AIR FORCE AF AFP AFMC 10-1403-2011 AIR MOBILITY PLANNING FACTORS.pdf

上传人:sofeeling205 文档编号:427216 上传时间:2018-11-07 格式:PDF 页数:29 大小:608.56KB
下载 相关 举报
AIR FORCE AF AFP AFMC 10-1403-2011 AIR MOBILITY PLANNING FACTORS.pdf_第1页
第1页 / 共29页
AIR FORCE AF AFP AFMC 10-1403-2011 AIR MOBILITY PLANNING FACTORS.pdf_第2页
第2页 / 共29页
AIR FORCE AF AFP AFMC 10-1403-2011 AIR MOBILITY PLANNING FACTORS.pdf_第3页
第3页 / 共29页
AIR FORCE AF AFP AFMC 10-1403-2011 AIR MOBILITY PLANNING FACTORS.pdf_第4页
第4页 / 共29页
AIR FORCE AF AFP AFMC 10-1403-2011 AIR MOBILITY PLANNING FACTORS.pdf_第5页
第5页 / 共29页
亲,该文档总共29页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、 BY ORDER OF THE SECRETARY OF THE AIR FORCE AIR FORCE PAMPHLET 10-1403 12 DECEMBER 2011 Operations AIR MOBILITY PLANNING FACTORS COMPLIANCE WITH THIS PUBLICATION IS MANDATORY ACCESSIBILITY: This publication is available by downloading from the e-Publishing website at www.e-Publishing.af.mil RELEASAB

2、ILITY: There are no releasability restrictions on this publication OPR: HQ AMC/A3XP Supersedes: AFPAM 10-1403, 18 December 2003 Certified by: Deputy AF/A5R (Col Michael W. Hafer) Pages: 29 This pamphlet supersedes AFPAM 10-1403 dated 18 December 2003 Air Mobility Planning Factors. It provides broad

3、air mobility planning factors for peacetime and wartime operations. It is designed to help service, joint, and combined planners make gross estimates about mobility requirements in the early stages of the planning process. It covers strategic airlift, air refueling, and aeromedical evacuation (AE).

4、For greater detail, or in-depth mobility analysis call HQ AMC/A3XP at DSN 779-4363/3382 or 618 TACC/XOP at DSN 779-1930. Refer recommended changes and questions about this publication to the Office of Primary Responsibility (OPR) via AF Form 847, Recommendation for Change of Publication; route AF Fo

5、rm 847s from the field through the appropriate functionals chain of command. Ensure that all records created as a result of processes prescribed in this publication are maintained in accordance with AFMAN 33-363, Management of Records, and disposed of in accordance with the Air Force Records Disposi

6、tion Schedule (RDS) located at https:/www.my.af.mil/afrims/afrims/afrims/rims.cfm SUMMARY OF CHANGES Air mobility planning data contained within the tables of this document (including but not limited to aeromedical evacuation data, aircraft payload, ground times, primary mission aircraft inventory,

7、airfield throughput and fuel burn rates) has been substantially revised (indicated by a margin bar) and should be completely reviewed for impacts on existing plans. Table 13, Aeromedical Evacuation Capabilities Matrix, has been added to assist AE force identification and AE planning efforts. Provide

8、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2 AFPAM10-1403 12 DECEMBER 2011 Section AMobility Planning 3 1. How To Use This Pamphlet . 3 Section BAirlift Formulas 3 2. Number of Cargo Missions Required 3 3. Number of Passenger (PAX) Missions Required 3

9、4. Total Missions Required 3 5. Time to Arrival 3 6. Cycle Time . 4 7. Closure . 4 8. Fleet Capability 4 9. Fleet Capacity 4 10. Airfield Throughput Capability (station capability) 4 Section CAir Refueling Formulas 4 11. Air Refueling Overview . 5 Section DAeromedical Evacuation Formulas 5 12. Aerom

10、edical Evacuation Overview . 5 Section EExamples 6 13. Airlift Example. . 6 14. Air Refueling Example. . 8 15. Aeromedical Evacuation Example. 9 Table 1. Aircraft Airfield Restrictions . 10 Table 2. Aircraft Size . 11 Table 3. Aircraft Payloads1. 12 Table 4. Aircraft Block Speeds 13 Table 5. Ground

11、Times 14 Table 6. Aircraft Utilization. 15 Table 7. Productivity Factors . 16 Table 8. Maximum Airfield Throughput . 16 Table 9. Fuel Burn Rates . 17 Table 10. Tanker Offload Capabilities . 17 Table 11. KC-135 Tanker Aircraft Required.1,2,3 18 Table 12. KC-10 Tanker Aircraft Required.1,2,3 19 Provid

12、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AFPAM10-1403 12 DECEMBER 2011 3 Table 13. Aeromedical Evacuation Capabilities Matrix. . 20 Table 14. Aeromedical Evacuation Capabilities 21 Attachment 1GLOSSARY OF REFERENCES AND SUPPORTING INFORMATION 22 Sec

13、tion A Mobility Planning 1. How To Use This Pamphlet 1.1. There are four basic parts to this pamphlet: terms and definitions, formulas, planning factors, and examples. Although each of these parts can be individually used, we recommend you review the entire contents to get a full understanding of th

