1、 IND-STD ANSI/AIIM MS3Y -90 NOTICE I ED 7999998 0005L9L b NOTICE OF ADOPT ION ANSI/AIIM MS34-1990 NOTICE 1 12 August 1992 Non-Governinent Standard, ANSI/AIIM MS34-1990, adopted on 12 August 1991 is approved for use by dll Department of Defense (DoD) activities. The Association for Inforinatiori and
2、Image Management (AIIM), Coininittee C11, developed and prepared ANSI/AIIM MS34-1990; the American National Standards Institute (ANSI) certified it as an American National Standard on 16 Noveinber 1990. Both ANSI and AIIM have furnished clearances required by existing regulations. The Naval Publicat
3、ions and Forms Center (NPFC), Standardization Docuiiients Order. Desk, Bldg 4D, 700 Robbins Ave, Philadelphia PA 19111-5094 will stock ANSI/AIIM MS34-1990 only for issue to DoD dctivities. All other users niust purchase copies froin: Association for Information and iinage Management (AIIM) 1100 Wayn
4、e Avenue, Suite 1100 Silver Spring, MD 20910 (301) 587-8202 Title of Standard: late of Specific Issue Adopted: Dimensions for Reels Used f-or 16inm dnd 35inni MicrofiTm 16 Novcrnber 1390 Releasing Non-Government Standards Lody: AIIM NOTE: When reaffirmation, revision, or cancellation action is initi
5、ated, AIIM shall notify the Military Coordinating Activity (MCA), identify the specific action, and request MCA participation. Custodians: .4ir Force - 16 Army - CR Navy - AS DLA - DH Military Coordinating Activity Air Force - 16 (Project No. EDRS-l28) Review activities: Air Force - 11, 14, 18, 19 A
6、riiiy - AR, AT, MI, SC riavy - SA, SH, TD DLA - CS, ES, GS, IS AREA EDRS DISTRIBUTION STATEMENT A. Approved for pub1 ic release; distribution is un1 iinited. a AIIM MS34 90 = LO12348 O000264 1 I- ANSI/AIIM MS34-1990 Dimensions for Reels Used for 16 mm and 35 mm Microfilm 0 O Q) Q) r r 1 r .- I O 1 I
7、 Approved As November 16, 1990 Association for Information and Image Management 1100 Wayne Avenue, Suite 1100 Silver Spring, Maryland 2091 O -Telephone 301 1587-8202 Standard for Information and Image Management - Dimensions for Reels Used for 16 mm and 35 mm Microfilm Association for Information an
8、d Image Management AIIM MS34 90 = 10123YB 00002b5 3 ANSI/AIIM MS34-1990 O e O This standard covers the essential dimensions of ggh&ve®ls made of plastic or metal used for the storage and retrieval of processed 16 mm and 35 mm microfilm that is used in manually threaded equipment. AIIM MS34 90 W 1
9、012348 O000266 5 Table of Contents Foreword., i Management had the following members: At the time this standard was approved, the Standards Board of the Association for Information and Image 1 Scope . 1 2 References . 1 2.1 Referenced American National Standards . 1 2.2 Related American National Sta
10、ndards 1 3 Requirements 1 3.1 16 mm Reels . 1 3.2 35 mm Reels . 1 3.3 Lateral Runout . 1 3.4 Flanges 1 3.5 Finish . 1 3.6 Optional Features . 1 Marilyn Courtot, Chair Thomas E. Berney Don Kiosterboer E. Bnen Lewis Alan S. Linden Wesley J. Micket Charles A. Plesums L. Don Prince George Thoma Charles
11、F. Touchton Herbert J. White II Figures The AIIM Supply Items Committee, C11, processed Figure 1 Reel 2 Figure 2 Spindle Holes 2 and approved this standard. The following were members of the committee at the time of approval: Tables Table 1 Dimensions for 16 mm and 35 mm Reels . 2 Foreword (This for
12、eword is not part of American National Standard for Information and Image Management-Dimensions for Reels Used for 16 mm and 35 mm Microfilm, ANSI/AIIM MS34- 1990.) There is an increasing variety of equipment available to retrieve 16 mm and 35 mm roll microfilm. Some use conventional threading from
13、the supply reel to the take-up reel in order to drive the microfilm. Other equipment uses automatic threading techniques with reels and an ANSI- approved cartridge. Organization Consultant Canon USA, Inc. Fuji Photo Film U.S.A., Fuji Photo Film U.S.A., Genealogical Society of HQ AFLC/MMTIB James Riv
14、er Graphics Microseal Corp. City of New York 3M Company 3M Company Tuscan Industries Zytron Corp. Inc. Inc. Utah Representative Thomas E. Berney, Chair Tony Fujinuma Greg Pelican Shin Aizeki Eric Erickson Geo Biach Louis Spelios Thomas Graves Harold H. Dorfman Carl J. Anderson Marvin Schmitz Peter G
15、eil William Neale The intent of this standard is to provide 16 mm and 35 mm reel dimensions which will allow compatibility with readers using conventional threading and which can also be used for microfilm storage. If a 16 mm reel wili be used in a cartridge for use in automatic threading equipment,
16、 the requirements of ANSI/AIIM MS15-1990 will apply. This standard replaces ANSI PH5.6-1968 (R1974). i American National Standard for Information and Image Management-Dimensions for Reels Used for Processed 16 mm and 35 mm Microfilm, ANSI/AIIM MS34-1990 1 Scope This standard covers the essential dim
