ARMY MIL-DTL-60318 C (4)-2011 PROPELLANT M1 FOR USE IN CHARGE PROPELLING M67 FOR 105MM HOWITZER.pdf

相关资源

ARMY TT-C-490 F (1)-2013 CHEMICAL CONVERSION COATINGS AND PRETREATMENTS FOR METALLIC SUBSTRATES (BASE FOR ORGANIC COATINGS).pdf

ARMY MIL-W-13855 D (5)-2011 WEAPONS SMALL ARMS AND AIRCRAFT ARMAMENT SUBSYSTEMS GENERAL SPECIFICATION FOR.pdf

ARMY MIL-S-50312 (2)-2012 SHIPPING AND STORAGE CONTAINER CARTRIDGE 30 MILLIMETER - XM592.pdf

ARMY MIL-S-23389 B (3)-2012 SHIPPING AND STORAGE CONTAINER CARTRIDGE 20MM M548.pdf

ARMY MIL-R-71135 (4)-2012 RIFLE 5 56MM M16A2E3 (M16A3).pdf

ARMY MIL-PRF-914 C (1)-2008 RESISTOR NETWORKS FIXED FILM SURFACE MOUNT NONESTABLISHED RELIABILITY AND ESTABLISHED RELIABILITY GENERAL SPECIFICATION FOR《未设可靠度和已设.pdf

ARMY MIL-PRF-914 5 B (2)-2010 RESISTOR NETWORK FIXED FILM SURFACE MOUNT 16-PIN LEADLESS CHIP CARRIER NONESTABLISHED RELIABILITY AND ESTABLISHED RELIABILITY STYL.pdf

ARMY MIL-PRF-914 4 B (3)-2010 RESISTOR NETWORK FIXED FILM SURFACE MOUNT 20-PIN LEADLESS CHIP CARRIER NONESTABLISHED RELIABILITY AND ESTABLISHED RELIABILITY STYL.pdf

ARMY MIL-PRF-914 3 B (2)-2009 RESISTOR NETWORK FIXED FILM SURFACE MOUNT 16-PIN LEADLESS CHIP CARRIER NONESTABLISHED RELIABILITY AND ESTABLISHED RELIABILITY STYL.pdf

ARMY MIL-PRF-8565 16 (1)-2012 BATTERY STORAGE AIRCRAFT MEDIUM RATE MAINTENANCE-FREE 24-VOLT 5-AMPERE-HOUR.pdf

猜你喜欢

GOST 13104-1977 Leather raw material Determination of net mass and mass variation due to salting《制革原料 腌透性及净重测定法》.pdf

GOST 13105-1977 Leather raw material Methods of determination of the conservation components《制革原料 储存用的组份测定法》.pdf

GOST 13106-1967 Raw hides Histological and bacteriological control《生皮 组织和细菌控制》.pdf

GOST 13107-1979 Devices for speech reception and transmission Methods of measuring acoustic noeses《语言接收和传输装置 噪声测量方法》.pdf

GOST 13110-1983 Sheet stamping dies Lower plates-blanks for dies with diagonally positioned guide assemblies Construction and dimensions《带对角导柱和衬套的板材冲模用下料板 结构及尺寸》.pdf

GOST 13111-1983 Sheet stamping dies Upper plastic-blanks for dies with diagonally positioned guide assemdlies Design and dimensions《带对角导柱和衬套的板材冲模用上料板 结构及尺寸》.pdf

GOST 13112-1983 Die bases for cold plastic working dies with guide posts rear located Construction and dimensions《带后导柱和衬套的板材冲模用料板 结构及尺寸》.pdf

GOST 13113-1983 Die bases for cold plastic working dies with guide posts located on central line Construction and dimensions《带中间导柱和衬套的板材冲模用料板 结构及尺寸》.pdf

GOST 13114-1975 Die plate without shelves for cold plastic working dies Construction and dimensions《板材冲模用无托架料板 结构及尺寸》.pdf