ANSI ICEA P-45-482-2017 SHORT CIRCUIT PERFORMANCE OF METALLIC SHIELDS AND SHEATHS ON INSULATED CABLE.pdf

上传人:postpastor181 文档编号:434902 上传时间:2018-11-11 格式:PDF 页数:15 大小:1.22MB
下载 相关 举报
ANSI ICEA P-45-482-2017 SHORT CIRCUIT PERFORMANCE OF METALLIC SHIELDS AND SHEATHS ON INSULATED CABLE.pdf_第1页
第1页 / 共15页
ANSI ICEA P-45-482-2017 SHORT CIRCUIT PERFORMANCE OF METALLIC SHIELDS AND SHEATHS ON INSULATED CABLE.pdf_第2页
第2页 / 共15页
ANSI ICEA P-45-482-2017 SHORT CIRCUIT PERFORMANCE OF METALLIC SHIELDS AND SHEATHS ON INSULATED CABLE.pdf_第3页
第3页 / 共15页
ANSI ICEA P-45-482-2017 SHORT CIRCUIT PERFORMANCE OF METALLIC SHIELDS AND SHEATHS ON INSULATED CABLE.pdf_第4页
第4页 / 共15页
ANSI ICEA P-45-482-2017 SHORT CIRCUIT PERFORMANCE OF METALLIC SHIELDS AND SHEATHS ON INSULATED CABLE.pdf_第5页
第5页 / 共15页
点击查看更多>>
资源描述

1、ANSI/ICEA P-45-482-2017 Short Circuit Performance of Metallic Shields and Sheaths on Insulated Cable NOTICE AND DISCLAIMER The information in this publication was considered technically sound by the consensus of persons engaged in the development and approval of the document at the time it was devel

2、oped. Consensus does not necessarily mean that there is unanimous agreement among every person participating in the development of this document. The Insulated Cable Engineers Association. Inc. (ICEA) standards and guideline publications, of which the document contained herein is one, are developed

3、through a voluntary consensus standards development process. This process brings together persons who have an interest in the topic covered by this publication. While ICEA administers the process and establishes rules to promote fairness in the development of consensus, it does not independently tes

4、t, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgements contained in its standards and guideline publications. ICEA disclaims liability for personal injury, property, or other damages of any nature whatsoever, whether special, indirect, consequential

5、, or compensatory, directly or indirectly resulting from the publication, use of, application, or reliance on this document. ICEA disclaims and makes no guaranty or warranty, expressed or implied, as to the accuracy or completeness of any information published herein, and disclaims and makes no warr

6、anty that the information in this document will fulfill any of your particular purposes or needs. ICEA does not undertake to guarantee the performance of any individual manufacturer or sellers products or services by virtue of this standard or guide. In publishing and making this document available,

7、 ICEA is not undertaking to render professional or other services for or on behalf of any person or entity, nor is ICEA undertaking to perform any duty owed by any person or entity to someone else. Anyone using this document should rely on his or her own independent judgment or, as appropriate, seek

8、 the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. Information and other standards on the topic covered by this publication may be available from other sources, which the user may wish to consult for additional views or information not

9、covered by this publication. ICEA has no power, nor does it undertake to police or enforce compliance with the contents of this document. ICEA does not certify, test, or inspect products, designs, or installations for safety or health purposes. Any certification or other statement of compliance with

10、 any health or safety-related information in this document shall not be attributable to ICEA and is solely the responsibility of the certifier or maker of the statement. ICEA P-45-482-2017 Page i CONTENTS Page Foreword . ii Section 1 GENERAL 1 1.1 SCOPE . 1 1.2 REFERENCES . 1 Section 2 FORMULAE AND

11、CALCULATIONS . 3 Section 3 Tabulated Parameters . 5 Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 LIST OF TABLES Formulas for Determining Metallic Shield/Sheath Cross-sectional Area . . 4 Parameters for Use in Equations (1 ), (2) or (3) . 5 Values of T1, Approximate Shield or Sheath Operating Temp

