1、NEMA Standards PublicationNational Electrical Manufacturers AssociationANSI/NEMA C136.29-2011Roadway and Area Lighting Equipment Metal Halide Lamps Guide for SelectionANSI C136.29-2011 Page iii ANSI/NEMA C136.29-2011 American National Standard Roadway and Area Lighting Equipment Metal Halide Lamps G
2、uide for Selection Secretariat: National Electrical Manufacturers Association Approved January 31, 2012 American National Standards Institute, Inc. C136.29-2011 Page iv v13 2 2 4 NOTICE AND DISCLAIMER The information in this publication was considered technically sound by the consensus of persons en
3、gaged in the development and approval of the document at the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person participating in the development of this document. ANSI standards and guideline publications, of which the document contained h
4、erein is one, are developed through a voluntary consensus standards development process. This process brings together volunteers and/or seeks out the views of persons who have an interest in the topic covered by this publication. While NEMA administers the process to promote fairness in the developm
5、ent of consensus, it does not write the document and it does not independently test, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgments contained in its standards and guideline publications. NEMA disclaims liability for any personal injury, property
6、, or other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, application, or reliance on this document. NEMA disclaims and makes no guaranty or warranty, express or implied, as to the accuracy o
7、r completeness of any information published herein, and disclaims and makes no warranty that the information in this document will fulfill any of your particular purposes or needs. NEMA does not undertake to guarantee the performance of any individual manufacturer or sellers products or services by
8、virtue of this standard or guide. In publishing and making this document available, NEMA is not undertaking to render professional or other services for or on behalf of any person or entity, nor is NEMA undertaking to perform any duty owed by any person or entity to someone else. Anyone using this d
9、ocument should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. Information and other standards on the topic covered by this publication may be available from other s
10、ources, which the user may wish to consult for additional views or information not covered by this publication. NEMA has no power, nor does it undertake to police or enforce compliance with the contents of this document. NEMA does not certify, test, or inspect products, designs, or installations for
11、 safety or health purposes. Any certification or other statement of compliance with any health or safetyrelated information in this document shall not be attributable to NEMA and is solely the responsibility of the certifier or maker of the statement. C136.29-2011 Page v 3 5 Published by: National E
12、lectrical Manufacturers Association 1300 North 17th Street, Rosslyn, VA 22209 g164 Copyright 2011 by National Electrical Manufacturers Association All rights reserved including translation into other languages, reserved under the Universal Copyright Convention, the Berne Convention for the Protectio
13、n of Literary and Artistic Works, and the International and Pan American Copyright Conventions. No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher. Printed in the United States of America. A
14、MERICAN NATIONAL STANDARD Approval of an American National Standard requires verification by ANSI that the requirements for due process, consensus, and other criteria for approval have been met by the standards developer. Consensus is established when, in the judgment of the ANSI Board of Standards
