SFS 2445-1969 《钢螺纹管连接 连接盒的弓形管 90和45》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSS-M2D451-B2-2008 HYDROGENATED NITRILE (HNBR) RUBBER 70 DUROMETER TO BE USED WITH FORD WSS-M99P1111-A (Shown on WSS-M2D451-B1)《硬度70的氢化丁腈橡胶(HNBR) 与标准FORD WSS-M99P1111-A一起使用.pdf

FORD WSS-M2D451-B3-2016 HYDROGENATED NITRILE (HNBR) RUBBER HIGH TEMPERATURE COOLANT SEAL 70 DUROMETER A HARDNESS TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSS-M2D452-A4-2010 THERMOPLASTIC POLYESTER-ETHER ELASTOMER (TEEE) MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《热塑性聚酯乙醚弹性体（TEEE）成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD WSS-M2D463-A2-2009 HYDROGENATED NITRILE BUTADIENE RUBBER (HNBR) SUPERIOR COMPRESSION SET REFRIGERANT AND OIL RESISTANT O-RINGS TO BE USED WITH FORD WSS-M99P1111-A (Shown on .pdf

FORD WSS-M2D470-A5-2004 DUCT EPDM LOW OIL SWELL MOLDED AIR INTAKE TO BE USED WITH FORD WSS-M99P1111-A (Shown on WSE-M2D470-A1)《模制进气口用低油膨胀性三元乙丙橡胶(EPDM)管 与标准FORD WSS-M99P1111-A一起使.pdf

FORD WSS-M2D470-A5-2013 DUCT EPDM LOW OIL SWELL MOLDED AIR INTAKE TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSE-M2D470-A1).pdf

FORD WSS-M2D474-A2-2004 THERMOPLASTIC ELASTOMER (TES) STYRENE BLOCK COPOLYMER 60 DUROMETER A HARDNESS EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部用硬度为60 A的热塑性弹性体(TES)苯乙烯嵌段共.pdf

FORD WSS-M2D474-A2-2016 THERMOPLASTIC ELASTOMER (TES) STYRENE BLOCK COPOLYMER 60 DUROMETER A HARDNESS EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSS-M2D475-A2-2009 HYDROGENATED ACRYLONITRILE BUTADIENE (HNBR) O-RING TO BE USED WITH FORD WSS-M99P1111-A 《氢化丙烯腈丁二烯（HNBR）O形环 与标准FORD WSS-M99P1111-A一起使用 》.pdf