12、erature, C at Various Conductor Temperatures 5 Values for Tz, Maximum Allowable Shield or Sheath Transient Temperature, C 6 M Values for Tz Temperature of 200 C . 6 M Values for Tz Temperature of 350 C . 7 Copyright 2017 by the Insulated Cable Engineers Association, Incorporated. ICEA P-45-482-2017

13、Page ii Foreword This publication discusses factors for consideration in approximating the operability of insulated and/or covered wire and cable under the influence of uninterrupted short circuit currents encountered as a result of cable or other equipment faults. The duration of such a fault is co

14、nsidered to be up to approximately 2 seconds. Calculation for single short circuits of longer durations will yield increasingly conservative results. The following items must be considered in order to estimate the short circuit performance of a specific circuit: 1. The magnitude and duration of the

15、fault current including any fault current division due to available conducting paths. 2. The capability of joints, terminations and other accessories in the affected circuit to withstand the thermal and mechanical stresses created by the fault. 3. The interaction between the faulting circuit and sur

16、rounding equipment, such as supports, ties and clamps. 4. The capability of the affected cable circuit, as installed, to withstand the electromagnetic forces created during the fault. 5. The maximum temperature that cable components can withstand without incurring damage due to heating caused by fau

17、lt current flow. 6. Damage to adjacent equipment due to arcing at the site of the fault. 7. For limitations imposed on the short-circuit current in the cable phase conductor see ICEA Publication P-32-382, Short Circuit Characteristics of Insulated Cable. An important simplifying assumption in the fo

18、rmula is the adiabatic nature of the heat generated, i.e., the duration of the fault is so short that all the heat developed by the fault current during this time is assumed to be completely contained within the sheath or shield. The amount of heat dissipated from the sheath or shield during continu

19、ous, single fault occurrences of relatively short duration is small. A significant amount of heat may be dissipated because of the relatively long cooling periods involved for faults interrupted and reestablished with automatic reclosing of circuit protective devices. A non-adiabatic calculation may

20、 be more suitable for these situations and for single. uninterrupted short circuits in excess of 2 seconds requiring close accuracy. Non-adiabatic calculation methods are described in several published works listed in Section 1.2 “References“. The formula (1) described in this publication is based o

21、n the thermal capacity of the metallic sheath/shield material and the transient temperature limit of the adjacent cable component materials. The quantity of heat contained in the metallic sheath/shield is that created by the fault current and is also a function of the temperature rise in the metalli

22、c sheath/shield. The magnitude of the temperature rise is the difference between the upper temperature of the cable material in contact with the sheath/shield and the operating temperature of the sheath/shield immediately prior to the initiation of the fault. The operating temperature of the sheath

23、or shield depends on the temperature of the conductor and the insulation thickness which is determined by the cable voltage rating. See Section 3, Table 3 for suggested estimated values. ICEA P-45-482-2017 Page iii The maximum transient temperature limits of the cable component materials are those w

24、hich cause no significant change in the materials. These limits were extrapolated from laboratory test data. Suggestions for improvements in this publication are welcome, and should be sent to the ICEA website http:/ Copyright 2017 by the Insulated Cable Engineers Association, Incorporated. ICEA P-4

25、5-482-2017 Pageiv 1.1 SCOPE Section 1 GENERAL ICEA P-45-482-2017 Page 1 Equations and parameters have been established for short circuit calculations for sheaths or shields made of aluminum, bronze, copper, lead, steel, zinc and cupronickel alloys. The types of sheaths or shields included are: Wires

26、, applied either helically, as braid or serving; or longitudinally with corrugations. Helically applied flat tape, not overlapped. Helically applied, overlapped, flat tape. Corrugated tape, longitudinally applied. Tubular sheath. The types of cable materials in contact with the sheath or shield are:

27、 crosslinked (thermoset, thermoplastic, impregnated paper, and varnished cloth. The materials which determine the maximum allowable short circuit temperatures are: paper, varnished cloth and several thermoplastic and thermosetting materials presently appearing in ICEA standards. Temperature limits,

