF PTFE COATING.c.
8、 MATERIAL CODE “D”: CHEMICAL FILM FINISH ENTIRE PART (INCLUDING INTERNAL DIAS) PER MIL-C-5541, CLASS 1A, PTFE COAT (GREEN) EXTERNAL SURFACE EXCEPT AS NOTED AND BORE DIAMETER TO “V” DEPTH./3/ FILL OUTER GROOVES FOR CRES AND TITANIUM WITH SILICONE. FILL ALL GROOVES FOR ALUMINUM WITH SILICONE ELASTOMER
9、/4/ THIS PART SHALL BE QUALIFIED TO THE PROCUREMENT SPECIFICATION IN A COMPLETE ASSEMBLY. USERS OF THIS STANDARD ARE ADVISED TO CONTROL SOURCE APPROVAL(S) BY STANDARD PAGE SUPPLEMENT SHEET OR SIMILAR MEANS.TABLE 1 - DIMENSIONSBASIC NO.AS5012/16/SIZE CODENOMINALTUBESIZEA.015 B CTOLFORCD E FG+.000.01
10、5H+.000.003V/2/ AA03 .188 .900 .139 .136 +.005.001- .195/ .198 .326 .750 .275 .170/.220 .1304 .250 1.035 .157 .175 +.000.015.309/.312 .257/ .260 .379 .765 .338 .190/.240 .2205 .312 1.075 .222 .237 +.000.015.376/.379 .319/ .322 .442 .805 .413 .200/.250 .2206 .375 1.061 .235 .301 +.000.015.442/.445 .3
11、82/ .385 .504 .840 .480 .220/.270 .2208 .500 1.581 .237 .395 +.000.015.592/.595 .508/ .511 .684 1.343 .655 .410/.435 .5010 .625 1.582 .250 .531 +.008.001.712/.715 .633/ .636 .800 1.383 .787 .410/.435 .5012 .750 1.682 .319 .656 +.008.001.858/.861 .758/ .761 .975 1.453 .929 .365/.390 .50TABLE 2 - WEIG
12、HTSSIZE CODENOMINAL TUBE SIZE03.18804.25005.31206.37508.50010.62512.750LB/EA MAX CRES .00570 .0110 .0150 .0180 .0450 .0580 .0820LB/EA MAX TITANIUM .00330 .00660 .00900 .0100 .0260 .0330 .0470LB/EA MAX ALUMINUM .00200 .00400 .00500 .00600 .0150 .0200 .0280AEROSPACE STANDARD AS5012 SHEET 3 OF 3 FITTIN
13、G, SLEEVE, STRAIGHT, FLARED, EXTERNAL SWAGE, HYDRAULIC NOTES (CONTINUED):5. SPECIFIC DIMENSIONS AND TOLERANCES NOT DEFINED ON THIS STANDARD SHALL BE SPECIFIED AND CONTROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO ENSURE COMPATIBILITY WITH THE ASSEMBLY AND COMPLIANCE WITH THE PROCURE
14、MENT SPECIFICATION./6/ IDENTIFICATION: PARTS SHALL BE IDENTIFIED IN THE AREA SHOWN PER AS4459.7. INTENDED USE: PER AS4459./8/ THE AS5023 COUPLING NUT OF LIKE MATERIAL TO THE FITTING MUST BE PLACED ON THE TUBE PRIOR TO SWAGING AND THEN, AFTER SWAGING, SLIPPED OVER SWAGED END AGAINST THE SHOULDER OF T
15、HE FITTING./9/ FOR TITANIUM AND ALUMINUM FITTINGS, THIS EXTERNAL AREA SHALL BE FREE OF PTFE.10. LIQUID PENETRANT INSPECT PER ASTM E 1417 TYPE 1 SENSITIVITY 2. LINEAR INDICATIONS PROHIBITED, ROUNDED INDICATIONS ACCEPTABLE.11. INTERPRETATION OF DRAWING PER ARP4296.12. SURFACE TEXTURE: SYMBOLS PER ANSI
16、 Y14.36; REQUIREMENTS PER ANSI/ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra.13. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED.14. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994.15. DIMENSIONS IN INCHES; UNLESS OTHERWISE SPECIFIED, TOLERANCES: DIMENSIONS LINEAR .010,ANGULAR 2./16/
