1、12-10 08 80 00-1 SECTION 08 80 00 GLAZING SPEC WRITER NOTES: 1. Delete between / - / if not applicable to project. 2. Also delete any other item or paragraph not applicable in section and renumber paragraph. 3. Coordinate with other sections to specify type of glazing required. 4. See Consumer Produ
2、ct Safety Commission requirements for “Safety Glass.“ Category II (CPSC 16CFR-1201). 5. See VA Architectural Design Guides for VA criteria on windows. 6. Determine design loads on glazing required by building code. Specify glazing to meet design loads. 7. See VA Physical Security Design Guide for gl
3、azing requirements of blast-resistant windows. PART 1 - GENERAL 1.1 DESCRIPTION This section specifies glass, plastic, related glazing materials and accessories. Glazing products specified apply to factory or field glazed items. 1.2 RELATED WORK A. Factory glazed by manufacturer in following units:
4、1. Sound resistant doors: Section 08 11 13, HOLLOW METAL DOORS AND FRAMES, and Section 08 14 00, WOOD DOORS. 2. Revolving doors: Section 08 42 33, REVOLVING DOOR ENTRNCES. 3. Forced Entry (FE) resistant and Ballistic Resistance (BR) rated glazing and frames: 08 56 53 SECURITY WINDOWS 4. Mirrors: Sec
5、tion 10 28 00, TOILET, BATH, AND LAUNDRY ACCESSORIES. 5. Bullet resisting glass: Section 08 56 59, SERVICE AND TELLER WINDOW UNITS. 6. Lead glass: Section 13 49 00, RADIATION PROTECTION. 7. Section 08 51 13, ALUMINUM WINDOWS (Single / Double / Triple / Hung). 8. Section 08 51 13.11, SIDE HINGED ALUM
6、INUM WINDOWS (Double Glazed). 9. Section 08 44 13, GLAZED ALUMINUM CURTAIN WALLS. 10. Section 08 56 53 SECURITY WINDOWS. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-12-10 08 80 00-2 11. Color of spandrel glass, tinted (heat absorbing or light red
7、ucing) glass, and reflective (metallic coated) glass: Section 09 06 00, SCHEDULE FOR FINISHES. 12. Forced Entry (FE) resistant and Ballistic Resistance (BR) rated doors and frames: Section 08 34 53, SECURITY DOORS AND FRAMES. 13. Section 28 13 11, PHYSICAL ACCESS CONTROL SYSTEMS. 14. Section 28 16 1
8、1, INTRUSION DETECTION SYSTEM. 1.3 LABELS A. Temporary labels: 1. Provide temporary label on each light of glass / and plastic material / identifying manufacturer or brand and glass type, quality and nominal thickness. 2. Label in accordance with NFRC (National Fenestration Rating Council) label req
9、uirements. 3. Temporary labels shall remain intact until glass / and plastic material / is approved by Resident Engineer. B. Permanent labels: 1. Locate in corner for each pane. 2. Label in accordance with ANSI Z97.1 and SGCC (Safety Glass Certification Council) label requirements. a. Tempered glass
10、. b. Laminated glass or have certificate for panes without permanent label. c. Organic coated glass. 3. Bullet resistance glass or plastic assemblies: a. Bullet resistance glass or plastic assemblies in accordance with UL 752 requirements for power rating specified. b. Identify each security glazing
11、 permanently with glazing manufacturers name, date of manufacture, product number, and DOS Code number inconspicuously located in lower corner on protective side and visible after glazing is framed. c. The “attack (threat) side“ shall be identified in bold lettering on each side of glazing with remo
12、vable label. 1.4 PERFORMANCE REQUIREMENTS A. Building Enclosure Vapor Retarder and Air Barrier: 1. Utilize the inner pane of multiple pane sealed units for the continuity of the air barrier and vapor retarder seal. Provided by IHSNot for ResaleNo reproduction or networking permitted without license
13、from IHS-,-,-12-10 08 80 00-3 2. Maintain a continuous air barrier and vapor retarder throughout the glazed assembly from glass pane to heel bead of glazing sealant. SPEC WRITER NOTE: Verify that local authorities have adopted (and that their own requirements do not exceed) ASCE 7 (American Society
14、of Civil Engineers). List local requirements where more stringent. B. Glass Thickness: 1. Select thickness of exterior glass to withstand dead loads and wind loads acting normal to plane of glass at design pressures calculated in accordance with / ASCE 7 / applicable / code. 2. Test in accordance wi
15、th ASTM E 1300. 3. Thicknesses listed are minimum. Coordinate thicknesses with framing system manufacturers. C. Bullet resistance glass or plastic assemblies: 1. For blast resistant windows follow Unified Facilities Criteria, DOD Minimum Antiterrorism Standards for Buildings UFC4-010-01. 2. Spall Re
16、sistance: Laminated glazing shall not produce spall to interior (protected side) when impacted with scheduled ballistics. Tolerances: 3. Outside dimensions: Overall outside dimensions (height and width) of laminated security glazing shall maintain tolerance of 3 mm. 4. Warpage: Out-of-flat (warpage
