1、 AEROSPACE STANDARD BOLT, SPLINE DRIVE, EXTENDED WASHER, REDUCED SHANK, AMS 5662, METRIC MA4147Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photoc
2、opying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1992-06REAFFIRMED 2013-10THI
3、RD ANGLE PROJECTION CUSTODIAN: E-25 FEDERAL SUPPLY CLASS 5306 MA4147 SHEET 1 OF 13 PROCUREMENT SPECIFICATION: MA3377SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, and
4、its applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwrittencommen
5、ts andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/MA4147 RATIONALE MA4147 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. FIGURE 1 AEROSPACE STANDARD MA4147 SHEET 2 OF 13 BOLT, SPLINE DRIVE, E
6、XTENDED WASHER, REDUCED SHANK, AMS 5662, METRIC TABLE 1AEROSPACE STANDARD MA4147 SHEET 3 OF 13 BOLT, SPLINE DRIVE, EXTENDED WASHER, REDUCED SHANK, AMS 5662, METRIC TABLE 2AEROSPACE STANDARD MA4147 SHEET 4 OF 13 BOLT, SPLINE DRIVE, EXTENDED WASHER, REDUCED SHANK, AMS 5662, METRIC TABLE 2 (CONTINUED)A
7、EROSPACE STANDARD MA4147 SHEET 5 OF 13 BOLT, SPLINE DRIVE, EXTENDED WASHER, REDUCED SHANK, AMS 5662, METRIC TABLE 2 (CONTINUED)AEROSPACE STANDARD MA4147 SHEET 6 OF 13 BOLT, SPLINE DRIVE, EXTENDED WASHER, REDUCED SHANK, AMS 5662, METRIC TABLE 2 (CONTINUED)AEROSPACE STANDARD MA4147 SHEET 7 OF 13 BOLT,
8、 SPLINE DRIVE, EXTENDED WASHER, REDUCED SHANK, AMS 5662, METRIC TABLE 2 (CONTINUED)AEROSPACE STANDARD MA4147 SHEET 8 OF 13 BOLT, SPLINE DRIVE, EXTENDED WASHER, REDUCED SHANK, AMS 5662, METRIC TABLE 2 (CONTINUED)AEROSPACE STANDARD MA4147 SHEET 9 OF 13 BOLT, SPLINE DRIVE, EXTENDED WASHER, REDUCED SHAN
9、K, AMS 5662, METRIC TABLE 2 (CONTINUED)AEROSPACE STANDARD MA4147 SHEET 10 OF 13 BOLT, SPLINE DRIVE, EXTENDED WASHER, REDUCED SHANK, AMS 5662, METRIC TABLE 2 (CONTINUED)AEROSPACE STANDARD MA4147 SHEET 11 OF 13 BOLT, SPLINE DRIVE, EXTENDED WASHER, REDUCED SHANK, AMS 5662, METRIC TABLE 2 (CONTINUED)AER
10、OSPACE STANDARD MA4147 SHEET 12 OF 13 BOLT, SPLINE DRIVE, EXTENDED WASHER, REDUCED SHANK, AMS 5662, METRIC TABLE 2 (CONTINUED)AEROSPACE STANDARD MA4147 SHEET 13 OF 13 BOLT, SPLINE DRIVE, EXTENDED WASHER, REDUCED SHANK, AMS 5662, METRIC NOTES:1. FOR PART NUMBERS WHERE DIMENSION N IS EQUAL TO OR LESS
11、THAN THE THREAD NOMINAL DIAMETER, DATUM A SHALL REPLACE DATUM B.2. MATERIAL: CORROSION AND HEAT RESISTANT NICKEL ALLOY AMS 5662 (UNS N07718).3. HEAT TREATMENT: SOLUTION AND PRECIPITATION TREATED. SEE PROCUREMENT SPECIFICATION.4. HARDNESS: 40 TO 46 HRC.5. FLUORESCENT PENETRANT INSPECTION: PER AMS 264
12、5. ACCEPTANCE CRITERIA PER MA3377.6. PROCUREMENT SPECIFICATION: MA3377.7. SURFACE TEXTURE: SYMBOLS PER ANSI Y14.36-1978. REQUIREMENTS PER ANSI/ASME B46.1-1985 UNLESS OTHERWISE SPECIFIED SURFACES TO BE 3.2 m Ra.8. PART NUMBER SHALL INCLUDE THE STANDARD NUMBER AND THE DASH NUMBER TO INDICATE DIAMETER
13、AND LENGTH. EXAMPLE OF PART NUMBER:a. MA4147-120104 = BOLT, MJ12X1.25 THREAD 104 mm LONG9. SHAPE OF BOTTOM OF HOLE MAY BE CURVED, FLAT, OR ANGULAR AT MANUFACTURERS OPTION WITHIN ENVELOPE SHOWN. NO HOLE IS REQUIRED ON DIAMETER MJ4.10. WRENCHING CONFIGURATION SHALL BE IN ACCORDANCE WITH MA1549. FOR TH
14、E APPLICABLE DASH NUMBER.11. BREAK EDGES 0.1 TO 0.4, UNLESS OTHERWISE SPECIFIED.12. DIMENSION AND TOLERANCING: ANSI Y14.5M-1982, TOLERANCE GRADE PER ANSI B4.2-1978.13. ALL DIMENSIONS IN SI MILLIMETERS UNLESS OTHERWISE SPECIFIED.14. CURVED OR ANGULAR WITHIN ENVELOPE.15. DO NOT USE UNASSIGNED PART NUMBERS.16. MA, AS, AND AMS ARE SAE PUBLICATIONS.17. ANSI IS AMERICAN NATIONAL STANDARDS INSTITUTE PUBLICATION.
