1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA
2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any
3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-22548-3 SANS 7811-9:2009 Edition 1 ISO/IEC 7811-9:2008 Edition 1SOUTH AFRICAN NATIONAL STANDARD Identification cards Recording technique P
4、art 9: Tactile identifier mark This national standard is the identical implementation of ISO/IEC 7811-9:2008 and is adopted with the permission of the International Organization for Standardization and the International Electrotechnical Commission. Published by SABS Standards Division 1 Dr Lategan R
5、oad Groenkloof Private Bag X191 Pretoria 0001 Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS This standard may only be used and printed by approved subscription and freemailing clients of the SABS.SANS 7811-9:2009 Edition 1 ISO/IEC 7811-9:2008 Edition 1 Table of changes Change No. Dat
6、e Scope National foreword This South African standard was approved by National Committee SABS SC 71J, Information technology Cards and personal identification, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was pu
7、blished in April 2009. This standard may only be used and printed by approved subscription and freemailing clients of the SABS. Reference number ISO/IEC 7811-9:2008(E) ISO/IEC 2008INTERNATIONAL STANDARD ISO/IEC 7811-9 First edition 2008-06-01 Identification cards Recording technique Part 9: Tactile
8、identifier mark Cartes didentification Technique denregistrement Partie 9: Marque didentificateur tactile SANS 7811-9:2009This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO/IEC 7811-9:2008(E) PDF disclaimer This PDF file may contain embedded t
9、ypefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not in
10、fringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were o
11、ptimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2008 All rights rese
12、rved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the reques
13、ter. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO/IEC 2008 All rights reservedSANS 7811-9:2009This standard may only be used and printed by approved subscription and freemai
14、ling clients of the SABS.ISO/IEC 7811-9:2008(E) ISO/IEC 2008 All rights reserved iii Contents Page Foreword iv 1 Scope. 1 2 Conformance. 1 3 Normative references. 1 4 Terms, definitions and abbreviations. 1 4.1 Terms and definitions. 1 4.2 Abbreviations 1 5 TIM physical characteristics 2 5.1 Locatio
15、n of TIM . 2 5.2 TIM dot arrangement 2 5.3 Dot dimensions . 3 5.4 Sign design 3 SANS 7811-9:2009This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO/IEC 7811-9:2008(E) iv ISO/IEC 2008 All rights reservedForeword ISO (the International Organizati
16、on for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respecti
17、ve organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
18、technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical committee is to prepare International Standards. Draft International Sta
19、ndards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the
20、 subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. ISO/IEC 7811-9 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 17, Cards and personal identification. ISO/IEC 7811 consists of the foll
21、owing parts, under the general title Identification cards Recording technique: Part 1: Embossing Part 2: Magnetic stripe Low coercivity Part 6: Magnetic stripe High coercivity Part 7: Magnetic stripe High coercivity, high density Part 8: Magnetic stripe Coercivity of 51,7 kA/m (650 Oe) Part 9: Tacti
22、le identifier mark SANS 7811-9:2009This standard may only be used and printed by approved subscription and freemailing clients of the SABS.INTERNATIONAL STANDARD ISO/IEC 7811-9:2008(E) ISO/IEC 2008 All rights reserved 1 Identification cards Recording technique Part 9: Tactile identifier mark 1 Scope
23、 This part of ISO/IEC 7811 specifies the physical characteristics of a tactile identifier mark used by visually- impaired card holders to distinguish their cards. It defines the area on the card for the tactile identifier mark (TIM) and the layout of Braille-style embossed dots arranged in patterns
24、to enable easy tactile recognition. 2 Conformance A TIM is in conformance with this part of ISO/IEC 7811 if it meets all mandatory requirements, and optional requirements as specified. 3 Normative references The following referenced documents are indispensable for the application of this document. F
25、or dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/IEC 7810, Identification cards Physical characteristics ISO/IEC 7811-1, Identification cards Recording technique Part 1: Embossing 4 Term
26、s, definitions and abbreviations 4.1 Terms and definitions For the purposes of this document, the terms and definitions given in ISO/IEC 7810 and the following apply. 4.1.1 embossed raised in relief from the front surface of the card by adding or reacting card material, or by deforming the card mate
