1、 AEROSPACE STANDARD CONNECTORS, ELECTRICAL, RECTANGULAR, RECEPTACLE, CRIMP CONTACTS, (DUAL INSERT, TYPE II, CLASS 1, (-65 C TO +125 C), SERIES 2, SHELL DESIGNATOR A) AS81659/41Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval s
2、ystem or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServ
3、icesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2004-05REVISED2017-06THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.B FEDERAL SUPPLY CLASS 5935 AS81659 /41 SHEET 1 OF 3 REV. B PROCUREMENT SPECIFICATION: AS81659 SAE Technical Standards Board Rules provide that: “This report is published by SAE
4、toadvance thestate of technicaland engineering sciences. The useof this report is entirely voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,is the sole responsibility of theuser.” SAE reviews eachtechnical reportatleast every fi
5、veyears at whichtime it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit HTTP:/STANDARDS.SAE.ORG/AS81659/41B RATIONALE REVISION IS REQUIRED TO UPDATE THE CONNECTOR
6、 INSERT AND INSTALLING/REMOVAL TOOL REFERENCES. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81659. FIGURE 1 - CONNECTOR SUGGESTED PANEL CUTOUT/RECOMMENDED MATED POSITION INCH MM INCH MM INCHES MM INCHES MM INCHE
7、S MM .006 .047 .060 .093 .117 .118 .122 .133 .15 1.19 1.52 2.36 2.97 3.00 3.10 3.38 .178 .198 .225 .235 .281 .297 .521 .541 4.52 5.03 5.72 5.97 7.14 7.54 13.23 13.74 .885 .897 .928 .930 .948 1.367 1.387 1.3915 22.48 22.78 23.57 23.62 24.08 34.72 35.23 35.34 1.427 1.447 1.541 1.648 1.860 2.320 2.440
8、2.450 36.25 36.75 39.14 41.86 47.24 58.93 61.98 62.23 2.783 3.095 3.125 3.296 3.580 3.590 3.845 3.875 70.69 78.61 79.38 83.72 90.93 91.19 97.66 98.43 AEROSPACE STANDARD AS81659 /41 SHEET 2 OF 3 REV. B CONNECTORS, ELECTRICAL, RECTANGULAR, RECEPTACLE, CRIMP CONTACTS, (DUAL INSERT, TYPE II, CLASS 1, (-
9、65 C TO +125 C), SERIES 2, SHELL DESIGNATOR A) FIGURE 2 - CONNECTOR CONFIGURATIONS AND DIMENSIONS AEROSPACE STANDARD AS81659 /41 SHEET 3 OF 3 REV. B CONNECTORS, ELECTRICAL, RECTANGULAR, RECEPTACLE, CRIMP CONTACTS, (DUAL INSERT, TYPE II, CLASS 1, (-65 C TO +125 C), SERIES 2, SHELL DESIGNATOR A) FIGUR
10、E 2 - CONNECTOR CONFIGURATIONS AND DIMENSIONS (CONTINUED) REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81659. 1. DESIGN: CONNECTOR ACCESSORIES SHALL BE DESIGNED IN ACCORDANCE WITH FIGURES 1 AND 2. DIMENSIONS ARE IN INCHES AND APPLY AFTER PLATING. METRIC EQU
11、IVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1 INCH = 25.4 MM. NORMAL (01) POLARIZATION POSITION SHOWN, FOR ALTERNATE POSITIONS, SEE AS81659. FOR LOCATION OF DATUMS G AND H, REFER TO AS81659, FIGURE 10. 2. INSERT ARRANGEMENTS SHALL BE IN ACCORDANCE WITH AS31571. 3. CONTACTS SHA
12、LL BE IN ACCORDANCE WITH AS39029/11 OR AS39029/12, AS APPLICABLE. 4. INSTALLING AND REMOVAL TOOLS SHALL BE IN ACCORDANCE WITH AS81969/1 OR AS81969/14. SPECIFICATION NOTES 1. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TEC
13、HNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
