1、 AEROSPACE STANDARD BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, PD SHANK, CORROSION AND HEAT RESISTANT ALLOY, UNS N07001, 165 KSI MIN, .1900-32 UNJF-3A AS9696Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or
2、transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.or
3、g SAE WEB ADDRESS: http:/www.sae.org ISSUED1999-08REVISED 2017-07THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.F FEDERAL SUPPLY CLASS 5306 AS9696 SHEET 1 OF 2 REV. F PROCUREMENT SPECIFICATION: AS7471 /3/ SAE Technical Standards Board Rules provide that: “This report is published by SAEtoadvance thestat
4、e of technicaland engineering sciences. The useof this report is entirely voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,is thesole responsibility of theuser.” SAE reviews eachtechnical reportatleast every fiveyears at whichti
5、me it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS9696F RATIONALE DELETE RADIUS AT TRANSITION OF WRENCH FLATS AND BASE FLANGE, ADD N
6、EW INVENTORY DISPOSITION NOTE, UPDATE FPI REQUIREMENTS, ADD DIAMETER SYMBOL TO STRAIGHTNESS FEATURE CONTROL FRAME, RELOCATE MARKING REQUIREMENTS FROM PREVIOUS NOTE 7 TO FIGURE 1, DRAWING NOTE 3 REVISED FOR CLARITY, DRAWING NOTE 5 DELETED, GENERAL EDITORIAL UPDATE. NOTICE THE INITIAL SAE PUBLICATION
7、OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9696A, NOTICE 1. THIS SAE STANDARD RETAINS THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPLS) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREME
8、NTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1 BOLT AEROSPACE STANDARD AS9696 SHEET 2 OF 2 REV. F BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, PD SHANK, CORROSION AND HEAT RESISTANT ALLOY, UNS N07001, 165 KSI MIN, .1900
9、32 UNJF-3A TABLE 1 PART NUMBERS AND DIMENSIONS PART NUMBER L K APPROX MASS LB/100 PART NUMBER L K APPROX MASS LB/100 MS9696-04 .365 - .385 .072 - .092 .78 MS9696-25 1.678 - 1.698 .998 - 1.058 1.66 MS9696-05 .428 - .448 .072 - .092 .82 MS9696-26 1.740 - 1.760 1.060 - 1.120 1.71 MS9696-06 .490 - .510
10、 .072 - .092 .86 MS9696-27 1.802 - 1.822 1.122 - 1.182 1.75 MS9696-07 .552 - .572 .072 - .092 .90 MS9696-28 1.865 - 1.885 1.185 - 1.245 1.79 MS9696-08 .615 - .635 .072 - .092 .95 MS9696-29 1.990 - 2.010 1.310 - 1.370 1.88 MS9696-09 .678 - .698 .072 - .092 .99 MS9696-30 2.115 - 2.135 1.435 - 1.495 1.
11、96 MS9696-10 .740 - .760 .072 - .120 1.03 MS9696-31 2.240 - 2.260 1.560 - 1.620 2.05 MS9696-11 .802 - .822 .122 - .182 1.07 MS9696-32 2.365 - 2.385 1.685 - 1.745 2.13 MS9696-12 .865 - .885 .185 - .245 1.11 MS9696-33 2.490 - 2.510 1.810 - 1.870 2.21 MS9696-13 .928 - .948 .248 - .308 1.16 MS9696-34 2.
12、615 - 2.635 1.935 - 1.995 2.30 MS9696-14 .990 - 1.010 .310 - .370 1.20 MS9696-35 2.740 - 2.760 2.060 - 2.120 2.38 MS9696-15 1.052 - 1.072 .372 - .432 1.24 MS9696-36 2.865 - 2.885 2.185 - 2.245 2.47 MS9696-16 1.115 - 1.135 .435 - .495 1.28 MS9696-37 2.990 - 3.010 2.310 - 2.370 2.55 MS9696-17 1.178 -
13、1.198 .498 - .558 1.33 MS9696-38 3.115 - 3.135 2.435 - 2.495 2.64 MS9696-18 1.240 - 1.260 .560 - .620 1.37 MS9696-39 3.240 - 3.260 2.560 - 2.620 2.72 MS9696-19 1.302 - 1.322 .622 - .682 1.41 MS9696-40 3.365 - 3.385 2.685 - 2.745 2.81 MS9696-20 1.365 - 1.385 .685 - .745 1.45 MS9696-41 3.490 - 3.510 2
14、810 - 2.870 2.89 MS9696-21 1.428 - 1.448 .748 - .808 1.50 MS9696-42 3.615 - 3.635 2.935 - 2.995 2.98 MS9696-22 1.490 - 1.510 .810 - .870 1.54 MS9696-43 3.740 - 3.760 3.060 - 3.120 3.06 MS9696-23 1.552 - 1.572 .872 - .932 1.58 MS9696-44 3.865 - 3.885 3.185 - 3.245 3.15 MS9696-24 1.615 - 1.635 .935 -
15、 .995 1.62 NOTES /1/ FOR PART NUMBERS MS9696-04 THROUGH MS9696-12, DATUM Z (THREAD PD) SHALL REPLACE DATUM Y. 2. MATERIAL: NICKEL ALLOY PER AMS5708 (UNS N07001). /3/ PROCUREMENT SPECIFICATION: AS7471 EXCEPT COLD ROLLING OF HEAD TO SHANK FILLET RADIUS NOT REQUIRED ON PART NUMBERS MS9696-12 AND SMALLE
16、R. 4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MIN. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 6. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 7. U
17、NLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED. 8. DIMENSIONS ARE IN INCHES. 9. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 10. DO NOT USE UNASSIGNED PA
18、RT NUMBERS. 11. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A CO
19、MPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
