1、AEROSPACE STANDARDINSTALLING AND REMOVAL TOOLS, CONNECTORELECTRICAL CONTACT, TYPE I 410, 416 STAINLESS STEEL, 300 MARAGING STEEL, OR MARSTENITIC STEEL.PROBES: SAE 4130, AMS5643, AMS6370, 410 STEEL, 416 STAINLESS STEEL, 300 MARAGING STEEL, OR CROLOY 16-6PH. PROBES SHALL BE HEAT TREATED TO ROCKWELL RC
2、 35-45. FOR MATERIAL TOO THIN FOR ACCURATE ROCKWELL MEASUREMENT, THE KNOOP HARDNESS SCALE SHALL BE USED. KNOOP HARDNESS (500 GRAM LOAD MINIMUM) SHALL BE350-460.4. PLATING: FOR NON-CORROSION RESISTANT STEEL, ELECTROLESS NICKEL IN ACCORDANCE WITH AMS-C-26074.5. PLUNGER FORCE: NOT APPLICABLE.6. PART NU
3、MBERM81969 /8 -01I I II I I_DASH NUMBER (SEE TABLES 1 AND 2)I I_ DETAIL SPECIFICATION NUMBERI_ BASIC SPECIFICATION NUMBERAEROSPACE STANDARDAS81969/8SHEET 7 OF 8REV.AINSTALLING AND REMOVAL TOOLS, CONNECTORELECTRICAL CONTACT, TYPE I & II, CLASS 2,COMPOSITION AAPPLICATION NOTES:1. APPLICATION AND SUPER
4、SESSION DATA: THESE TOOLS SHALL BE USED TO INSTALL CONTACTS IN CONNECTORS SPECIFIEDIN TABLE 3.TABLE 3 - TOOL APPLICATIONSCONTACTSIZECONTACT INSTALLING TOOLS FOR APPLICABLE CONNECTORSMIL-DTL-38999MIL-DTL-55302/68, /69, /166 THROUGH /171AS81714 (SIZE 22D)MIL-DTL-83733 (SIZE 22D)AS50151 (SERIES AS34501
5、)MIL-DTL-26482 (SERIES 2)AS81703 (SERIES III)AS81714 (EXCEPT 22D)MIL-DTL-83723MIL-DTL-83733 (EXCEPT 22D)ANGLE PROBE TOOLS INLINE PROBE TOOLS ANGLE PROBE TOOL23 M81969/8-15M81969/8-16 M81969/8-315M81969/8-316 -22D22MM81969/8-01M81969/8-02M81969/8-301M81969/8-302 -22 M81969/8-03M81969/8-04 M81969/8-30
6、3M81969/8-304 -20 M81969/8-05M81969/8-06 M81969/8-305M81969/8-306 M81969/8-205M81969/8-20616 M81969/8-07M81969/8-08 M81969/8-307M81969/8-308 M81969/8-207M81969/8-20812 M81969/8-09M81969/8-10 M81969/8-309M81969/8-310 M81969/8-209M81969/8-21010 M81969/8-11M81969/8-12 M81969/8-311M81969/8-312 -8 M81969
7、/8-13M81969/8-14 M81969/8-313M81969/8-314 -2. INLINE PROBE TOOLS ARE INTENDED TO BE USED ON MIL-DTL-38999 CONNECTORS, LANYARD RELEASE VERSIONS AND CONNECTORS WHERE ACCESS TO THE SEALING GROMMET/CONTACTS IS RESTRICTED (I.E., RAIL LAUNCH MOUNTEDCONNECTORS).3. AS81969/8 SUPERSEDES MIL-I-81969/8B. PART
8、NUMBERS REMAIN UNCHANGED. PREVIOUS SUPERSEDED MILITARY SPECIFICATION PART NUMBERS ARE SHOWN IN TABLE 4.TABLE 4 - SUPERSEDING PART NUMBERSCONTACT SIZE SAE PART NUMBERS SUPERSEDED PART NUMBERS22D22MM81969/8-01M81969/8-02M55302/79-01M27495A22MM55302/79-02M27495R22M22 M81969/8-03M81969/8-04 M27495A22M27
9、495R2220 M81969/8-05M81969/8-06 M27495A20M27495R2016 M81969/8-07M81969/8-08 M27495A16M27495R1612 M81969/8-09M81969/8-10 M27495A12M27495R1210 M81969/8-11M81969/8-12 -8 M81969/8-13M81969/8-14 -4. THE PROTECTIVE CAP (SEE FIGURE 1) MINIMIZES DAMAGE TO THE TIP AND IMPROVES PERSONNEL SAFETY. IF LOST, CONT
10、ACT THE SUPPLIER FOR REPLACEMENT.AEROSPACE STANDARDAS81969/8SHEET 8 OF 8REV.AINSTALLING AND REMOVAL TOOLS, CONNECTORELECTRICAL CONTACT, TYPE I & II, CLASS 2,COMPOSITION ASPECIFICATION NOTES:1. REVISION INDICATOR: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCAT
11、ING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR INDOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
