SIS SS 3370-1980 Milling cutters Parallel shanks with flat《铣刀 平直柄》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

NEN-ISO 8662-1-1993 Hand-held portable power tools Measurement of vibrations at the handle Part 1 General (ISO 8662-1 1988)《SO 8662-1-1988 便携式手提动力工具 手柄振动测量 第1部分：总则》.pdf

NEN-ISO 8692-1993 Water quality Fresh water algal growth inhibition test with Scenedesmus subspicatus and Selenastrum capricornutum (ISO 8962 1989)《ISO 8692-1989 水质 用绿藻类栅薄属和月牙藻属进行的.pdf

NEN-ISO 8733-1992 Parallel pins with internal thread unhardened (ISO 8733 1986)《ISO 8733-1986 未淬硬钢带内螺纹平行销》.pdf

NEN-ISO 8734-1992 Parallel pins hardened (Dowel pins) (ISO 8734 1987)《ISO 8734- 1987 淬硬钢平行销（定位销）》.pdf

NEN-ISO 8739-1992 Grooved pins Full-length parallel grooved with pilot (ISO 8739 1986)《ISO 8739-1986 槽销 带导杆及全长平行沟槽》.pdf

NEN-ISO 8740-1992 Grooved pins Full-length parallel grooved with chamfer (ISO 8740 1986)《ISO 8740-1986 槽销 带倒角及全长平行沟槽》.pdf

NEN-ISO 8741-1992 Grooved pins Half-length reverse taper grooved (ISO 8741 1986)《ISO 8741-1986 槽销 半长倒锥槽》.pdf

NEN-ISO 8742-1992 Grooved pins Third-length centre grooved (ISO 8742 1986)《ISO 8742-1986 槽销 中部槽长为1 3全长》.pdf

NEN-ISO 8744-1992 Grooved pins Full-length taper grooved (ISO 8744 1986)《ISO 8744-1986 槽销 全長锥槽》.pdf