1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA
2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any
3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-22997-9 SANS 105-F09:2009Edition 1ISO 105-F09:2009Edition 1SOUTH AFRICAN NATIONAL STANDARD Textiles Tests for colour fastness Part F09: Sp
4、ecification for cotton rubbing cloth This national standard is the identical implementation of ISO 105-F09:2009, and is adopted with the permission of the International Organization for Standardization. Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X 191 Pretoria 0001
5、Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 105-F09:2009 Edition 1 ISO 105-F09:2009 Edition 1 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee SABS SC 38A, Textile test methods Coloured textiles the PDF-cre
6、ation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2
7、009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the co
8、untry of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedSANS 105-F09:2009This s tandard may only be used and printed by approved subscri
9、ption and freemailing clients of the SABS .ISO 105-F09:2009(E) ISO 2009 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carri
10、ed out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. I
11、SO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare Internati
12、onal Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the el
13、ements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 105-F09 was prepared by Technical Committee ISO/TC 38, Textiles, Subcommittee SC 1, Tests for coloured texiles and colourants. This first edition cancels
14、and replaces Section F09 of the third edition of ISO 105-F (ISO 105-F:1985), which has been technically revised. ISO 105 was previously published in 13 “parts”, each designated by a letter (e.g. “Part A”), with publication dates between 1978 and 1985. Each part contained a series of “sections”, each
15、 designated by the respective part letter and by a two-digit serial number (e.g. “Section A01”). These sections are now being republished as separate documents, themselves designated “parts” but retaining their earlier alphanumeric designations. A complete list of these parts is given in ISO 105-A01
16、. SANS 105-F09:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .SANS 105-F09:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .INTERNATIONAL STANDARD ISO 105-F09:2009(E) ISO 2009
17、All rights reserved 1Textiles Tests for colour fastness Part F09: Specification for cotton rubbing cloth 1 Scope This part of ISO 105 specifies a cotton rubbing cloth which can be used for the assessment of staining in colour fastness to rubbing tests. The staining properties of the cotton rubbing c
18、loth under test are assessed against a cotton rubbing cloth reference fabric, using a cotton dyed reference fabric, both of which are available from a specified source. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated referen
19、ces, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 105-A02, Textiles Tests for colour fastness Part A02: Grey scale for assessing change in colour ISO 105-A05, Textiles Tests for colour fastness Part A05:
20、 Instrumental assessment of change in colour for determination of grey scale rating ISO 105-F02:2009, Textiles Tests for colour fastness Part F02: Specification for cotton and viscose adjacent fabrics ISO 105-J01, Textiles Tests for colour fastness Part J01: General principles for measurement of sur
21、face colour ISO 105-J02, Textiles Tests for colour fastness Part J02: Instrumental assessment of relative whiteness ISO 105-X12, Textiles Tests for colour fastness Part X12: Colour fastness to rubbing ISO 3071, Textiles Determination of pH of aqueous extract ISO 3801, Textiles Woven fabrics Determin
22、ation of mass per unit length and mass per unit area SANS 105-F09:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 105-F09:2009(E) 2 ISO 2009 All rights reserved3 Terms and definitions For the purposes of this document, the following t
23、erms and definitions apply. 3.1 cotton rubbing cloth under test cotton rubbing cloth complying with the requirements in Clause 4 3.2 cotton rubbing cloth reference fabric cotton reference cloth reference fabric complying with the requirements in Clause 4 NOTE Cotton rubbing cloth reference fabric is
24、 only available from Testfabrics Inc., PO Box 26, West Pittston, PA 18643 USA; Tel: +1.570.603-0432; Fax: +1.570.603-0433; email: . 3.3 cotton dyed reference fabric cotton reference fabric complying with ISO 105-F02 and dyed with C.I. Direct Blue 71 NOTE Cotton dyed reference fabric is only availabl
25、e from lInstitut francais du textile et de lhabillement, Direction rgionale Est, 25, rue Alfred Werner, 68059 Mulhouse Cedex 2, France 4 Specification for cotton rubbing cloth The fabric shall have the following properties. 4.1 Mass per unit area: (110 5) g/m2, determined in accordance with ISO 3801
