1、 AEROSPACE STANDARD REMOVAL TOOLS, SOCKET HEAD, ELECTRONIC COMPONENTS, TYPE II, CLASS 1, COMPOSITION C AS81969/43Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic,
2、mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2015-07THI
3、RD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120AS81969/43 SHEET 1 OF 2 PROCUREMENT SPECIFICATION: AS81969SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is entirelyvolun
4、tary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwritte
5、ncomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81969/43 RATIONALE THIS DETAIL SPECIFICATION SHEET IS REQUIRED TO ALLOW THE CANCELLATION AND SUPERSESSION OF MIL-I-81969/43 WITH THIS DOCUMENT, TO UPDATE
6、 QUALIFICATION INFORMATION, TO REMOVE GOVERNMENT JARGON, TO IMPROVE DRAWING LEGIBILITY, AND TO UPDATE REFERENCES. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. FIGURE 1 - REMOVAL TOOL -01 AND -02 CONFIGURAT
7、IONS AND DIMENSIONS AEROSPACE STANDARD AS81969/43 SHEET 2 OF 2 REMOVAL TOOLS, SOCKET HEAD, ELECTRONIC COMPONENTS, TYPE II, CLASS 1, COMPOSITION C TABLE 1 - METRIC EQUIVALENTS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS .003 0.076 .064 1.63 .287 7.29 .015 0.381 .065 1.65 .625 15.88 .020
8、0.508 .066 1.68 .750 19.05.036 0.914 .067 1.70 1.200 30.48 .037 0.940 .135 3.43 1.300 33.02.045 1.143 .155 3.94 1.875 47.63 .046 1.168 .240 6.10 2.000 50.80.050 1.270 .250 6.35 REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. 1. DESIGN: THE TOOL SHALL BE
9、 DESIGNED IN ACCORDANCE WITH FIGURES 1 AND 2. DIMENSIONS ARE IN INCHES. METRIC EQUIVALENTS IN TABLE 1 ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MILLIMETERS. UNLESS OTHERWISE SPECIFIED, TOLERANCE IS .005 INCH (0.13 MILLIMETERS). 2. MATERIAL AND FINISHES: TORRINGTON HEADED
10、PIN - TOOL STEEL IN ACCORDANCE WITH AS81969. INSULATION - POLYOLEFIN HEAT SHRINKABLE TUBING (RED). TUBING - 304 STAINLESS STEEL HALF HARD TEMPER. 3. PART NUMBER/MARKING: M81969/43-01 FOR USE WITH MIL-DTL-83505/6-001, -002, AND -003 M81969/43-02 FOR USE WITH MIL-DTL-83505/6-004 EACH TOOL SHALL BE LEG
11、IBLY AND PERMANENTLY MARKED ON THE HANDLE WITH THE MANUFACTURERS IDENTIFICATION AND PART NUMBER IN ACCORDANCE WITH MIL-STD-130. MANUFACTURER SYMBOL, IF USED, SHALL BE IN ACCORDANCE WITH AIR1351. 4. QUALIFICATION: QUALIFICATION SHALL BE IN ACCORDANCE WITH AS81969 WITH THE FOLLOWING EXCEPTIONS: ROTATI
12、ON AND THRUST - NOT APPLICABLE ALTERNATIVE QUALIFICATION REQUIREMENTS SUCH AS CERTIFICATION, FIRST ARTICLE OR QC TESTING MAY BE IMPOSED BY THE QUALIFYING ACTIVITY (QA). THE QA SHALL SUBMIT A WRITTEN REQUEST TO THE AE-8C2 COMMITTEE FOR REVIEW AND APPROVAL OF THE ALTERNATIVE QUALIFICATION TESTING PROG
13、RAM PRIOR TO IMPLEMENTATION OF THE REQUIREMENT. APPLICATION NOTES: 1. THIS TOOL SHALL BE USED TO REMOVE THE APPLICABLE CONTACTS FROM MIL-DTL-83505/6 AS SPECIFIED IN TABLE 2. 2. THIS DOCUMENT SUPERSEDES MIL-I-81969/43B DATED 28 JUNE 1993. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT M
14、ARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
