1、AECMA STANDARD NORME AECMA AECMA NORM prEN 3661-006 Edition P 1 May 2005 PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8110 - Fax. + 32 2 775 8111 - www.aecma-stan.orgICS: 49.060 Descriptors: ENGLISH VERSION Aerospac
2、e series Circuit breakers, single-pole, temperature compensated, rated current 20 A to 50 A Part 006: With polarized signal contact Bus bar version Product standard Srie arospatiale Disjoncteurs unipolaires compenss en temprature, intensits nominales 20 A 50 A Partie 006 : Avec contact de signalisat
3、ion polaris Version pour barres bus Norme de produit Luft- und Raumfahrt Schutzschalter, einpolig, Temperaturkompensiert, Nennstrme von 20 A bis 50 A Teil 006: Mit polarisiertem Signalkontakt Sammelschienenversion Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibi
4、lity of AECMA-STAN (The European Association of Aerospace Industries - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestand
5、ard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of AECMA-STAN, it will be submitted as a draft European Standard (prEN)
6、to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with th
7、e EN. Edition approved for publication 31 May 2005 Comments should be sent within six months after the date of publication to AECMA-STAN Electrical Domain Copyright 2005 by AECMA-STAN Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANo
8、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3661-006:20052 Foreword This standard was reviewed by the Domain Technical Coordinator of AECMA-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of AECMA-STAN defined in A
9、ECMA-STANs General Process Manual, this standard has received approval for Publication. Contents Page 1 Scope . 3 2 Normative references 3 3 Dimensions and mass 3 4 Characteristics 5 5 Designation. 9 6 Rated current code. 10 7 Delivery codes. 10 8 Marking 10 9 Technical specification 10 Copyright As
10、sociation Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3661-006:20053 1 Scope This standard specifies the characteristics of single-pole circuit breakers, temperatur
11、e compensated with a rated current from 20 A to 50 A, used in aircraft on-board circuits at a temperature between 55 C and 125 C and at an altitude of 15 000 m max. These circuit breakers are operated by a push-pull type single push button (actuator), with delayed action “trip-free“ tripping with a
12、polarized signal contact which is open when main contacts are closed, and inversely. They are connected on supply side by means of bus-bar.They will continue to function up to the short-circuit current. 2 Normative references The following referenced documents are indispensable for the application o
13、f this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3155-016, Aerospace series Electrical contacts used in elements of connection Part 016: Contacts, electrical, male, type
14、 A, crimp, class S Product standard.1)EN 3661-001, Aerospace series Circuit breakers, single-pole, temperature compensated, rated current 20 A to 50 A Part 001: Technical specification.1)EN 3841-305, Aerospace series Circuit breakers Test methods Part 305: Short-circuit performance. EN 6113, Aerospa
15、ce series Circuit breaker, connecting and attachment hardware.1)TR 6083, Aerospace series Cut-outs for installation of electrical components.2)MIL-I-81969/1A, Installing and removal tools, connector electrical contact, type III, class 2, composition C.3)MIL-I-81969/14C, Installing and removal tools,
16、 connector electrical contact, type III, class 2, composition B.3)MIL-S-19500, Semiconductor device, diode, silicon, fast recovery.3)FED-STD-595B, Colours used in Government Procurement. 3 Dimensions and mass 3.1 Dimensional characteristics The circuit breakers do not have to correspond to the picto