15、Review, substantial agreement has been reached by directly and materially affected interests. Substantial agreement means much more than a simple majority, but not necessarily unanimity. Consensus requires that all views and objections be considered, and that a concerted effort be made toward their
16、resolution. The use of American National Standards is completely voluntary; their existence does not in any respect preclude anyone, whether he has approved the standards or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standards. T
17、he American National Standards Institute does not develop standards and will in no circumstances give an interpretation of any American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an American National Standard in the name of the American Nat
18、ional Standards Institute. Requests for interpretations should be addressed to the secretariat or sponsor whose name appears on the title page of this standard. This American National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute requir
19、e that action be taken periodically to reaffirm, revise, or withdraw this standard. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute. C136.29-2011 Page iv v15 2 2 4 C136.29-2011 Page v 3 5 CONTE
20、NTS 1 Scope 1 2 Normative References 1 3 General Description and Information 1 Table 1 Probe Start Metal halide Lamps . 2 Table 2 Ceramic Metal Halide Pulse Start Lamps 2 Table 3 Pulse Start Metal Halide Lamps . 3 C136.29-2011 Page 1 1 Scope This selection guide includes screw base single ended meta
21、l halide lamps that can be used in roadway and area lighting equipment 2 Normative References This standard incorporates by undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed below. For un
22、dated references, the latest edition of the publication referred to applies (including amendments). ANSI C78.43, American National Standard for Single-Ended Metal Halide Lamps. ANSI C81.61, American National Standard for Electrical Lamp Bases. ANSI C82.4, American National Standard for Ballasts for
23、High-Intensity Discharge and Low-Pressure Sodium Lamps. 3 General Description and Information Metal Halide lamps may be operated on either series or multiple circuits with the use of the proper ballast. Lamps listed in the following tables conform to the applicable parts of ANSI C78.43, ANSI C81.61,
24、 and ANSI C82.4. The ANSI lamp code should match the ANSI ballast code to ensure proper luminaire operation. The below tables contains typical data that varies by lamp manufacturer. It is suggested that the user refer to current lamp manufacturer catalogs for current data such as average lamp life a
25、nd lumen ratings. Lamp bases constructed of brass or corrosion resistant alloy are recommended. Consult the manufacturer for availability. This selection guide contains data for lamps with a clear outer glass jacket (no phosphorous coating). Coated lamps are available in most wattages and typically
26、have a slightly higher color rendering index (CRI) and a slightly lower lumen output than clear jacket lamps. Consult the manufacturer for availability. Some lamps are only available for a specific operating (burning) position (vertical base up, vertical base down, horizontal). Many metal halide lam
27、ps are designed to operate in any burning. These are known as universal lamps. Universal lamps generally have slightly lower lumen output and average life but can be used in any burning position. C136.29-2011 Page 2 3 5 Table 1 Probe Start Metal Halide Lamps All of the below listed single ended lamp
28、s have a clear finish, screw base, typical correlated color temperature (CCT) of 4000K, and a typical color rendering index (CRI) of 65. Watts Bulb Base ANSI Code Initial Lumens Rated Average Life (hrs) MOL mm (in.) LCL mm (in.) 175 ED17 E26 MED M57 14000 10500 138 (5.44) 86 (3.4) 175 ED28 E39 MOG M