17、or bowing) condition of laminates shall not exceed 2.5 mm per lineal meter. The condition, if present, shall be localized to extent not greater than 0.75 mm for any 0.3 meter section. 5. Coordinate with Physical Security Design Manual requirements. 1.5 SUBMITTALS SPEC WRITER NOTE: List below items i
18、ntended for use in project, necessary for review prior to manufacture. Refer to Section 01 33 23, SHOP DRAWINGS, PRODUCT DATA, AND SAMPLES for submittal requirements. Include additional submittal requirements for items specified. A. In accordance with Section 01 33 23, SHOP DRAWINGS, PRODUCT DATA, A
19、ND SAMPLES. B. Manufacturers Certificates: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-12-10 08 80 00-4 1. Certificates stating that wire glass, meets requirements for safety glazing material as specified in ANSI Z97.1. 2. Certificate on shading
20、coefficient. 3. Certificate on “R“ value when value is specified. 4. Certificate test reports confirming compliances with specified bullet resistive rating. 5. Certificate that blast resistant glass meets the requirements of UFC4-010-01. C. Warranty: Submit written guaranty, conforming to General Co
21、ndition requirements, and to “Warranty of Construction” Article in this Section. D. Manufacturers Literature and Data: 1. Glass, each kind required. 2. Insulating glass units. 3. Transparent (one-way vision glass) mirrors. 4. Elastic compound for metal sash glazing. 5. Putty, for wood sash glazing.
22、6. Glazing cushion. 7. Sealing compound. 8. Bullet resistive material. 9. Plastic glazing material, each type required. E. Samples: 1. Size: 150 mm by 150 mm (6 inches by 6 inches). 2. Tinted glass. 3. Reflective glass. 4. Transparent (one-way vision glass) mirrors. F. Preconstruction Adhesion and C
23、ompatibility Test Report: Submit glazing sealant manufacturers test report indicating glazing sealants were tested for adhesion to glass and glazing channel substrates and for compatibility with glass and other glazing materials. 1.6 DELIVERY, STORAGE AND HANDLING A. Delivery: Schedule delivery to c
24、oincide with glazing schedules so minimum handling of crates is required. Do not open crates except as required for inspection for shipping damage. B. Storage: Store cases according to printed instructions on case, in areas least subject to traffic or falling objects. Keep storage area clean and dry
25、. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-12-10 08 80 00-5 C. Handling: Unpack cases following printed instructions on case. Stack individual windows on edge leaned slightly against upright supports with separators between each. D. Protect la
26、minated security glazing units against face and edge damage during entire sequence of fabrication, handling, and delivery to installation location. Provide protective covering on exposed faces of glazing plastics, and mark inside as “INTERIOR FACE“ or “PROTECTED FACE“: 1. Treat security glazing as f
27、ragile merchandise, and packaged and shipped in export wood cases with width end in upright position and blocked together in a mass. Storage and handling shall comply with Manufacturers directions and as required to prevent edge damage or other damage to glazing resulting from effects of moisture, c
28、ondensation, temperature changes, direct exposure to sun, other environmental conditions, and contact with chemical solvents. 2. Protect sealed-air-space insulating glazing units from exposure to abnormal pressure changes, as could result from substantial changes in altitude during delivery by air f
29、reight. Provide temporary breather tubes which do not nullify applicable warranties on hermetic seals. 3. Temporary protections: The glass front and polycarbonate back of glazing shall be temporarily protected with compatible, peelable, heat-resistant film which will be peeled for inspections and re
30、-applied and finally removed after doors and windows are installed at destination. Since many adhesives will attack polycarbonate, the film used on exposed polycarbonate surfaces shall be approved and applied by manufacturer. 4. Edge protection: To cushion and protect glass clad, polycarbonate, and
31、Noviflex edges from contamination or foreign matter, the four edges shall be sealed the depth of glazing with continuous standard-thickness Santoprene tape. Alternatively, continuous channel shaped extrusion of Santoprene shall be used, with flanges extending into face sides of glazing. 5. Protect “
32、Constant Temperature“ units including every unit where glass sheet is directly laminated to or directly sealed with metal-tube type spacer bar to polycarbonate sheet, from exposures to ambient temperatures outside the range of 16 to 24 C, during the Provided by IHSNot for ResaleNo reproduction or ne
33、tworking permitted without license from IHS-,-,-12-10 08 80 00-6 fabricating, handling, shipping, storing, installation, and subsequent protection of glazing. 1.7 PROJECT CONDITIONS Field Measurements: Field measure openings before ordering tempered glass products. Be responsible for proper fit of f
