1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA
2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any
3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-19958-6 SANS 11662-1:2007 Edition 1 ISO 11662-1:1995 Edition 1 SOUTH AFRICAN NATIONAL STANDARD Mobile cranes Experimental determination of
4、 crane performance Part 1: Tipping loads and radii This national standard is the identical implementation of ISO 11662-1:1995 and is adopted with the permission of the International Organization for Standardization. Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pr
5、etoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code +27 12 www.stansa.co.za Standards South Africa This standard may only be used and printed by approved subscription and freemailing clients of the SABS.SANS 11662-1:2007 Edition 1 ISO 11662-1:1995 Edition 1 Table of changes Change No.
6、 Date Scope National foreword This South African standard was approved by National Committee StanSA SC 5120.59B, Cranes Mobile cranes, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in May 2007. This stan
7、dard may only be used and printed by approved subscription and freemailing clients of the SABS.INTERNATIONAL STANDARD 116624 First edition 1995-06-01 Mobile cranes - Experimental determination of crane Performance - Part 1: Tipping loads and radii Grues mobiles - D b) fuel supply; d tyre inflation;
8、d) coolant supply; 6 Test conditions e) track tension; 6.1 For the purpose of testing, the crane shall be equipped with working equipment suitable for Operation with the rated load. bolts, Pins, cable components; fittings and other load-bearing g) clutches, brakes and other power transmission compon
9、ents; 6.2 When testing cranes on pneumatic tyres or crawler equipment, the appliance shall be placed on a firm level surface (6 1 % gradient). h) boom length and rigging; j) crane level (G 1 % gradient). 7.1.2 A competent Operator shall operate the crane. In the absence of specific recommendations,
10、a new machine should be operated for at least 4 h to ensure proper function of the machine. At the conclusion of this initial Operation, Service and adjust the machine to the specified conditions. 6.3 When testing pneumatic-tyred equipment while operating on tyres, the tyres shall be inflated to wit
11、hin +3 % of the pressure stipulated by the manufacturer, and all wheels shall be in the ahead Position. Conditions for tyre support shall comply with manufacturers requirements. 7.1.3 Locate the crane on the test course in Position for loading and actuate the travel brakes. 6.4 For conducting tests
12、of cranes with outriggers in the “on outriggers” condition, the crane shall be level (G 1% gradient). 7.1.4 Set outriggers, if used, and jack the crane to a Position in which the tyres or tracks within the boundary of the outriggers are unloaded. 6.4.1 When outriggers are used in the course of testi
13、ng pneumatic-tyred cranes, the crane shall be raised by the outriggers so as to provide clearance between the ground and all the wheels or to relieve all wheels of the weight of the crane unless the Suspension design is such that the tyres stay on the ground when outriggers are set. 7.1.5 Vertically
14、 project the superstructure axis-of- rotation onto the surface of the test course and mark its location. 7.2 Test measurements 7.2.1 Prepare test load, including test weights, hook block, Slings and any other ancillary equipment, such as Poad basket, to make up the specified load mass to within + 1
15、%. Record this value. 6.4.2 When outriggers are used in the course of testing crawler cranes, the crane shall be installed so as to ensure firm bearing of the outriggers on the supporting surface. 2 SANS 11662-1:2007This standard may only be used and printed by approved subscription and freemailing
16、clients of the SABS.0 ISO ISO 116621:1995(E) 7.2.2 With the crane superstructure in its least stable configuration for the specified Position, hoist the load free from the test surface at a radius at which the crane is stable; then boom down a small amount to increase the radius. Keep the load withi
17、n 0,l m of the test surface at all times to prevent excessive tipping. If the crane will support the load at the adjusted radius without tipping, measure and record the new radius. Repeat the procedure until the balance Point is reached. When the balance Point is reached, record the mass of the load
18、 and radius of the load. NOTE 1 The final adjustment of the balance Point may be made by adding small increments of mass rather than increasing the radius. 7.2.3 Alternatively, measure the radius of load and add small increments of mass to the load until the load overcomes the stability of the crane
19、. The radius of load and load mass last employed, before the stability of the crane was overcome, shall be recorded as the balance Point condition. 8 Plotting of capacity curve Where it is desired to determine the balance Point capacities of a crane throughout a range of loads or radii, follow proce
20、dures as outlined in 7.2, making Sure that the load and radius are determined for each extreme of the Chosen range and at a sufficient number of intermediate Points to permit plotting a curve. Plot a curve showing the maximum capacity of the crane with the load, in kilograms, as Ordinate and radius,
21、 in metres, as abscissa. Use a representative number of boom lengths for a given capacity Chart. 9 Test report Record a complete description of the crane, positions for the test, data for the tipping load and the radius of load on test data sheets. See table 1 and figures 1 and 2 for examples of tes
22、t data sheets. SANS 11662-1:2007This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 116621:1995(E) Table 1 - Data sheet for mobile crane description and balance Points 0 ISO Manufacturer . Model . Condition: New 0 Used 0 Mounting: Type . Tyres:
23、 Size . Radial Ply Boom: Type . Boom jib: Type Length (m) Engine: Manufacturer Model . Counterweight: Type . Test method: Suspended weights 0 Serial No . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hours of previous use . . . . . . . . . . . . .
24、. . . . . . . . . . . . . . . . Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pressure (kPa) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . r Length (m) n“. Angle to the boom/groundl) . . . . . .
25、. . . . . . . . . . . . . . Serial No . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mass (kg) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Anchor 0 Position of superstructure I I I I Remarks: .
26、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operator: . Date of test: 1) When fly jib is fixed, the angle is to the boom; when fly jib is luffing, the angle is to the ground. 4 SANS 11662-1:2007This standard may only be used and printed by approved subscription and freemailing
28、 clients of the SABS.0 ISO ISO 116621:1995(E) I - 0 -Y-P- -e- y+!)!-+qlll T ( -i ,!+q I! : -j- - f (+ .J -+i- -+ ) b 77 :r-.i I 4 P-P- - - 39=- f#+ -Ti $q” A 8 x Gtruck I - I 6 x Gtruck Dimensionsofundercarriagechassis for wheel-mountedcranes A B C 0 E F G H J I Figure 1 - Data sheet for physical dimensions of undercarriage Chassis for wheel-mounted cranes 5 SANS 11662-1:2007This standard may only be used and printed by approved subscription and freemailing clients of the SABS.
