1、Copyright 2002 Society of Automotive Engineers, Inc. Printed in the U.S.A.All rights reserved.TO PLACE A DOCUMENT ORDER: (724) 776-4970 FAX: (724) 776-0790 SAE WEB ADDRESS: http:/www.sae.org400 Commonwealth Drive, Warrendale, PA 15096-0001SAE Technical Standards Board Rules providethat: “This report
2、 is published by SAE to advancethe state oftechnical and engineering sciences.Theuse ofthis reportisentirelyvoluntary, andits applicabilityand suitabilityfor any particularuse,including any patentinfringement arising therefrom,isthe sole responsibility of the user.”SAE reviews each technical reporta
3、tleastevery five years atwhich timeitmay bereaffirmed,revised, or cancelled.SAE invites yourwritten comments and suggestions.SHEET 1 OF 4AS81765/7THIRD ANGLE PROJECTIONAEROSPACE STANDARDAS81765/7ISSUED 2002-02INSULATING COMPONENTS, MOLDED,ELECTRICAL, HEAT SHRINKABLE FLUOROPOLYMERCOMPOSITE, SEMI-RIGI
4、D, CROSSLINKED CUSTODIAN: SAE AE-8FEDERAL SUPPLY CLASS 5970NOTICETHIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-I-81765/7 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS
5、. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-I-81765/7. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED.THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULA
6、TIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SP
7、ECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS
8、SAE TECHNICAL DOCUMENT.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-400 Commonwealth Drive, Warrendale, PA 15096-0001INSULATING COMPONENTS, MOLDED,ELECTRICAL, HEAT SHRINKABLE FLUOROPOLYMERCOMPOSITE,
9、 SEMI-RIGID, CROSSLINKEDAEROSPACE STANDARDAS81765/7SHEET 2 OF 4AS81765/7THIS SPECIFICATION IS APPROVED FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE.THE COMPLETE REQUIREMENTS FOR PROCURING THE INSULATING COMPONENTS DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE ISSUE
10、IN EFFECT OF MIL-I-81765.REQUIREMENTS:CONTINUOUS OPERATING TEMPERATURE RANGE: -55C (-67F) TO + 150C (+302F)COLOR: UNLESS OTHERWISE SPECIFIED, MOLDED COMPONENTS FABRICATED TO THE REQUIREMENTS HEREIN SHALL BE FURNISHED IN BLACK.PROPERTIES: PROPERTIES SHALL BE IN ACCORDANCE WITH TABLE I.TABLE I. PHYSIC
11、AL PROPERTIESCopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-400 Commonwealth Drive, Warrendale, PA 15096-0001INSULATING COMPONENTS, MOLDED,ELECTRICAL, HEAT SHRINKABLE FLUOROPOLYMERCOMPOSITE, SEMI-RIGI
12、D, CROSSLINKEDAEROSPACE STANDARDAS81765/7SHEET 3 OF 4AS81765/7TABLE I (CONTINUED)Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-400 Commonwealth Drive, Warrendale, PA 15096-0001INSULATING COMPONENTS,
13、MOLDED,ELECTRICAL, HEAT SHRINKABLE FLUOROPOLYMERCOMPOSITE, SEMI-RIGID, CROSSLINKEDAEROSPACE STANDARDAS81765/7SHEET 4 OF 4AS81765/7SHELF LIFE (AS SUPPLIED): THE MANUFACTURER SHALL CERTIFY IN WRITING THAT THE MOLDED COMPONENTS, AFTER STORAGE AT A TEMPERATURE OF 18 TO 35C (65 TO 95F) FOR A PERIOD OF TW
14、O YEARS, SHALL CONFORM TO THE DIMENSIONAL REQUIREMENTS SPECIFIED HEREIN AND IN THE CONTRACT OF PURCHASE ORDER.NOTE 1: MOLDED SLABS AS DESCRIBED IN 4.5.2 CANNOT READILY BE PREPARED FROM THIS COMPOSITE MATERIAL, THEREFORE, TEST SPECIMENS MAY BE PREPARED DIRECTLY FROM A SELECTED MOLDED COMPONENT OF SUITABLE SIZE AND GEOMETRY.NOTE 2: FLUID IMMERSION CONDITIONS:Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-
