1、 AEROSPACE STANDARD TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, WIRE IN-LINE JUNCTIONS, SERIES II AS81714/65Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means
2、 electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISS
3、UED 2004-04REAFFIRMED 2012-01THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5940 AS81714/65SHEET 1 OF 4 SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely volunt
4、ary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwritt
5、encomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81714/65 RATIONALE AS81714/65 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITA
6、RY SPECIFICATION MIL-T-81714/65, AMENDMENT 1, NOTICE 2 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-T-81714/65, AMENDMENT 1, NOTI
7、CE 2. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECI
8、FICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. UNDER DEPARTMENT OF DEFENSE POLICIES A
9、ND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS AEROSPACE STANDARD AS81714/65SHEET 2 OF 4 TERMINAL JUNCTION SYSTEM, T
10、ERMINAL JUNCTION BLOCKS, SECTIONAL, WIRE IN-LINE JUNCTIONS, SERIES II THIS SPECIFICATION IS APPROVED FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE. THE COMPLETE REQUIREMENTS FOR ACQUIRING THE SPLICES DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF SPECI
11、FICATION MIL-T-81714. FIGURE 1. WIRE IN-LINE JUNCTION TYPE: 2. PART NUMBER COMPONENT DESIGNATOR A MAX B MAX C MAX D REF M81714/65-22-2 22 1.322 (33.58) .240 (6.05) .384 (9.75) .120 (3.05) M81714/65-20-2 20 1.428 (36.27) .271 (6.88) .481 (12.22) .150 (3.81) M81714/65-16-2 16 1.428 (36.27) .304 (7.72)
12、 .548 (13.92) .184 (4.67) M81714/65-12-2 12 1.704 (43.28) .367 (9.32) .674 (17.12) .247 (6.27) MIL-T-81714/65, DATED 2 MARCH 1988, IS HEREBY REINSTATED AND MAY BE USED FOR ACQUISITION. AEROSPACE STANDARD AS81714/65SHEET 3 OF 4 TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, WIRE IN-LI
13、NE JUNCTIONS, SERIES II FIGURE 2. WIRE IN-LINE JUNCTION SPLICE TYPE: 1. PART NUMBER COMPONENT DESIGNATOR E MAX F MAX M81714/65-22-1 22 1.310 .230 M81714/65-20-1 20 1.434 .290 M81714/65-16-1 16 1.452 .324 M81714/65-12-1 12 1.710 .387 INCH MM INCH MM INCH MM INCH MM .120 .150 .184 .230 .240 .247 3.05
14、3.81 4.67 5.84 6.05 6.27 .271 .290 .304 .324 .367 .384 6.88 7.37 7.72 8.23 9.32 9.75 .387 .481 .548 .674 1.310 1.322 9.83 12.22 13.92 17.12 33.27 33.58 1.428 1.403 1.434 1.452 1.704 36.27 35.64 36.42 36.88 43.28 AEROSPACE STANDARD AS81714/65SHEET 4 OF 4 TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BL
15、OCKS, SECTIONAL, WIRE IN-LINE JUNCTIONS, SERIES II NOTES: 1. DIMENSIONS ARE IN INCHES. 2. HOUSING MAY BE METAL. 3. EACH WIRE IN-LINE JUNCTION (TYPE 1) IS SUPPLIED WITH TWO (2) CONTACTS AND NO SEALING PLUG. EACH WIRE IN-LINE JUNCTION (TYPE 2) IS SUPPLIED WITH FIVE (5) CONTACTS AND ONE (1) SEALING PLU
16、G. CONTACT INSERTING/REMOVAL TOOLS ARE TO BE ORDERED SEPARATELY, AS REQUIRED. NO END SEALING PLUGS REQUIRED WITH TYPE 1. 4. METRIC EQUIVALENTS (TO THE NEAREST .01 MM) ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1 INCH = 25.4 MM. 5. THE PART NUMBER CONSISTS OF THE LETTER M, SPECIFICATION SHEET NUMBER, COMPONENT DESIGNATOR AND WIRE IN-LINE JUNCTION TYPE (1 = SINGLE, 2 = DOUBLE).
