1、ASD STANDARD NORME ASD ASD NORM prEN 3645-008 Edition P1 November 2005 PUBLISHED BY THE AEROSPACE AND DEFENSE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: 49.060 Descriptors: ENGLISH VERSION Ae
2、rospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling operating temperature 175 C or 200 C continuous Part 008: Non release plug with grounding ring Product standard Srie arospatiale Connecteurs lectriques circulaires contacts protgs, accouplement par filetage
3、pas rapide trois filets, tempratures dutilisation 175 Cou 200 C continu Partie 007 : Bouchon de vol pour fiche Norme de produit Luft- und Raumfahrt Elektrische Rundsteckverbinder, kontaktgeschtzt, Drei-gangige Gewinde-Schnellkupplung Dauerbetriebstemperaturen 175 C oder 200 CTeil 008: Schutzkappe fr
4、 freien Steckverbinder Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The Aerospace and Defense Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically appr
5、oved by the experts of the concerned Domain following member comments. Subsequent to the publication of this pre-standard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examina
6、tion and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national le
7、vel by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 30 November 2005 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2005 by ASD-STAN
8、 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 2 prEN 3645-008:2005Foreword This standard was reviewed by the Domain Technical Coordinator of AS
9、D-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. Contents Page 1 Scope3 2 Normative references.3 3 Terminology4 4 Required characteristics 4 4.1
10、Dimensions, mass4 4.2 Materials and surface treatment5 4.3 Electrical, mechanical and climatic characteristics5 5 Designation5 6 Marking.8 7 Technical specification 8 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo re
11、production or networking permitted without license from IHS-,-,-Page 3 prEN 3645-008:2005 1 Scope This standard specifies the characteristics of plugs with shielding rings in the family of circular, electrical connectors, with triple start threaded coupling. It applies to models in table 3. For cont
12、acts, filler plugs and rear accessories associated with this plug, see EN 3645-002. For receptacles and protective covers, see EN 3645-003, EN 3645-004, EN 3645-005, EN 3645-007, EN 3645-009 and EN 3645-010 respectively. These connectors are derived from and interchangeable with models W, F, J, M an
13、d K in specification MIL-DTL-38999/26. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated and unda
14、ted references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 3645-001, Aerospace series Connectors electri
15、cal, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 001: Technical specification 1) EN 3645-002, Aerospace series Connectors electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous
16、 Part 002: Specification of performance and contact arrangements 1)EN 3645-003, Aerospace series Connectors electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 003: Wall-mount receptacle Product standard 1)EN 3645-004, Aerospace ser
17、ies Connectors electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 004: Receptacle, hermetic, square flange mounting Product standard 1)EN 3645-005, Aerospace series Connectors electrical, circular, scoop-proof, triple start threade
18、d coupling, operating temperature 175 C or 200 C continuous Part 005: Receptacle, hermetic, round flange, brasage mounting Product standard 1)EN 3645-007 Aerospace series Connectors electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Par
19、t 007: Protective cover for plug Product standard EN 3645-009, Aerospace series Connectors electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 009: Receptacle, round flange, jam nut mounting - Product standard 1)EN 3645-010, Aerospa
20、ce series Connectors electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 010: Receptacle, hermetic, round flange, jam nut mounting - Product standard 1)MIL-DTL-38999/26, Connectors, electrical, plug, circular, straight, removable cr
21、imp contacts, series III, metric 2) 1)Published as AECMA Prestandard at the date of publication of this standard 2)Published by: Department of Defence (DOD), The Pentagon, Washington D.C. 20301 USA Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under licens
22、e with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 4 prEN 3645-008:2005 3 Terminology See EN 3645-001. 4 Required characteristics 4.1 Dimensions, mass Dimensions and tolerances are in millimetres. Key 1 Blue strip 2 Number of flats Figure 1 Plug Copyr
23、ight Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 5 prEN 3645-008:2005 Key 1 Blue strip 2 Number of slots Figure 2 Plug - Optional form for Models J and
24、M Table 1 - Plug - Dimensions Shell size B1 B2 H J K S Mass without contacts g max. +0,200 max. max. max. Models W, F Model K Models J, M 09 18,40 20,60 12 19,00 21,80 15 32 9 11 21,10 23,60 14 21,90 25,00 20 41 15 13 25,40 28,20 4 16 26,10 29,40 27 57 21 15 28,70 31,30 18 29,30 32,50 34 69 25 17 32
25、,20 34,50 20 32,80 35,70 37 72 29 19 34,90 37,30 22 35,50 38,50 48 94 38 21 38,10 40,50 824 38,70 41,70 55 105 42 23 41,10 43,70 26 41,70 44,90 67 117 51 25 44,30 46,80 28 44,90 48,00 71 121 57 4.2 Materials and surface treatment See Table 2. 4.3 Electrical, mechanical and climatic characteristics S
26、ee EN 3645-002. 5 Designation EXAMPLE: Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 6 prEN 3645-008:2005 Description block PROTECTIVE COVER ELE
27、CTRICAL CONNECTOR Identity block EN3645-F6GN35MA Number of the basic standard Model according to Table 2 Shell code for plug with shielded ring Shell size code according to Table 3 Letter indicating if the contact arrangement have grounded cavities or not Only N: no grounded cavity Contact arrangeme
28、nt according to EN 3645-002 Contact code according to Table 4 Polarisation: N, A, B, C, D, E NOTE: If necessary, the code I9005 shall be placed between the classification block and the identity block. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under lic
29、ense with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 7 prEN 3645-008:2005 Table 2 - Model coding Model Description W Sealed plugs, with shell in cadmium-plated aluminium alloy, olive green Salt spray resistance 500 h Plug with shielding ring- Crimped
30、 contacts Maximum operating temperature 175 C continuous J Sealed receptacles and plugs, with shell in cadmium-plated plastic composite, olive green - Salt spray resistance 2 000 h Plug with shielding ring Crimped contacts 1 500 operations Maximum operating temperature 175 C continuous K Sealed rece
31、ptacles, with shell in passivated stainless steel Salt spray resistance 500 h Plug with shielding ring Fire resistant Crimped contacts Maximum operating temperature 200 C continuous F Sealed plugs, with shell in nickel-plated aluminium alloy Crimped contacts Plug with shielding ring Maximum operatin
32、g temperature 200 C continuous M Sealed plugs, with shell in nickel-plated plastic composite Salt spray resistance 2 000 h Plug with shielding ring Crimped contacts 1 500 operations Maximum operating temperature 200 C continuous Table 3 - Shell size code Shell size Code 09 A 11 B 13 C 15 D 17 E 19 F
33、 21 G 23 H 25 J Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 8 prEN 3645-008:2005 Table 4 - Contact code Contacts Product marking Order coding
34、Supplied without contacts Supplied with contacts EN 3155-xxxx22-22 EN 3155-xxxx20-20 EN 3155-xxxx16-16 EN 3155-xxxx12-12 EN 3155-xxxx10-10 Male M A M Female F B F 6 Marking According to EN 3645-001. 7 Technical specification According to EN 3645-001. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