14、e planning process. 1.2. Due to the number of variables involved in every air mobility operation, the planning factors presented are not universally applicable. Instead, they provide order of magnitude approximations in the context of a generic scenario. The use of detailed computer simulation model

15、s is encouraged for extensive calculations. 1.3. This pamphlet only addresses objective planning computations. It does not provide guidance concerning other factors such as environmental and tactical considerations which can impact the mobility operation. Section B Airlift Formulas 2. Number of Carg

16、o Missions Required 3. Number of Passenger (PAX) Missions Required NOTE: PAX on Cargo Missions = Number of PAX seats available on each cargo mission x Number of Cargo Missions. 4. Total Missions Required = Cargo missions + PAX missions 5. Time to Arrival = active route flying time (ARFT) + active ro

17、ute ground time (ARGT) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4 AFPAM10-1403 12 DECEMBER 2011 6. Cycle Time = round trip flying time (RTFT) + round trip ground time (RTGT) 7. Closure NOTE: For major wartime operations, we recommend planners

18、use the wartime objective surge UTE rates published in Table 6. For non-mobilized contingencies, we recommend the contingency UTE rates published in Table 6. The computations involved in determining actual UTE rates are quite involved and not necessary for initial gross planning estimates. 8. Fleet

19、Capability Short tons delivered to the theater per day NOTE: This formula is preferred for contingency planning because it accurately relates the variables affecting the deployment of requirements. 9. Fleet Capacity Million ton-miles per day NOTE: Although planners do not commonly use this formula,

20、occasionally we need to convert short ton figures into million ton-miles per day (MTM/D). AMC force structure programmers use MTM/D when funding out-year aircraft purchases and many civilian agencies are accustomed to visualizing our fleet capability in terms of MTM/D. Fleet Capacity is generally mo

21、re optimistic than actual Fleet Capability for a particular contingency. 10. Airfield Throughput Capability (station capability) NOTE: Use the lower of the working, parking, or fuel MOG. Section C Air Refueling Formulas Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

22、ense from IHS-,-,-AFPAM10-1403 12 DECEMBER 2011 5 11. Air Refueling Overview Refer to Table 10, Table 11, and Table 12 for determining the approximate number of tankers required to meet the air refueling requirements for various size fighter/airlift deployments. These tables were constructed using a

23、verage/historical data and will provide a gross estimate of the size and duration of an air refueling operation. If actual mission specifics and data are known, such as aircraft model, configuration, air refueling altitude, airspeed, tanker basing, etc, using the formulas below will provide more acc

24、urate planning estimates. However, this formula does not consider specific air refueling abort reserves and the impact on destination fuel. As stated in the introduction we recommend using computer simulation models whenever feasible. 11.1. Offload Required (per receiver) Distance = total distance f

25、rom takeoff to landing TAS = average airspeed of receiver leg (use Table 4 Aircraft Block Speeds or applicable flight manual airspeeds for other aircraft.) Fuel Flow = fuel burn rate in lbs/hr Total Fuel = total fuel on board at takeoff Destination Reserve = required fuel reserves at destination 11.

26、2. Offload Available (per tanker) 11.3. Tankers Required Section D Aeromedical Evacuation Formulas 12. Aeromedical Evacuation Overview Refer to AFI 11-2AE V3 Addenda A for detailed aircraft specific configuration and mission planning. Use the following formulas and data in Table 14 to determine the

27、AE force and capabilities. In the near term, AE will be primarily accomplished using, C-21, C-130, KC-135, or C-17 aircraft. Opportune airlift may be used, keeping the best interest of the patient and crew in mind. When the aeromedical segment (Stage II or Stage III) of the Civil Reserve Air Fleet (

28、CRAF) is activated, the B-767 will be the primary means of intertheater AE, with augmentation by military aircraft such as KC-135 and C-17, as necessary. An AE crew consists of two (2) flight nurses and three (3) medical technicians. 12.1. AE Missions (# required per day) Provided by IHSNot for Resa

29、leNo reproduction or networking permitted without license from IHS-,-,-6 AFPAM10-1403 12 DECEMBER 2011 Aircraft Load Planning Factor = standard number of patients loaded per aircraft for aeromedical evacuation (see Table 14). 12.2. AE Crew (# required for missions flown, does not include stage) Crew

30、s per Aircraft: Refer to Table 14 Crew Cycle Time: Intratheater (Within Theater) = 2 days Intertheater (Theater to CONUS) = 4 days Section E Examples 13. Airlift Example. As an example of how to use the formulas and planning factors in this pamphlet, assume the following scenario. The 10th Mountain

31、Div. out of Ft. Drum, NY, is to deploy to Kathmandu, Nepal, at the foot of the Himalayas, to assist in earthquake relief. The requirement is to move 700 personnel and 800 short tons of cargo. NOTE: The following examples use International Civil Aviation Organization (ICAO) codes, which are four-char

32、acter alphanumeric code designating each airport around the world and commonly used in flight planning. 13.1. Suitable Airfield 13.1.1. Referring to the Aircraft Airfield Restrictions (Table 1), we see that the B-767 requires a minimum of 6,000 feet of runway and the C-17 requires a minimum of 3,500