17、ensions of lightweight reels made of plastic or metal used for the storage and retrieval of processed 16 mm and 35 mm microfilm that is used in manually threaded equipment. Camera spools are also frequently used for storing pro- cessed microfilm. The dimensions for these spools are not included in t
18、his standard but may be found in ANSI/AJJM MS29- 1987. 2 References All standards are subject to revision. When the follow- ing documents are superseded by an approved revision, that revision may apply. 2.1 Referenced American National Standards ANSI/AIIM MS29-1987. Information and Image Manage- men
19、t-Cores and Spools for Recording Equipment- Dimensions. 2.2 Related American National Standards ANSI IT9.2-1989. Imaging Media-Photographic Pro- cessed Films, Plates, and Papers-Filing Enclosures and Storage Containers. ANSI PH1.33-1986. Photography (Fh)-16 mm 100 Foot, 16 mm 200 Foot, 35 mm 100 Foo
20、t, and 70 mm 100 Foot Spools for Recording Instruments, Microfilms, and Still-picture Cameras-Dimensions, ANSI/AIIM MS15-1990. Dimensions and Operational Constraints for Single Core Cartridge for 16 mm Processed Microfilm, 1 AIIM MS34 90 W 10123Y8 00002b7 7 W I 3 Requirements 3.1 16 mm Reels. The in
21、side surface of the flange shall be in the same plane as the location surface around the square spindle hole. The ailowable deviation from this align- ment, measured within 3.2 mm (0,126 inch) of the core, shall be k0.25 mm (0.010 inch). The minimum diameter of the location surface around the square
22、 spindle hole shall be 15.9 mm (0.626 inch), the maximum diameter shall be 17.0 mm (0.669 inch). These specifications apply to front and rear flanges if both have square spindle holes. (See Figures 1 and 2, in addition to Table 1.) 3.2 35 mm Reels. The position of the inside surface of the flange wi
23、th respect to the location surface around the square spindle hole shall be 1.0 f 0.5 mm (0.039 inch f 0.020 inch). The minimum diameter of the location surface around the square spindle hole shall be 15.9 mm (0.626 inch), the maximum diameter shall be 17.0 mm (0.669 inch). These specifications apply
24、 to front and rear flanges if both have square spindle holes. (See Figures 1 and 2, in addition to Table 1.) 3.3 Lateral Runout. The lateral runout (wobble) of the reel from the intended plane of rotation shall not exceed 1.3 mm (0.052 inch). The “intended plane” is a plane perpen- dicular to the ax
25、is of the spindle and coincident with the outer surface of the flange at points adjacent to the spin- dle. When the reel is rotated on an accurate tighf-fitting spindle, the outward or inward excursion of the flange from this intended plane shall not exceed 1.3 mm (0.052 inch). 3.4 Flanges. The flan
26、ges may be either solid or spoked (with open areas). 3.5 Finish. The reel shall be free of any flashing or molding lines that would interfere with the film transport or cause damage to the film. 3.6 Optional Features. An optional film loading slot is allowed in the reel core. If used, the width of t
27、his slot shall conform to dimension K (see Figure 1, in addition to Table 1). An optional film loading slot is also permitted in either one or both flanges. If used, the width of this slot will also conform to dimension K. AIIM MS34 I K / I 1 Lr+-, , / I II I 5-f I II Il I ,Q II ,I I I II I II AB I
28、II il 1 I I L“:“. LOCATING SURFACT-“ I SECTION X-X Figure 1. Reel Table 1. Dimensions for 16 mm and 35 mm Reels 90 W Loi12348 O000268 i REAR FLANGE ksi FRONT FLANGE STYLE 1 (FOR 16 MM AND 35 MM REELS) 16 mm Reels Millimeters Inches A. 17.0 +1.5 0.67 +0.06 *B. 21.4 Max. 0.843 Max. - 0.9 - 0.035 C. 0.
29、00 +0.25 O.OO0 +0.010 D. 32.0 f 1.0 1.26 +OM E. 92.0 +2.0 3.62 +O.OS - 1.0 - 0.04 35 mm Reels Mulimeters Inches 36.0 +1.5 1.42 +0.06 40.2 Max. 1.583 Max. 1.0 20.5 0.04 I0.02 32.0 + 1.0 1.26 +0.04 -0 -0 92.0 +2.0 3.62 +O.OS - 1.0 - 0.04 - 0.9 - 0.038 (FOR 35 MM REELS) (FOR 16 MM REELS) +The front fla
30、nge is the one that first engages the Holes are oriented as seen by looking at outer equipment spindle. surface of each flange separately. Figure 2. Spindle Holes 16 mm Reels 35 mm Reels Millimeters Inches Millimeters Inches G. 3.3 110.2 0.13 10.008 3.3 10.2 0.13 +0.008 H. 8.1 10.5 0.32 10.02 8.1 k0
31、.5 0.32 I0.02 J. 8.1 +0.2 0.32 +0.008 8.1 +0.2 0.32 +0.008 - 0.5 - 0.02 - 0.5 - 0.02 S. 8.1 +0.2 0.32 +0.008 8.1 +0.2 0.32 +0.008 - 0.5 - 0.02 - 0.5 - 0.02 “. 1.3 +1.0 0.05 +0.04 1.3 +1.0 0.05 +0.04 - 0.5 - 0.02 -0.5 - 0.02 * Dimension B is the width outside the flanges including any embossed area *
32、 Optional 2 AIIM MS34 90 W 1012348 0000269 O W ANSIIAIIM MS34-1990 by Association for Information and Image Management 1100 Wayne Avenue, Suite 1100 Silver Spring, MD 20910 Tel: 301 1587-8202 I Fa: 301 1587-271 1 ISBN 0-89258-21 2-X Printed in the United States of America AIIM MS34 90 3032348 0000270 7 ISBN O-89258-212-X December 1990