28、considered safe, were established for the various coverings and insulation materials. The equations may be used to determine: The maximum short circuit current permitted for a specific sheath/shield and short circuit duration. The sheath/shield size necessary to carry a specific short circuit curren

29、t for a given duration. The maximum duration a specific sheath/shield can carry a specific short circuit current. 1 REFERENCES The following references were reviewed in preparing this document. The Transient Temperature Rise of Round Wire Shields of Extruded Dielectric Cables Under Short Circuit Con

30、ditions, M. A. Martin Jr., A.W. Reczek Jr., IEEE-ICC Open Forum at 57 Meeting Nov. 17-19, 1975. Optimization of Design of Metallic Shield-Concentric Conductors of Extruded Dielectric Cables Under Fault Conditions. EPRI EL-3014, Project 1286-2, final Report 4/83. Optimization of Metallic Shields for

31、Extruded Dielectric Cables Under Fault Conditions, IEEE Paper 86 T or longitudinally with corrugations. 2. Helically applied tape, not overlapped. 1.27 nwb 3. Helically applied flat tape, overlapped. See NOTE 3. 4bd 100 ) m 2100 - L) 4. Corrugated tape, longitudinally applied. 5. Tubular sheath. NOT

32、E 1: Meaning of Symbols: A B b dis dm ds w n L = Effective cross-sectional area of shield or sheath, emil. =Tape overlap, mils (usually 375). = Thickness of tape, mils. = Diameter over extruded insulation screen, mils. = Mean diameter of shield or sheath, mils. = Diameter of wires, mils. =Width of t

33、ape, mils. = Number of serving or braid wires, or tapes. = Overlap of tape, percent. NOTE 2: NOTE 3: The effective area of composite shields is the sum of the effective areas of the components. For example, the effective area of a composite shield consisting of a helically applied tape and a wire se

34、rving would be the sum of the area calculated from Formula 2 (or 3) and Formula 1. The effective area of thin, helically applied overlapped tapes depends, also, upon the degree of electrical contact resistance of the overlaps. Formula 3 may be used to calculate the effective cross-sectional area of

35、the shield for new cable. An increase in contact resistance may occur after cable installation, during service exposed to moisture and heat. Under these conditions the contact resistance may approach infinity, where Formula 2 could apply. Copyright 2017 by the Insulated Cable Engineers Association,

36、Incorporated. Section 3 TABULATED PARAMETERS Table 2 Parameters for Use in Equations (1), (2) or (3) Suggested Values for Properties of ICEA P-45-482-2017 Page 5 K Material Metals at To= 20 C Calculated from SG SH Aluminum* 2.70 0.22 Bronze* 8.80 0.094 Coppert 8.93 0.092 Leadtt 11 .3 0.031 Steel:t:

37、7.85 0.11 Zinc:t:j: 7.14 0.093 Cupronickel Alloys 8.94 0.09 90Cu-10Ni (C70600) 80Cu-20Ni (C71 000) 70Cu-30Ni (C71500) Three quarter hard, 1350 aluminum. * Commercial Bronze, 90% copper, 10% zinc. t Annealed 100% conductivity copper. tt Pure lead (99.99%). :j: Mild or low carbon steel. + Commercial r

38、olled zinc, 0.08% lead. Po “ Equation (2) 2.83 228 0.013 3.95 564 0.030 1.72 234 0.030 20.6 236 0.0011 12.0 180 0.0036 5.91 268 0.0080 1800 19.1 0.019 26.6 0.014 37.5 0.010 These values are believed accurate for the materials shown. Variations may occur due to small changes in composition. Nominal W

39、all Thickness (mils) (See NOTE 2) 220 221-344 345-449 450 Table 3 Values ofT 1, Approximate Shield or Sheath Operating Temperature, oc at Various Conductor Temperatures Shield or Sheath Temperature, C, at Conductor Temperatures (See NOTE 1) 105 oc 100 oc 95C 90 C 85C 80 C 75 C 70 C 65 oc 100 95 90 8

