1、 AEROSPACE STANDARD COUPLING COMPONENTS, THREADLESS - FLEXIBLE, FIXED CAVITY, CURRENT CARRYING, SELF BONDING KIT OF PARTS AS7512Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any mean
2、s, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org IS
3、SUED2017-09THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3A FEDERAL SUPPLY CLASS 4730 AS7512 SHEET 1 OF 2 PROCUREMENT SPECIFICATION: AS7510 /4/ SAE Technical Standards Board Rules provide that: “This report is published by SAEtoadvance thestate of technicaland engineering sciences. The useof this report i
4、s entirely voluntary, and its applicability andsuitabilityfor any particularuse, includingany patent infringement arisingtherefrom,is thesole responsibility of theuser.” SAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed, stabilized, or cancelled. SAE
5、invites your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS7512 RATIONALE NEW PART STANDARD AS PART OF AS7510 TO SUPERSEDE AS5835. FIGURE 1 AEROSPACE STANDARD AS7512 SHEET 2 OF 2 COUPLING COMPONENTS, THREA
6、DLESS - FLEXIBLE, FIXED CAVITY, CURRENT CARRYING, SELF BONDING KIT OF PARTS NOTES /1/ MATERIAL: IN ACCORDANCE WITH THE APPLICABLE COMPONENTS STANDARDS. THE COUPLING COMPONENTS SHALL CONSIST OF THE FOLLOWING: MATERIAL CODE LETTER A (ALUMINUM ALLOY) 1. (1) SLEEVE - AS7514 A (SIZE) 2. (1) COUPLING ASSE
7、MBLY - AS7515 A (SIZE) 2. HEAT TREATMENT AND FINISH: IN ACCORDANCE WITH THE APPLICABLE COMPONENTS STANDARDS 3. INTENDED USE: THE AS7512 COUPLING COMPONENTS PART NUMBER IS INTENDED FOR USE AS A DRAWING CALLOUT ON INSTALLATION DRAWINGS. 4. IDENTIFICATION: MARK PER AS478-35D OR AS478-30 USING .062 OR L
8、ARGER CHARACTERS. MARK AS A MINIMUM THE MANUFACTURERS NAME, OR CAGE CODE, COMPLETE “AS” NUMBER AND DATE OF MANUFACTURE IN ACCORDANCE WITH MIL-STD-130. SIZES 20 AND SMALLER MAY BE INDIVIDUALLY BAGGED WITH A TAG PER AS478-35D IN ACCORDANCE WITH THE APPLICABLE COMPONENTS STANDARDS. 5. COUPLING COMPONEN
9、TS SHALL CONSIST OF ONE EACH AS7514( )( ) AND AS7515( )( ) PACKAGED TOGETHER IN ONE BAG. THE BAG CONTAINING THE COUPLING ASSEMBLY PARTS SHALL BE MARKED PER /7/. /6/ COUPLING COMPONENTS SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED AND ASSEMBLED BY AN ACCREDITED MANUFACTURER LISTED IN THE PERF
10、ORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL), PRI-QPL-AS7510 FOR THE INDIVIDUAL COMPONENTS (AS7514 AND AS7515). THE QPL IS AVAILABLE AT www.eAuditN. /7/ FORMAT OF PART NUMBER: AS7512 A 32 BASIC PART NUMBER MATERIAL CODE LETTER /1/ SIZE CODE, TUBE SIZE IN .062 IN INCREMENTS (SEE APPLI
11、CABLE COMPONENT STANDARD) EXAMPLE OF PART NUMBER: AS7512A32 /5/ SPECIFICATION NOTES 1. REVISION INDICATOR: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