29、57 13500 10000 211 (8.31) 127 (5.0) 250 ET18 E39 MOG M58 22000 10000 248 (9.75) 146 (5.75) 250 ED28 E39 MOG M58 21000 13700 211 (8.31) 127 (5.0) 400 ET18 E39 MOG M59 36000 20000 248 (9.75) 156 (6.14) 400 ED28 E39 MOG M59 34000 20000 211 (8.31) 127 (5.0) 400 ED37 E39 MOG M59 34000 20000 292 (11.50) 1
30、78 (7.0) 1000 BT37 E39 MOG M47 105000 12000 292 (11.50) 178 (7.0) 1000 BT56 E39 MOG M47 105000 12000 391 (15.38) 241 (9.5) 1500 BT56 E39 MOG M47 161000 3000 391 (15.38) 241 (9.5) MOL = Maximum Outer Length LCL = Light Center Length Table 2 Ceramic Metal Halide Pulse Start Lamps All of the below list
31、ed single ended lamps have a clear finish, screw base, typical correlated color temperature (CCT) of 4000K, and a typical color rendering index (CRI) of 90. MOL = Maximum Outer Length LCL = Light Center Length Table 3 Pulse Start Metal Halide Lamps Watts Bulb Base ANSI Code Initial Lumens Rated Aver
32、age Life (hrs) MOL mm (in.) LCL mm (in.) 50 ED17 E26 MED M148/M110 4100 12000 138 (5.44) 86 (3.4) 70 ED17 E26 MED M143/M98 6000 12000 138 (5.44) 86 (3.4) 100 ED17 E26 MED M140/M90 7500 20000 138 (5.44) 86 (3.4) 150 ED17 E26 MED M142/M102 13000 12000 138 (5.44) 86 (3.4) 250 BT28 E39 MOG M153 23000 20
33、000 211 (8.31) 127 (5.0) 320 BT37 E39 MOG M170/M132 31000 20000 292 (11.50) 178 (7.0) 350 BT37 E39 MOG M171/M131 33000 20000 292 (11.50) 178 (7.0) 400 BT37 E39 MOG M172/M154 36000 20000 292 (11.50) 178 (7.0) C136.29-2011 Page 3 v3 2 2 4 All of the below listed single ended lamps have a clear finish,
34、 screw base, typical correlated color temperature (CCT) of 4000K, and a typical color rendering index (CRI) of 65. Watts Bulb Base ANSI Code Initial Lumens Rated Average Life (hrs) MOL mm (in.) LCL mm (in.) 50 ED17 E26 MED M110 3400 10000 138 (5.44) 86 (3.4) 70 ED17 E26 MED M98 5600 15000 138 (5.44)
35、 86 (3.4) 70 ED28 E39 MOG M98 5600 15000 211 (8.31) 127 (5.0) 100 ED17 E26 MED M90 9000 15000 138 (5.44) 86 (3.4) 100 ED28 E39 MOG M90 9000 15000 211 (8.31) 127 (5.0) 125 ED17 E26 MED M150 12000 15000 138 (5.44) 86 (3.4) 125 ED28 E39 MOG M150 12000 15000 211 (8.31) 127 (5.0) 150 ED17 E26 MED M102 14
36、000 15000 138 (5.44) 86 (3.4) 150 ED28 E39 MOG M102 14000 15000 211 (8.31) 127 (5.0) 175 ED17 E26 MED M152 17500 15000 138 (5.44) 86 (3.4) 175 ED28 E39 MOG M152 17500 15000 211 (8.31) 127 (5.0) 200 ED17 E39 MOG M136 21000 12000 138 (5.44) 86 (3.4) 200 ED28 E39 MOG M136 21000 15000 211 (8.31) 127 (5.
37、0) 200 T15 E39 MOG M136 19000 15000 211 (8.31) 127 (5.0) 250 ED28 E39 MOG M153 25000 15000 211 (8.31) 127 (5.0) 250 T15 E39 MOG M153 22000 15000 211 (8.31) 127 (5.0) 320 ED28 E39 MOG M154 33000 20000 211 (8.31) 127 (5.0) 320 ED37 E39 MOG M154 33000 20000 292 (11.50) 178 (7.0) 320 T15 E39 MOG M154 30
38、000 20000 292 (11.50) 178 (7.0) 320 T15 E39 MOG M154 30000 20000 248 (9.75) 146 (5.75) 350 ED28 E39 MOG M131 37000 20000 211 (8.31) 127 (5.0) 350 T15 E39 MOG M131 37000 20000 211 (8.31) 127 (5.0) 350 ED37 E39 MOG M131 37000 20000 292 (11.50) 178 (7.0) 350 T15 E39 MOG M131 37000 20000 292 (11.50) 178
39、 (7.0) 400 ED28 E39 MOG M155 44000 20000 211 (8.31) 127 (5.0) 400 ED37 E39 MOG M155 44000 20000 292 (11.50) 178 (7.0) 450 ED37 E39 MOG M144 50000 20000 292 (11.50) 178 (7.0) 575 BT37 E39 MOG M178 60000 20000 292 (11.50) 178 (7.0) 750 BT37 E39 MOG M149 78000 16000 292 (11.50) 178 (7.0) 875 BT37 E39 M
40、OG M166 95000 20000 292 (11.50) 178 (7.0) 1000 BT37 E39 MOG M141 115000 12000 292 (11.50) 178 (7.0) MOL = Maximum Outer Length LCL = Light Center Length C136.29-2011 Page 4 NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION 1300 NORTH 17TH STREET, SUITE 900 ROSSLYN. VA 22209www.NEMA.orgTO ORDER ADDITIONAL NEMA STANDARDS VISITWWW.GLOBAL.IHS.COM OR CALL 1-800-854-7179/1-303-397-79565612_0514TB