40、5 80 75 70 65 60 95 90 90 85 80 75 70 65 60 95 90 85 80 75 70 65 60 55 N/A N/A N/A 75 70 65 60 55 50 NOTE 1: The maximum conductor temperature should not exceed the normal temperature rating of the insulation used. For more accurate shield/sheath temperatures, contact the cable manufacturer. NOTE 2:

41、 For performance based design wall thicknesses please refer to ICEA S-113-684. Copyright 2017 by the Insulated Cable Engineers Association, Incorporated. ICEA P-45-482-2017 Page 6 Table 4 Values forT 2, Maximum Allowable Shield or Sheath Transient Temperature, C Cable Material in Contact with Shield

42、 or Sheath T 2 Crosslinked (thermoset) 350* High Heat Deformation* 350* Thermoplastic 200 Impregnated Paper 200 Varnished Cloth 200 NOTE: The temperature of the shield or sheath shall be limited by the material in contact with it. For example, a cable having a crosslinked semi-conducting shield unde

43、r the metallic shield and a crosslinked jacket over the metallic shield would have a maximum allowable shield temperature of 350 C. With a thermoplastic jacket it would be 200 C. *For lead sheaths this temperature is limited to 200 C. *See ICEA S-113-684 for definition of High Heat Deformation Table

44、 5 a ues or 2 empera ure o MVI f T T t f 200 C Values for M for the Limiting Conditions Where T 2 = 200 C Shield/Sheath Shield/Sheath Operating Temperature (T1), oc Material 100 95 90 85 80 75 70 65 60 55 50 Aluminum 0.039 0.040 0.041 0.042 0.043 0.044 0.045 0.046 0.047 0.048 0.049 Commercial Bronze

45、 0.043 0.044 0.045 0.046 0.047 0.048 0.049 0.050 0.051 0.052 0.053 Copper 0.058 0.060 0.062 0.063 0.065 0.066 0.068 0.070 0.071 0.073 0.074 Lead 0.011 0.011 0.012 0.012 0.012 0.012 0.013 0.013 0.014 0.014 0.014 Steel 0.022 0.022 0.023 0.024 0.024 0.025 0.026 0.026 0.027 0.027 0.028 Zinc 0.029 0.030

46、0.030 0.031 0.032 0.033 0.034 0.034 0.035 0.036 0.037 c k l upron1c e 90Cu-10Ni (C70600) 0.021 0.021 0.022 0.022 0.023 0.023 0.023 0.024 0.024 0.025 0.025 80Cu-20Ni (C71000) 0.017 0.018 0.018 0.019 0.019 0.020 0.020 0.020 0.021 0.021 0.021 70Cu-30Ni (C71500) 0.015 0.015 0.016 0.016 0.016 0.017 0.017

47、 0.017 0.018 0.018 0.018 Copyright 2017 by the Insulated Cable Engineers Association, Incorporated. Shield/Sheath Material 100 95 Aluminum 0.056 0.057 Commercial Bronze 0.065 0.066 Copper 0.085 0.086 Steel 0.031 0.032 Zinc 0.042 0.043 90Cu-10Ni (C70600) 0.032 0.032 80Cu-20Ni (C71000) 0.027 0.027 70C

48、u-30Ni (C71500) 0.023 0.023 Table 6 a ues or 2 empera ure o MVI f TT t f 350 C ICEA P-45-482-2017 Page 7 Values for M for the Limiting Conditions W here T 2 = 350 C Shield/Sheath Operating Temperature (T1), oc 90 85 80 75 70 65 60 55 50 0.058 0.059 0.060 0.060 0.061 0.062 0.063 0.063 0.064 0.066 0.0

49、67 0.068 0.068 0.069 0.070 0.070 0.071 0.072 0.088 0.089 0.090 0.091 0.092 0.093 0.094 0.096 0.097 0.032 0.033 0.033 0.034 0.034 0.035 0.035 0.036 0.036 0.044 0.044 0.045 0.045 0.046 0.046 0.047 0.047 0.048 c kl upron1c e 0.033 0.033 0.033 0.034 0.034 0.034 0.034 0.035 0.035 0.028 0.028 0.028 0.028 0.029 0.029 0.029 0.030 0.030 0.024 0.024 0.024 0.024 0.025 0.025 0.025 0.025 0.026 Copyright 2017 by the Insulated Cable Engineers Association, Incorporated.