17、rial illustration, only the dimensions given shall be adhered to. Dimensions are in millimetres. See Figure 1. 1) Published as AECMA Prestandard at the date of publication of this standard 2) Published as AECMA Technical Report at the date of publication of this standard. 3) Published by: Department
18、 of Defense (DOD), the Pentagon, Washington D.C. 20301 USA. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3661-006:20054 1155323M12 x 0,75 10,4
19、0,43 min.2 0,3482519,5 max.34 max.42 max.10 min.10 min.10 9,2 0,3926,5 0,3180-123 148 128 max.6,6 0,64533 max.401325 max.7120-1 5 ,5+0,106129,5 0,1 248,2 0,515,1 min.r 2F2F1 and F2 : see EN 3661-001, table 3F1Bus-bar side40,2 max.550+1Key 1 Push button released 9 1 to 3 max. 2 Green colour according
20、 to FED-STD-595B No. 34090 10 3 White Gauge 20 connection pins according to EN 3155-016M2018 4 Marking area, see Clause 8. 11 Indicative value 30 5 (see note) 5 Connecting screw and washer 12 6 Push button pressed Positioning lug in accordance with the panel cut-out, as per TR6083C202 7 Lockwasher 1
21、3 Rated current marking (white on green) 8 Attachment nut NOTE Tools noted in Subclause 4.2.4 shall be applied without interfering with the terminal 2 connection. Even if the circuit breakers are grouped. Figure 1 Configuration Dimensions Tolerances F1 and F2: see EN 3661-001, Table 3. Copyright Ass
22、ociation Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3661-006:20055 3.2 Electrical diagram See Figure 2. Terminal No.: 1 and 2: Main contacts 3 and 5: Signal contac
23、ts Figure 2 Electrical diagram 3.3 Mass 75 g max. (delivery code A including hardware). 3.4 Panel mounting See EN 3661-001. 4 Characteristics 4.1 Material, surface treatment See EN 3661-001. 4.2 Mechanical characteristics 4.2.1 Fasteners See EN 6113. 4.2.2 Recommended tightening torque of attaching
24、nut for installation (5,25 0,25) Nm. 4.2.3 Recommended tightening torque of connection hardware for installation (2,35 0,15) Nm. 4.2.4 Recommended tools for contacts of auxiliary contact insertion and extraction plastic MIL-I-81969/14-11; metallic MIL-I-81969/1-02. 213 5Push-button released213 5Push
25、-button pressed3 5or3 5orCopyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3661-006:20056 4.2.5 Resistance to vibrations 4.2.5.1 Combined test: ambi
26、ent temperature at 70 C and vibrations Sinusoidal: 10 gn, see EN 3661-001. Random: 5,8 gn, see EN 3661-001. Low frequencies: 10 gn, see EN 3661-001. 4.2.5.2 Combined test: ambient temperature at 85 C, altitude and vibrations Sinusoidal: 3 gn, see EN 3661-001. 4.2.6 Resistance to shocks 50 gn, see EN
27、 3661-001. 4.2.7 Mechanical endurance See Table 6. 4.3 Environment characteristics 4.3.1 Humidity See EN 3661-001. 4.3.2 Corrosion See EN 3661-001. 4.3.3 Contaminating fluids See EN 3661-001. 4.3.4 Over-voltage caused by lightning See EN 3661-001. 4.4 Electrical characteristics 4.4.1 Nominal voltage
28、s of main contacts See Table 1. Table 1 28 V d.c. 26 V a.c., 360 Hz to 800 Hz Nominal voltage 115 V a.c., 360 Hz to 800 Hz Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without l
29、icense from IHS-,-,-prEN 3661-006:20057 4.4.2 Diode of signal contact characteristic Maximum current at 125 C : 0,5 A. Peak repetitive reversal voltage: 800 V min. Quality standard: JANTX according to MIL-S-19500. 4.4.3 Voltage drop at nSee Table 2. Table 2 Ratings A 20 25 30 35 40 45 50 U max. at n
30、 V 0,15 0,15 0,15 0,15 0,12 0,12 0,12 Signal circuit : 28 V d.c.; I = 3 mA : U 1,0 V. NOTE When a signal contact has been operated with a power greater than 60 mW and/or with a voltage higher than 28 V d.c., it loses its low current quality. 4.4.4 Minimum and maximum tripping thresholds See Table 3.
