1、 AEROSPACE STANDARD TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, BUSSING MODULES, FEEDBACK TYPE, SERIES II AS81714/61Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by a
2、ny means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae
3、.org ISSUED 2004-04REAFFIRMED 2012-01THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5940 AS81714/61SHEET 1 OF 5 SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirel
4、y voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites y
5、ourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81714/61 RATIONALE AS81714/61 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S
6、. MILITARY SPECIFICATION MIL-T-81714/61A, NOTICE 1, NOTICE 2 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-T-81714/61A, NOTICE 1,
7、NOTICE 2. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT S
8、PECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. UNDER DEPARTMENT OF DEFENSE POLICI
9、ES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS TECHNICAL REPORT. AEROSPACE STANDARD AS81714/61SHEET 2 OF 5 TERMI
10、NAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, BUSSING MODULES, FEEDBACK TYPE, SERIES II THIS SPECIFICATION IS APPROVED FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE. THE COMPLETE REQUIREMENTS FOR ACQUIRING THE BLOCK DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT A
11、ND THE LATEST ISSUE OF SPECIFICATION MIL-T-81714. FIGURE 1. BLOCK SIZE 0W, 0X, 0Z. MIL-T-81714/61A REMAINS INACTIVE FOR NEW DESIGN, HOWEVER, THE DOCUMENT IS VALID FOR USE. AEROSPACE STANDARD AS81714/61SHEET 3 OF 5 TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, BUSSING MODULES, FEEDBA
12、CK TYPE, SERIES II FIGURE 2. BLOCK SIZE 0Y. AEROSPACE STANDARD AS81714/61SHEET 4 OF 5 TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, BUSSING MODULES, FEEDBACK TYPE, SERIES II FIGURE 3. COMPONENT DESIGNATOR. TABLE 1. DIMENSIONS. COMPONENT DESIGNATOR CONTACT SIZE BUS/CONTACT DESCRIPTIO
13、N A MAX B MAX 0Z 12/16 ONE BUS - 2 SIZE 12 & 6 SIZE 16 1.047 .977 0Y 16/20 ONE BUS - 2 SIZE 16 & 6 SIZE 20 .920 .880 0X 12/16 2 BUSES - 1 SIZE 12 & 3 SIZE 16 PER BUS 1.047 .977 0W 16, 20 & 22 5 BUSES - 1 SIZE 22, 1 SIZE 20 & 1 SIZE 16 PER BUS 1.047 .890 TABLE 2. COMPONENT DESIGNATOR CONTACT SIZE INS
14、ERTING/REMOVAL TOOL END SEAL PLUG BLOCK REMOVAL TOOL 0W 16 20 22 M81969/14-03 M81969/14-10 M81969/14-07 MS27488-16 MS27488-20 MS27488-22 M81714/69-02 0Y 16 20 M81969/14-03 M81969/14-10 MS27488-16 MS27488-20 M81714/69-01 0Z 12 16 M81969/16-03/8-10 M81969/14-03 MS27488-12 MS27488-16 M81714/69-02 0X 12
15、 16 M81969/16-03/8-10 M81969/14-03 MS27488-12 MS27488-16 M81714/69-02 INCH MM INCH MM INCH MM INCH MM .005 .006 .007 .010 .012 .016 .018 .030 .035 0.12 0.15 0.17 0.25 0.30 0.40 0.45 0.76 0.88 .040 .083 .093 .110 .130 .170 .180 .189 .202 1.01 2.10 2.36 2.79 3.30 4.31 4.57 4.80 5.13 .214 .225 .226 .25
16、0 .315 .510 .518 .630 5.43 5.71 5.74 6.35 8.00 12.95 13.15 16.00 .672 .720 .880 .890 .920 .997 1.020 1.047 17.06 18.18 22.35 22.61 23.37 24.82 25.90 26.59 AEROSPACE STANDARD AS81714/61SHEET 5 OF 5 TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, BUSSING MODULES, FEEDBACK TYPE, SERIES I
17、I NOTES: 1. DIMENSIONS ARE IN INCHES. 2. METRIC EQUIVALENTS (TO THE NEAREST .01 MM) ARE FOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1 INCH = 25.4 MM. 3. BLOCK IS DESIGNED FOR INSTALLATION IN MIL-T-81714/67 RACKS OR MIL-T-81714/68 BRACKETS. 4. THE PART NUMBER CONSISTS OF THE LETTER M, SPECIFICATION SHEET NUMBER AND COMPONENT DESIGNATOR.