26、. 4.2 Whiteness value: Y10= 89 2 W10= 78 3 T10= 1 1 Measurements shall be made with the specular component included in accordance with ISO 105-J01, excluding 0/45 (45/0). Luminance (Y10), whiteness (W10) and tint (T10) values shall be calculated using CIE standard illuminant D65 and CIE 1964 supplem
27、entary standard colorimetric observer (10 observer) in accordance with ISO 105-J02. Measure the whiteness degree of at least a four-layer cotton rubbing cloth to obtain a uniform whiteness measurement. 4.3 Residual oil content: less than 1 %. 4.4 The pH of the aqueous extract: the pH shall be 7,5 1,
28、0 when determined by the method specified in ISO 3071. NOTE Information about the production of the cotton rubbing cloth is included in a report by the co-secretariats of ISO/TC 38/SC 1. SANS 105-F09:2009This s tandard may only be used and printed by approved subscription and freemailing clients of
29、the SABS .ISO 105-F09:2009(E) ISO 2009 All rights reserved 35 Assessment of staining properties of cotton rubbing cloth under test 5.1 General As cotton rubbing cloths are required to yield reproducible results when used in colour fastness to rubbing tests, their most important property is standardi
30、zed staining characteristics. The staining characteristics of the cotton rubbing cloth under test shall conform to those of the cotton rubbing cloth reference fabric when performing colour fastness to rubbing tests on the cotton dyed reference fabric. 5.2 Test procedure Conduct tests in accordance w
31、ith ISO 105-X12, using the cotton dyed reference fabric, with ten pieces of cotton rubbing cloth under test and with ten pieces of cotton rubbing cloth reference fabric. NOTE Information about the production of the cotton dyed reference fabric is included in a report by the co-secretariats of ISO/TC
32、 38/SC 1. 5.3 Performance requirements The colour difference between the mean of the ten pieces of cotton rubbing cloth under test and the mean of the ten pieces of cotton rubbing cloth reference fabric shall not be greater than 4-5 when evaluated using the grey scale for assessing change in colour,
33、 in accordance with ISO 105-A02 or ISO 105-A05. SANS 105-F09:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 105-F09:2009(E) 4 ISO 2009 All rights reservedBibliography 1 ISO 105-A01, Textiles Tests for colour fastness Part A01: Genera
34、l principles of testing 2 CIE Publication No. 15:2004, Colorimetry, 3rd ed. SANS 105-F09:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .SABS Standards Division The objective of the SABS Standards Division is to develop, promote and maint
35、ain South African National Standards. This objective is incorporated in the Standards Act, 2008 (Act No. 8 of 2008). Amendments and Revisions South African National Standards are updated by amendment or revision. Users of South African National Standards should ensure that they possess the latest am
36、endments or editions. The SABS continuously strives to improve the quality of its products and services and would therefore be grateful if anyone finding an inaccuracy or ambiguity while using this standard would inform the secretary of the technical committee responsible, the identity of which can
37、be found in the foreword. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 The SABS offers an individual notification service, which ensures that subscribers automatically receive notification regarding amendments and revisions to South African National Standards. Tel: +27 (0) 12 428 6883 Fax: +27
38、(0) 12 428 6928 E-mail: salessabs.co.za Buying Standards Contact the Sales Office for South African and international standards, which are available in both electronic and hardcopy format. Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: salessabs.co.za South African National Standards are
39、also available online from the SABS website http:/www.sabs.co.za Information on Standards The Standards Information Centre provides a wide range of standards-related information on both national and international standards, and is the official WTO/TBT enquiry point for South Africa. The Centre also
40、offers an individual updating service called INFOPLUS, which ensures that subscribers automatically receive notification regarding amendments to, and revisions of, international standards. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: infosabs.co.za Copyright The copyright in a South Afr
41、ican National Standard or any other publication published by the SABS Standards Division vests in the SABS. Unless exemption has been granted, no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means without prior written permission from the SABS Standard
42、s Division. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any purpose other than implementation, prior written permission must be obtained. Details and advice can be obtained from the Senior Manager. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: infosabs.co.za