27、rial from the opposite side 4.2 Abbreviations TIM tactile identifier mark SANS 7811-9:2009This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO/IEC 7811-9:2008(E) 2 ISO/IEC 2008 All rights reserved5 TIM physical characteristics 5.1 Location of TI
28、M The TIM should be located on the front surface of the card in the area shown in Figure 1. The TIM shall not be located outside the Name and address area defined by ISO/IEC 7811-1. Regardless of TIM location, all other raised areas shall be at least 1 mm from the edge of any TIM. NOTE Certain embos
29、sing techniques can damage card components that exist in TIM area. b d a c TIM area dimensions in millimetres (inches) Top reference edge Front of card a 18,5 (0.728) maximum b 8 (0.315) maximum c 10 1 (0.394 0.039) d 2,92 0,38 (0.115 0.015) Figure 1 Recommended TIM area 5.2 TIM dot arrangement The
30、TIM shall be composed of a maximum of 3 groups of 6 dots arranged as shown in Figure 2. SANS 7811-9:2009This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO/IEC 7811-9:2008(E) ISO/IEC 2008 All rights reserved 3 dimensions in millimetres (inches)
31、a b c d e a 2,3 (0.091) b 4,6 (0.181) c 2,3 (0.091) 3 places d 6,1 (0.240) e 12,2 (0.480) Figure 2 Arrangement of TIM dots 5.3 Dot dimensions Dots used to make up the TIM shall have a relief height of 0,48 mm (0.019 inch) maximum and 0,3 mm (0.012 inch) minimum above the adjacent surface of the card
32、. The shape of each dot is not specified; examples are shown in Figure 3. 1,45 0,2 (0.057 0.008) diameter dimensions in mm (inch) 1,45 0,2 (0.057 0.008) diameter Figure 3 TIM dot base size and shape illustration a 5.4 Sign design It is recommended that the card holder select which of the 18 possible
33、 dots are to be raised. The maximum number of raised dots is 18 and the minimum is 1. NOTE Since there are individual differences in discernment by the tactile sense, it is recommended that the card holder be able to use the combination of the dots that is easy for them to discriminate. SANS 7811-9:
34、2009This standard may only be used and printed by approved subscription and freemailing clients of the SABS. This page has been left blank intentionally This standard may only be used and printed by approved subscription and freemailing clients of the SABS. SABS Standards Division The objective of t
35、he SABS Standards Division is to develop, promote and maintain South African National Standards. This objective is incorporated in the Standards Act, 2008 (Act No. 8 of 2008). Amendments and Revisions South African National Standards are updated by amendment or revision. Users of South African Natio
36、nal Standards should ensure that they possess the latest amendments or editions. The SABS continuously strives to improve the quality of its products and services and would therefore be grateful if anyone finding an inaccuracy or ambiguity while using this standard would inform the secretary of the
37、technical committee responsible, the identity of which can be found in the foreword. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 The SABS offers an individual notification service, which ensures that subscribers automatically receive notification regarding amendments and revisions to South Afr
38、ican National Standards. Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: salessabs.co.za Buying Standards Contact the Sales Office for South African and international standards, which are available in both electronic and hardcopy format. Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-
39、mail: salessabs.co.za South African National Standards are also available online from the SABS website http:/www.sabs.co.za Information on Standards The Standards Information Centre provides a wide range of standards-related information on both national and international standards, and is the offici
40、al WTO/TBT enquiry point for South Africa. The Centre also offers an individual updating service called INFOPLUS, which ensures that subscribers automatically receive notification regarding amendments to, and revisions of, international standards. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-
41、mail: infosabs.co.za Copyright The copyright in a South African National Standard or any other publication published by the SABS Standards Division vests in the SABS. Unless exemption has been granted, no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any me
42、ans without prior written permission from the SABS Standards Division. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any purpose other than implementation, prior written permission must be obtained. Details and advice can be obtained from the Senior Manager. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: infosabs.co.za This standard may only be used and printed by approved subscription and freemailing clients of the SABS.