34、ield measured products. 1.8 WARRANTY A. Warranty: Conform to terms of “Warranty of Construction“, FAR clause 52.246-21, except extend warranty period for the following: 1. Bullet resistive plastic material to remain visibly clear without discoloration for 10 years. 2. Insulating glass units to remai
35、n sealed for 10 years. 3. Laminated glass units to remain laminated for 5 years. 4. Polycarbonate to remain clear and ultraviolet light stabilized for 5 years. 5. Insulating plastic to not have more than 6 percent decrease in light transmission and be ultraviolet light stabilized for 10 years. 1.9 A
36、PPLICABLE PUBLICATIONS A. Publications listed below form a part of this specification to extent referenced. Publications are referenced in text by basic designation only. B. American National Standards Institute (ANSI): Z97.1-04Safety Glazing Material Used in Building - Safety Performance Specificat
37、ions and Methods of Test. C. American Society for Testing and Materials (ASTM): C1363-05Thermal Performance of Building Assemblies, by Means of A Hot Box Apparatus C542-05.Lock-Strip Gaskets. C716-06.Installing Lock-Strip Gaskets and Infill Glazing Materials. C794-06.Adhesion-in-Peel of Elastomeric
38、Joint Sealants. C864-05.Dense Elastomeric Compression Seal Gaskets, Setting Blocks, and Spacers. C920-08.Elastomeric Joint Sealants. C964-07.Standard Guide for Lock-Strip Gasket Glazing. C1036-06Flat Glass. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS
39、-,-,-12-10 08 80 00-7 C1048-04Heat-Treated Flat Glass-Kind HS, Kind FT Coated and Uncoated Glass. C1172-09Laminated Architectural Flat Glass. C1376-10Pyrolytic and Vacuum Deposition Coatings on Flat Glass. D635-06.Rate of Burning and/or Extent and Time of Burning of Self-Supporting Plastic in a Hori
40、zontal Position. D4802-02Poly (Methyl Methacrylate) Acrylic Plastic Sheet. E84-09Surface Burning Characteristics of Building Materials. E1300-09Determining Load Resistance of Glass in Buildings. E2190-08Insulating Glass Unit D. Commercial Item Description (CID): A-A-59502.Plastic Sheet, Polycarbonat
41、e E. Code of Federal Regulations (CFR): 16 CFR 1201 - Safety Standard for Architectural Glazing Materials; 1977, with 1984 Revision. F. National Fire Protection Association (NFPA): 80-08.Fire Doors and Windows. G. National Fenestration Rating Council (NFRC) H. Safety Glazing Certification Council (S
42、GCC)2009: Certified Products Directory (Issued Semi-Annually). I. Underwriters Laboratories, Inc. (UL): 752-06Bullet-Resisting Equipment. J. Unified Facilities Criteria (UFC): 4-010-01-2007.DOD Minimum Antiterrorism Standards for Buildings K. Glass Association of North America (GANA): Glazing Manual
43、 (Latest Edition) Sealant Manual (2008) L. American Society of Civil Engineers (ASCE): ASCE 7-10.Wind Load Provisions PART 2 - PRODUCT SPEC WRITER NOTES: 1. Refer to glass manufacturers literature for structural properties. Provided by IHSNot for ResaleNo reproduction or networking permitted without
44、 license from IHS-,-,-12-10 08 80 00-8 2. Specify glass by thickness and ASTM designations and supplement standard for additional properties. Refer to information following end of section for guides to ASTM C 1036 and C 1048 designations. 3. Establish and coordinate glass types to identify glass or
45、glazing assemblies on drawings, preferably on exterior elevations for exterior windows. 4. Coordinate to retain glass types required with glazing assemblies. 2.1 GLASS A. Use thickness stated unless specified otherwise in assemblies. SPEC WRITER NOTE: Usually specify quality q3; use q4 for general g
46、lazing applications. B. Clear Glass: 1. ASTM C1036, Type I, Class 1, Quality / q3 / / q4 /. 2. Thickness, / 6 mm (1/4 inch) / /as indicated /. SPEC WRITER NOTES: 1. Select tint color from manufacturers data and samples. 2. Note that varying thicknesses of tinted or heat absorbing glass exhibit diffe
47、rent color shades of the same tint. 3. Coordinate color/tint/coating to accommodate required security monitoring. C. Tinted Heat reflective and low emissivity coated glass: 1. ASTM C1036, Type I, Class 2, Quality q3. 2. Color: 3. Thickness, / 6 mm (1/4 inch) / / as indicated /. SPEC WRITER NOTE: Spe
48、cify m1 where fire-protection rating is required. D. Patterned and Wired Flat Glass: 1. ASTM C1036, Type II, Class 1,Form 1, Pattern Pl, Finish F1, Quality / Q5 / / Q6 /, Mesh / m1 / / m2 /. 2. Thickness, / 6 mm (1/4 inch) / / as indicated /. 2.2 HEAT-TREATED GLASS SPEC WRITER NOTES: 1. Specify heat
49、 strengthened and fully tempered glass by thickness and ASTM C 1048 designations, and supplement standard for additional properties. Refer to information following end of Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-12-10 08 80 00-9 section for guides to ASTM C 1036
