1、AEROSPACE STANDARD INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE III, CLASS 2, COMPOSITION C AS81969/1Copyright 2011 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, elec
2、tronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 20
3、11-12THIRD ANGLE PROJECTION CUSTODIAN: AE-8C2 FEDERAL SUPPLY CLASS 5120 AS81969/1SHEET 1 OF 3PROCUREMENT SPECIFICATION: AS81969SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely vol
4、untary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwr
5、ittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81969/1RATIONALE AS81969/1 PERMITS THE CANCELLATION AND SUPERSESSION OF MIL-I-81969/1 WITH THIS DOCUMENT. IT INCLUDES ENGINEERING POSITION LETTERS, M
6、ILITARY SPECIFICATION AMENDMENTS, AND MINOR TECHNICAL CHANGES REQUIRED TO REFLECT THE APPROVED QUALIFIED TOOLS. GOVERNMENT DOCUMENTATION REFERENCES ARE REMOVED. NOTICE THE REQUIREMENTS FOR PROCURING THE TOOLS AND ACCESSORIES DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE O
7、F: SAE AS81969 4.100 MAXREMOVALTIP.450 MIN1.000.940PART NUMBER & MFR NAME(LOCATION OPTIONAL)INSTALLING TIP.400 SQ.360ABSEE DETAIL A.200 MIN.010 MAXLANCEF SLOTEC .030.020DETAIL A.072.052.138.118.105.085DA DC.157.137BODY DESIGN OPTIONAL1.000.940.450 MINFIGURE 1 M81969-01 AND -04 TOOLS Copyright SAE In
8、ternational Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS81969/1SHEET 2 OF 3INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE III, CLASS 2, COMPOSITION C REMOVALTIP.450 MIN1.000.940PART NU
9、MBER & MFR NAME(LOCATION OPTIONAL)INSTALLING TIP.400 SQ.360ABSEE DETAIL A.200 MIN.010 MAXLANCEF SLOTEC .030.020DETAIL ADC.157.137.159.139DABODY DESIGN OPTIONAL(SIZE -03 ONLY).065.055(SIZE -02 ONLY)4.100 MAX1.000.940.450 MINFIGURE 2 M81969-02 AND -03 TOOLS TABLE 1 TOOL CONFIGURATION PART NO. M81969/1
10、 CONTACT SIZEINSTALLING TOOL REMOVAL TOOL BODY COLOR CODE FIGNO. A B DA C E DC F INSTALL TIPREMOVAL TIP-01 22 .065 .063.052.048.044.037.074.070.055.053.047.037.030.020GREEN WHITE 1-02 20 .085 .081.072.068N/A.087.085.072.068.065.055.035.025RED 2 -03 16 .134 .128.114.112.077.067.136.134.116.112.077.06
11、7.060.045BLUE 2 -04 22D .065 .063.052.048.044.037.065.063.053.048.045.040.030.020GREEN 1 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS81969/1SHEET 3 OF 3INSTALLING AND REMOVAL
12、 TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE III, CLASS 2, COMPOSITION C REQUIREMENTS: AS SPECIFIED IN AS81969 1. CONFIGURATION: UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES. OUTLINE CONFIGURATION OPTIONAL WITHIN MAXIMUM DIMENSIONS SHOWN. HEIGHT DA AND DC ARE MEASURED AT THE START OF ANGLE UP
13、TO THE BODY SECTION AND ARE THE LOCATION POINTS FOR THE .450 MIN DIMENSION. 2. MARKING: EACH TOOL SHALL BE LEGIBLY AND PERMANENTLY MARKED ON TOOL BODY WITH MANUFACTURER IDENTIFICATION AND PART NUMBER IN ACCORDANCE WITH MIL-STD-130 (LOCATION OPTIONAL). MANUFACTURER SYMBOL, IF USED, SHALL BE ACCORDANC
14、E WITH AIR1351. 3. MATERIALS (SEE AS81969): TOOL BODY SHALL BE ACETAL OR APPROVED EQUIVALENT. TOOL TIPS SHALL BE STAINLESS STEEL OR STEEL TREATED TO RESIST CORROSION. 4. PLATING: NOT APPLICABLE. 5. DESIGN: SLOT DESIGN SHALL ALLOW FOR ALL APPLICABLE WIRE SIZES TO FIT INTO TOOL. 6. PLUNGER FORCE: NOT
15、APPLICABLE. 7. PART NUMBER M81969 /1r01 I I I I I I_DASHNUMBER(SEETABLE1) I I_DETAILSPECIFICATIONNUMBER I_BASICSPECIFICATIONNUMBERAPPLICATIONNOTES:1. TOOLSAREUSEDTOINSTALLANDREMOVECONTACTSFROMMILrDTLr24308,SIZES22DAND20ANDAS81659CONNECTORS,SERIES2.2. AS81969/1SUPERSEDESMILrIr81969/1WHICHSUPERSEDEDMS
16、3156(NAVY)ANDMILrCr24308/18.TABLE 2 SUPERSEDING PART NUMBERS PARTNO.M81969/1SUPERSEDEDPARTNO.r01 MS3156r22r02 MS3156r20M24308/18r2r03 MS3156r16M24308/18r3r04 M24308/18r1Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
