UNE 64 022-1966 《化合饲料及其初期材料中矿物材料分析的样本准备：锌；铁；铜；钼和钴》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

SIS SS 2426-1979 ISO system for inspection of plain workpieces Tolerances for gauges for holes ZA7 to ZA9《ISO光滑工件检验体系 孔量规公差ZA7 to ZA9》.pdf

SIS SS 2427-1979 ISO system for inspection of plain workplaces Tolerances for gauges for holes ZB8 to ZB10《仪器 ISO光滑工件检验体系 孔量规公差ZB8至ZB10》.pdf

SIS SS 2428-1979 ISO system for inspection of plain workpieces Tolerances for gauges for holes ZC8 to ZC10《ISO光滑工件检验体系 孔量规公差ZC8 - ZC10》.pdf

SIS SS 2430-1988 Hoists for disabled persons Mobile hoists Safety requirements and testing《残疾人升降器 移动升降器 安全要求和试验》.pdf

SIS SS 2431-1979 fSO system for inspection of plain workpieces Tolerances for gauges for shafts a 10 to a13《ISO光滑工件检验体系 轴量规公差A10至A13》.pdf

SIS SS 2432-1979 ISO system for inspection of plain workpieces - Tolerances for gauges for shafts b9 to b13《ISO光滑工件检验体系 孔量规公差b9 - b13》.pdf

SIS SS 2433-1979 ISO system for inspection of plain workpieces Tolerances for gauges for shafts c8 to c12《ISO光滑工件检验体系 轴量规公差c8至c12》.pdf

SIS SS 2434-1979 ISO system for inspection of plain workpieces Tolerances for gauges for shafts cd7 to cd10《仪器 ISO光滑工件检验体系 轴量规公差cd7至cd10》.pdf

SIS SS 2435-1979 ISO system for inspection of plain workpieces Tolerances for gauges for shafts d7 to d11《仪器 ISO光滑工件检验体系 轴量规公差d7至d11》.pdf