1、 ISO 2017 Springs Shot peening Part 1: General procedures AMENDMENT 1 Ressorts Grenaillage de prcontrainte Partie 1: Modes opratoires gnraux AMENDEMENT 1 INTERNATIONAL STANDARD ISO 26910-1 First edition 2009-06-15 Reference number ISO 26910-1:2009/Amd.1:2017(E) AMENDMENT 1 2017-06 ISO 26910-1:2009/A
2、md.1:2017(E)ii ISO 2017 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopyi
3、ng, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749
4、01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.org ISO 26910-1:2009/Amd.1:2017(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out t
5、hrough ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO colla
6、borates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different appro
7、val criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives). Attention is drawn to the possibility that some of the elements of this document may be th
8、e subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).
9、 Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about IS
10、Os adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see the following URL: w w w . i s o .org/ iso/ foreword .html. This document was prepared by Technical Committee ISO/TC 227, Springs. A list of all parts in the ISO 26910 series can be found on t
11、he ISO website. ISO 2017 All rights reserved iii Springs Shot peening Part 1: General procedures AMENDMENT 1 Throughout the document Replace “this part of ISO 26910” with “this document”.Page iv, Foreword Replace the complete text of the foreword with the following: ISO (the International Organizati
12、on for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established ha
13、s the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The
14、procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the ed
15、itorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any paten
16、t rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. F
17、or an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see the following URL: w
18、w w . i s o .org/ iso/ foreword .html. This document was prepared by Technical Committee ISO/TC 227, Springs. A list of all parts in the ISO 26910 series can be found on the ISO website.Page 1, Clause 2 Replace the boilerplate text with the following: The following documents are referred to in the t
19、ext in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 26910-1:2009/Amd.1:2017(E) ISO 2017 All r
20、ights reserved 1 ISO 26910-1:2009/Amd.1:2017(E)Page 1, Clause 3 Replace the boilerplate text with the following: For the purposes of this document, the following terms and definitions apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Elec
21、tropedia: available at h t t p :/ www .electropedia .org/ ISO Online browsing platform: available at h t t p :/ www .iso .org/ obpPage 2 Replace the definition for 3.5 with the following: minimum time for which the successive increase of Almen arc height is 10 % or less for an additional exposure eq
22、ual to time t, i.e. a total time of 2t2 ISO 2017 All rights reserved ISO 26910-1:2009/Amd.1:2017(E) Page 14, Figure C.1 Correct the positions of lead lines as shown. Also, correct the pictorial way of the reference plane as shown. Dimensions in millimetres Replace the key table with the following: Key 1 4,76 steel ball 2 guide pin 3 measuring device (dial gauge, etc.) ISO 2017 All rights reserved 3 ISO 26910-1:2009/Amd.1:2017(E) ISO 2017 All rights reserved IC S 21.160 Price based on 3 pages