33、 feet. Since the airfield at Ft. Drum, Wheeler-Sack AAF, has a runway length of 10,000 feet, it meets the requirements for both aircraft (this assumes adequate runway width). NOTE: Refer to the HQ AMC Airfield Suitability and Restrictions Report (ASRR) or the airfield database (AFD) in AMCs Global D

34、ecision Support System (GDSS) to determine suitability for mobility aircraft (C-5, C-17, C-21, C-130, KC-10, KC-135). If the airfield does not appear in the ASRR/AFD, contact AMC/A3AS and request the airfield be evaluated and added to the database (Airfield.Helpdeskamc.af.mil). AMC/A3AS will provide

35、 prompt feedback and include suitability information in future editions of the ASRR. 13.1.2. Looking in the Kathmandu area, we find Tribhuvan International airport in Kathmandu to have 10,121 feet of runway which, along with the associated taxiways and ramp, is stressed for B-767 aircraft. Therefore

36、, we make our initial plans based on using Wheeler Sack AAF as the onload and Tribhuvan International as the offload. 13.2. Missions Required. Our examples will address only the cargo requirements, however passenger movement would be handled in a similar manner. For all examples to follow, assume we

37、 have 15 C-17s apportioned for our use and we will use crew staging where necessary. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AFPAM10-1403 12 DECEMBER 2011 7 13.3. Time to Arrival. The time required for cargo/PAX to arrive at the offload locat

38、ion including all en route ground times. For this example, the C-17s will depart McGuire (KWRI), fly to Wheeler Sack AAF (KGTB) for onload, then en route stop at Rota (LERT), Dhahran (OEDR), Delhi, (VIDP), and then offload at Tribhuvan (VNKT). Refer to definitions and tables as needed. = active rout

39、e flying time (ARFT) + active route ground time (ARGT) NOTE: First leg from McGuire to Wheeler is inactive as its a positioning leg. Block speeds were interpolated from Table 4. (refer to Table 5.) = 26.55 hours 13.4. Cycle Time. For this example, we calculated round trip flying time (RTFT) and roun

40、d trip ground time (RTGT) using reverse routing except the last leg will be from Rota (LERT) to McGuire (KWRI). Refer to definitions for RTFT and RTGT. Cycle Time = round trip flying time (RTFT) + round trip ground time (RTGT) Provided by IHSNot for ResaleNo reproduction or networking permitted with

41、out license from IHS-,-,-8 AFPAM10-1403 12 DECEMBER 2011 = 20 hours 13.5. Closure = 3.8 days 13.6. Fleet Capability (short tons delivered to the theater) = 208.8 Stons/day 13.7. Airfield Throughput Capability It is necessary to look at the throughput capability of all airfields associated with a dep

42、loyment, to determine whether any one airfield limits a planned operation. However, for initial planning, the en route locations may be assumed to have a higher throughput capability than the onload and offload locations. For this example, we have used Tribhuvan International and a working MOG of on

43、e narrow body (NB) aircraft. Airfield Throughput Capability (e.g, Tribhuvan) = 282.5 Stons/day (Refer to Table 8.) NOTE: Since the arrival airfield can handle the estimated fleet capability that will be delivered, this calculation is complete. If the fleet capability had exceeded the airfields throu

44、ghput, either the flow would need to be slowed to compensate or the airfields resources increased to handle the airflow. 14. Air Refueling Example. For this example, assume you need to deploy 6 F-15Cs from Langley (KLFI) to Spangdahlem (ETAD). How much fuel and how many tankers (KC-135R) are Provide

45、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AFPAM10-1403 12 DECEMBER 2011 9 required? Note: For this example average/historical figures were used. Actual numbers would vary according to aircraft model, configuration, altitude, airspeed, etc. 14.1. Onloa

46、d Required (per receiver) Distance = total distance from takeoff to landing TAS = average airspeed of receiver leg (use Table 4. for mobility aircraft or applicable flight manual airspeeds for other aircraft.) Fuel Flow = fuel burn rate in lbs/hr Total Fuel = total fuel on board at takeoff Destinati

47、on Reserves = required fuel reserves at destination = (3500/480 x 10,822) - 23,000 + 7500 = 63,410 lbs (per receiver) x 6 = 380,462 lbs 14.2. Offload Available (per tanker) = 71,848 lbs per tanker 14.3. Tankers required = 380,462 (rounded up) 71,848 = 6 KC-135Rs required 15. Aeromedical Evacuation E

48、xample. For this example, C-130s will be used to evacuate 500 patients per day. 15.1. AE Missions (# required) = 10 AE Missions required Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-10 AFPAM10-1403 12 DECEMBER 2011 Table 1. Aircraft Airfield Restrictions Aircraft Type Min Runway for Landing1 Min Taxiway Width (ft) Aircraft Classification Number2,3 Aircraft Classification Number2,3 Rigid Pavement Subgrades Flexible Pavement Subgrades Length (ft) Width (ft) High Med Low Ultra Low High Med Low U

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1