1、 AEROSPACE STANDARD FITTING, CONNECTOR, MULTIPLE FLUID PRESSURE LINE, 45 AS5164Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recordin
2、g, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2000-07REVISED 2003-08 REAFFIRMED 2015-04THI
3、RD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.A FEDERAL SUPPLY CLASS 4730AS5164 SHEET 1 OF 3 REV. A PROCUREMENT SPECIFICATION: /4/ AS4875/1SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreportis enti
4、relyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites
5、yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS5164A RATIONALE AS5164A HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. FIGURE 1 - FITTING, CONNECTOR, 45AEROSPACE STANDARD
6、 AS5164 SHEET 2 OF 3 REV. A FITTING, CONNECTOR, MULTIPLE FLUID PRESSURE LINE, 45 NOTES:/1/ MATERIAL:a. DASH AS CODE LETTER - TYPE 4130 CARBON STEEL FORGING OR BAR PER AMS-S-6758 OR AMS 6370; OR TYPE 4140 PER AMS 6382. /2/b. CODE LETTER D - TYPE 2014-T6 ALUMINUM ALLOY FORGING PER AMS 4133; OR TYPE 20
7、24-T6 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6 OR TYPE 2024-T851 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6 OR AMS 4339. /2/c. CODE LETTER J - TYPE 304 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS 5639.d. CODE LETTER K - TYPE 316 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763
8、OR AMS 5648.e. CODE LETTER R - TYPE 321 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS 5645.f. CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY FORGING OR BAR PER AMS 4928.g. CODE LETTER W - TYPE 7075-T73 ALUMINUM ALLOY FORGING PER AMS 4141; OR TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ
9、-A-225/9; OR TYPE 7075-T7351 ALUMINUM ALLOY BAR PER AMS 4124. /2/2/ HEAT TREATMENT:a. DASH AS CODE LETTER - SEE HARDNESS REQUIREMENT PER PROCUREMENT SPECIFICATION.b. CODE LETTERS D AND W - SEE ELECTRICAL CONDUCTIVITY AND HARDNESS REQUIREMENT PER PROCUREMENT SPECIFICATION.c. OTHER CODE LETTERS - NONE
10、.TABLE 1A - DIMENSIONSBASIC NO.AS5164/13/SIZE CODE(NOMINALTUBESIZE)T THREADPERAS8879CLASS 3AA.023C.005D.005 EF.00104 .250 .4375-20 UNJF 1.023 .692 .474 .562 .43905 .312 .5000-20 UNJF 1.023 .755 .536 .625 .50106 .375 .5625-18 UNJF 1.085 .817 .599 .750 .56408 .500 .7500-16 UNJF 1.335 1.005 .786 .937 .
11、75110 .625 .8750-14 UNJF 1.491 1.130 .911 1.125 .87612 .750 1.0625-12 UNJ 1.648 1.318 1.099 1.375 1.06316 1.000 1.3125-12 UNJ 1.866 1.568 1.349 1.687 1.313TABLE 1B - DIMENSIONS AND WEIGHTSBASIC NO.AS5164/13/SIZE CODE GH.010 K VLB/EAAPPROX.REFALLB/EAAPPROX.REFSTEELLB/EAAPPROX.REFTI04 .437 .750 .375 .
12、797- .815 .0268 .0770 .042505 .437 .750 .500 .797- .815 .0221 .0633 .034906 .500 .875 .500 .985-1.003 .0387 .111 .061408 .500 1.125 .750 1.173-1.191 .0627 .180 .099410 .625 1.375 .812 1.355-1.380 .0989 .284 .15712 .625 1.625 1.000 1.668-1.693 .163 .469 .25916 .812 2.125 1.500 2.042-2.072 .269 .772 .
13、426AEROSPACE STANDARD AS5164 SHEET 3 OF 3 REV. A FITTING, CONNECTOR, MULTIPLE FLUID PRESSURE LINE, 45 3. FINISH:a. DASH AS CODE LETTER - CADMIUM PLATE PER QQ-P-416, TYPE II, CLASS 2, DYE BLACK AND COAT WITH A LIGHT FILM OF OIL PER PROCUREMENT SPECIFICATION.b. CODE LETTER D - ANODIZE PER AMS 2472 OR
14、MIL-A-8625, TYPE II, CLASS 2, DYE BLUE, DUPLEX SEAL PER PROCUREMENT SPECIFICATION.c. CODE LETTERS J, K, AND R - PASSIVATE PER AMS-QQ-P-35, TYPE VI OR VII.d. CODE LETTER T - ANODIZE PER AMS 2488 OR FLUORIDE PHOSPHATE CONVERSION COAT PER AMS 2486 WITH COLOR PER PROCUREMENT SPECIFICATION.e. CODE LETTER
15、 W - ANODIZE PER MIL-A-8625, TYPE II, CLASS 2, DYE BROWN, DUPLEX SEAL PER PROCUREMENT SPECIFICATION./4/ PROCUREMENT SPECIFICATION: AS4875/1 EXCEPT AS SPECIFIED ON THIS STANDARD. USERS OF THIS STANDARD SHALL PROCURE THIS PRODUCT FROM ACCREDITED MANUFACTURER(S) OR ACCREDITED DISTRIBUTOR(S) AS LISTED I
16、N THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED MANUFACTURERS LIST (QML) FOR THIS TYPE PRODUCT./5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B.a. FOR SIZE 06 AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTERS “AS” AND MATERIAL CODE LETTE
17、R.b. FOR SIZE 08 AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER AND MATERIAL CODE LETTER.6. INTENDED USE: THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH MAXIMUM OPERATING PRESSURES AS FOLLOWS:a. SIZES 04 THROUGH 12 IN ALUMINUM ALLOY AND SIZES 04 THROUGH 16 IN CORROSION RESI
18、STANT STEEL AND TITANIUM ALLOY AT 3000 psi.b. SIZE 16 IN ALUMINUM ALLOY AT 1500 psi.THIS STANDARD IS THE FUNCTIONAL EQUIVALENT OF AN778 AND IS INTENDED TO BE SUITABLE AS A REPLACEMENT STANDARD.7. WHEN MACHINED FROM BAR OR OVERSIZED FORGINGS, THE CENTER BODY SECTION SHALL CONFORM TO AS1376, TABLE 8.8
19、. INTERPRETATION OF DRAWING PER ARP4296.9. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. FORGED SURFACES MAY BE 250 in Ra.10. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED.11. DIMENSIONING AND TOLERANCING:
20、 ASME Y14.5M-1994.12. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS 030./13/ EXAMPLE OF PART NUMBER:14. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT.
