SIS SS-IEC 676-1992 Test methodsfor direct arcfurnaces《直流电弧炉检测方法》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

NF E25-021-1994 Cross recesses for screws 《螺钉的十字槽(欧洲标准EN ISO 4757)》.pdf

NF E25-022-1987 Fasteners Tolerances for bolts screws and nuts product grade F (fine mechanic) Thread diameters from 1 up to 3 mm 《紧固件 F级螺钉和螺帽公差（精密机械） 螺纹直径1到3mm》.pdf

NF E25-023-1992 Fasteners Clearance hole for bolts and screws 《紧固件 螺栓和螺钉的间隙孔》.pdf

NF E25-080-2005 Single pegs used in department stores - Safety requirements and test method 《百货商店用单销 安全要求和试验方法》.pdf

NF E25-100-3-1992 Fasteners Surface discontinuities Part 1 bolts screws and studs for general requirements 《紧固件 表面不连续性 第1部分 一般要求的螺栓、螺钉和螺柱》.pdf

NF E25-100-4-1992 Fasteners Surface discontinuties Part 3 bolts screw and studs for special requirements 《紧固件 表面不连续性 第3部分 特殊要求的螺栓、螺钉和螺柱》.pdf

NF E25-100-7-1995 Mechanical properties of fasteners Part 7 torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm 《紧固件机械性能 第7部分 公称直径1-10mm的螺.pdf

NF E25-101-1996 Technical product documentation Springs Part 2 presentation of data for cylindrical helical compression springs 《技术产品文献 弹簧 第2部分 圆柱螺旋状压缩弹簧的数据表示》.pdf

NF E25-113-1992 Fasteners Hexagon head bolts Product grade B Reduced shank (shank diameter = pitch diameter) 《紧固件 六角头螺栓 B级产品、减小螺杆的螺栓（杆径 ＝ 中径）》.pdf