31、 Table 3 Overload (in % of n) Minimum thresholds value 1 h Maximum thresholds value 1 h Ambient temperatures C Ratings On ground At 15 000 m On ground 23 5 110 105 145 55 5 110 105 165 70 5 105 100 145 125 5 All 90 80 145 4.4.5 Overload trip See Table 4. Copyright Association Europeene des Construct
32、eurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3661-006:20058 Table 4 Overload (in % of n) 200 500 1 000 Ambient temperatures C Ratings A Trip time s 23 5 4 to 15 55 5 70 125 5 All 1,5 0,15
33、to 2,50 0,045 to 0,600 4.4.6 Short-circuit values See Table 5. Table 5 Nominal voltage 28 V d.c. 115 V a.c., 360 Hz to 800 Hz 0,8 cos 1 Prospective currents 4 000 A L/R 1 ms 2 000 A r.m.s. Test altitudes On the ground and at maximum altitude (15 000 m, 12 100 Pa) Number of operations 1 CO a+ 2 OCO b
34、aBreak operation (for definition see EN 3841-305). bMake operation (for definition see EN 3841-305). 4.4.7 No-load and load endurance See Table 6. Table 6 Number of operations to be provided No-load Load 5 000 2 500 2 500 2 500 2 500 Main contacts Applicable Not applicable Resistive n, 28 V d.c. Ind
35、uctive L/R = 5 ms n, 28 V d.c. Inductive 0,6 cos 0,7n, 115 V a.c. - 360 Hz to 800 HzAll ratings Signal contacts ApplicableResistive 3 mA, 28 V d.c. Resistive 3 mA, 5 V d.c. Lamp 0,2 A, 28 V d.c. Resistive 0,5 A, 28 V d.c NOTE 1 One operation corresponds to one closing + one opening. NOTE 2 Tolerance
36、s 5 % on current, voltage and frequency values. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3661-006:20059 4.4.8 Dielectric rigidity See Table
37、 7. Table 7 Closed position Z = 0 m Z = 15 000 m 1 and 2 with attachment 1 and 2 with 3 1 and 2 with 5 1 500 V 400 V 3 with 5 3 and 5 with attachment 500 V 150 V Open position Z = 0 m Z = 15 000 m 1 with 2 1 and 2 with attachment 3 and 5 with 1 3 and 5 with 2 1 500 V 400 V 3 and 5 with attachment 50
38、0 V 150 V 4.4.9 Insulation resistance According to EN 3661-001, Table 5. 5 Designation EXAMPLE Description block CIRCUIT BREAKER Identity block EN3661-006A20AA Number of EN standard Design code, A: green button Rated current code (see Table 8) Delivery code A (see Table 9) NOTE If necessary, the cod
39、e I9005 shall be placed between the description block and the identity block. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3661-006:200510 6 Ra
40、ted current code See Table 8. Table 8 Rating current n (A) 20 25 30 35 40 45 50 Marking on actuator 20 25 30 35 40 45 50 Rated current code 20A 25A 30A 35A 40A 45A 50A 7 Delivery codes See Table 9. Table 9 Connection and attachment hardware kits EN 6113 Delivery conditions Delivery code Kit part-No.
41、 aIncluded parts Pieces per part Fitted Supplied separately Connecting screw 2 Connecting lock washer 2 Attachment nut 1 A EN 6113A Attachment lock washer 1 X Attachment nut 1 B EN 6113B Attachment lock washer 1 X aSpare parts could be ordered separately, informations see EN 6113. 8 Marking As defin
42、ed on the drawing and unless otherwise specified by contract, marking shall include: the designation defined in Clause 5 (without delivery hardware code), on the packaging; the manufacture date (year, week); the manufacturers name or trademark; the electrical diagram and the terminal identification;
43、 the manufacturers part number (corresponding to the part number with connection and attachment hardware). NOTE The marking could be combined on the both opposite faces. For electrical diagram and/or terminal identification see Figure 1. 9 Technical specification See EN 3661-001. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
