1、AEROSPACE STANDARD INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE I, CLASS 1, COMPOSITION A AS81969/33Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, elect
2、ronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 201
3、4-07THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120 AS81969/33SHEET 1 OF 3PROCUREMENT SPECIFICATION: AS81969SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineeringsciences.The useofthis reportisentirelyvol
4、untary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwri
5、ttencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81969/33RATIONALE AS81969/33 PERMITS THE CANCELLATION AND SUPERSESSION OF MIL-I-81969/33 WITH THIS DOCUMENT. IT INCLUDES MILITARY SPECIFICATION AMENDM
6、ENTS, AND MINOR TECHNICAL CHANGES REQUIRED TO REFLECT THE APPROVED QUALIFIED TOOLS. GOVERNMENT DOCUMENTATION REFERENCES ARE REMOVED. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. TOOL VIEW PROBE REVERSE TOP
7、 VIEW PROBE REVERSE END VIEW PROBE REVERSE SIDE VIEW DETAIL “A” FIGURE 1 - M81969/33-01 INLINE REMOVAL TOOL AEROSPACE STANDARD AS81969/33SHEET 2 OF 3INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE I, CLASS 1, COMPOSITION A TOOL VIEW REVERSE PROBE VIEW DETAIL A TOP VIEW DETAIL A SIDE
8、 VIEW DETAIL B PROBE TIP VIEW DETAIL C PROBE TIP END VIEW FIGURE 2 - M81969/33-02 ANGLE REMOVAL TOOL AEROSPACE STANDARD AS81969/33SHEET 3 OF 3INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE I, CLASS 1, COMPOSITION A REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND T
9、HE LATEST ISSUE OF AS81969. 1. CONFIGURATION: TOOL CONFIGURATION SHALL BE IN ACCORDANCE WITH FIGURES 1 AND 2. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED TOLERANCE IS .005 ON THREE PLACE DECIMALS, .01 ON TWO PLACE DECIMALS AND 4q.HANDLE CONFIGURATION OPTIONAL WITHIN MAXIMUM DIMENSIONS SHOWN
10、 EACH TOOL SHALL BE FURNISHED WITH A PROTECTIVE PROBE CAP. THE CAP DESIGN AND MATERIAL IS OPTIONAL (SEE APPLICATION NOTE). TOOL SHALL BE FREE FROM NICKS OR BURRS. 2. MATERIAL: HANDLE SHALL BE ALUMINUM OR PLASTIC (RED COLOR). PROBE SHALL BE ASTM TYPE A2 TOOL STEEL HARDENED TO ROCKWELL C 48-50 (POLIS
11、HED) OR STAINLESS STEEL (410 OR 420) ROCKWELL HARDEN C 40-45. PROBE SHALL BE FREE FROM NICKS OR BURRS. 3. IDENTIFICATION MARKING: EACH TOOL SHALL BE LEGIBLY AND PERMANENTLY MARKED ON TOOL HANDLE IN ACCORDANCE WITH MIL-STD-130 (LOCATION OPTIONAL). HANDLE SHALL BE RED. SUPPLIER SYMBOL, IF USED, SHALL
12、BE IN ACCORDANCE WITH AIR1351. MARKING SHALL INCLUDE MANUFACTURER NAME OR SYMBOL, MANUFACTURER PART NUMBER, AND AS81969/33 PIN. 4. PART IDENTIFICATION NUMBER (PIN) M81969 /33 -01 I I I I I I_ DASH NUMBER (-01 AND -02) I I_ DETAIL SPECIFICATION NUMBER I_ BASIC SPECIFICATION NUMBER APPLICATION NOTES:
13、1. TOOLS SHALL BE USED TO INSTALL CONTACTS IN CONNECTORS SPECIFIED IN TABLE 1. TABLE 1 - TOOL APPLICATION AND SUPERSEDING SPECIFICATIONS PART NUMBER M81969/33 APPLICABLE CONNECTOR (CRIMP CONTACT) SPECIFICATIONS SUPERSEDED TOOL SPECIFICATIONS -01 THRU -02 MIL-DTL-28840 MIL-I-81969/33A(EC) 1/ MIL-I-81
14、969/33A(EC) ADM 1 1/ AS81969/19 SUPERSEDED MIL-I-81969 WITHOUT PART NUMBER CHANGE 2. THE PROTECTIVE CAP (SEE FIGURES 1 AND 2) MINIMIZES DAMAGE TO THE TIP AND IMPROVES PERSONNEL SAFETY. IF LOST, CONTACT THE SUPPLIER FOR REPLACEMENT. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN
15、IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