展开阅读全文
相关资源
  • ANSI Z97 1-2009 American National Standard for Safety Glazing Materials used in Buildings - Safety Performance Specifications and Methods of Test《建筑物中窗用玻璃材料安全性用.pdfANSI Z97 1-2009 American National Standard for Safety Glazing Materials used in Buildings - Safety Performance Specifications and Methods of Test《建筑物中窗用玻璃材料安全性用.pdf
  • ANSI Z97 1 ERTA-2010 Re ANSI Z97 1 - 2009 Errata《修订版 美国国家标准学会Z97 1-2009标准的勘误表》.pdfANSI Z97 1 ERTA-2010 Re ANSI Z97 1 - 2009 Errata《修订版 美国国家标准学会Z97 1-2009标准的勘误表》.pdf
  • ANSI Z21 40 2a-1997 Gas-Fired Work Activated Air-Conditioning and Heat Pump Appliances (Same as CGA 2 92a)《燃气、工作激活空气调节和热泵器具(同 CGA 2 92a)》.pdfANSI Z21 40 2a-1997 Gas-Fired Work Activated Air-Conditioning and Heat Pump Appliances (Same as CGA 2 92a)《燃气、工作激活空气调节和热泵器具(同 CGA 2 92a)》.pdf
  • ANSI Z124 9-2004 American National Standard for Plastic Urinal Fixtures《塑料小便器用美国国家标准》.pdfANSI Z124 9-2004 American National Standard for Plastic Urinal Fixtures《塑料小便器用美国国家标准》.pdf
  • ANSI Z124 4-2006 American National Standard for Plastic Water Closet Bowls and Tanks《塑料抽水马桶和水箱用美国国家标准》.pdfANSI Z124 4-2006 American National Standard for Plastic Water Closet Bowls and Tanks《塑料抽水马桶和水箱用美国国家标准》.pdf
  • ANSI Z124 3-2005 American National Standard for Plastic Lavatories《塑料洗脸盆用美国国家标准》.pdfANSI Z124 3-2005 American National Standard for Plastic Lavatories《塑料洗脸盆用美国国家标准》.pdf
  • ANSI T1 659-1996 Telecommunications - Mobility Management Application Protocol (MMAP) RCF-RACF Operations《电信 可移动管理应用协议(MMAP) RCF-RACF操作》.pdfANSI T1 659-1996 Telecommunications - Mobility Management Application Protocol (MMAP) RCF-RACF Operations《电信 可移动管理应用协议(MMAP) RCF-RACF操作》.pdf
  • ANSI T1 651-1996 Telecommunications – Mobility Management Application Protocol (MMAP)《电信 可移动性管理应用协议》.pdfANSI T1 651-1996 Telecommunications – Mobility Management Application Protocol (MMAP)《电信 可移动性管理应用协议》.pdf
  • ANSI T1 609-1999 Interworking between the ISDN User-Network Interface Protocol and the Signalling System Number 7 ISDN User Part《电信 ISDN用户间网络接口协议和7号信令系统ISDN用户部分.pdfANSI T1 609-1999 Interworking between the ISDN User-Network Interface Protocol and the Signalling System Number 7 ISDN User Part《电信 ISDN用户间网络接口协议和7号信令系统ISDN用户部分.pdf
  • ANSI T1 605-1991 Integrated Services Digital Network (ISDN) - Basic Access Interface for S and T Reference Points (Layer 1 Specification)《综合服务数字网络(ISDN) S和T基准点的.pdfANSI T1 605-1991 Integrated Services Digital Network (ISDN) - Basic Access Interface for S and T Reference Points (Layer 1 Specification)《综合服务数字网络(ISDN) S和T基准点的.pdf
  • 猜你喜欢
    相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > ANSI

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1