ANSI UL 1315-1995 UL Standard for Safety Metal Waste Paper Containers (First Edition Reprint with Revisions Through and Including September 11 2012).pdf

上传人:medalangle361 文档编号:438858 上传时间:2018-11-14 格式:PDF 页数:14 大小:565.38KB
下载 相关 举报
ANSI UL 1315-1995 UL Standard for Safety Metal Waste Paper Containers (First Edition Reprint with Revisions Through and Including September 11 2012).pdf_第1页
第1页 / 共14页
ANSI UL 1315-1995 UL Standard for Safety Metal Waste Paper Containers (First Edition Reprint with Revisions Through and Including September 11 2012).pdf_第2页
第2页 / 共14页
ANSI UL 1315-1995 UL Standard for Safety Metal Waste Paper Containers (First Edition Reprint with Revisions Through and Including September 11 2012).pdf_第3页
第3页 / 共14页
ANSI UL 1315-1995 UL Standard for Safety Metal Waste Paper Containers (First Edition Reprint with Revisions Through and Including September 11 2012).pdf_第4页
第4页 / 共14页
ANSI UL 1315-1995 UL Standard for Safety Metal Waste Paper Containers (First Edition Reprint with Revisions Through and Including September 11 2012).pdf_第5页
第5页 / 共14页
亲,该文档总共14页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 1315 Metal Waste Paper ContainersUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER

2、REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Metal Waste Paper Containers, UL 1315 First Edition, Dated November 27, 1995 Summary of Topics This revision to ANSI/UL 1315 is being issued to reect the recent reaffirmation of UL 1315 as an American National Standar

3、d. Text that has been changed in any manner or impacted by ULs electronic publishing system is marked with a vertical line in the margin. Changes in requirements are marked with a vertical line in the margin and are followed by an effective date note indicating the date of publication or the date on

4、 which the changed requirement becomes effective. The revised requirements are substantially in accordance with Proposal(s) on this subject dated July 20, 2012. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means,

5、electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will U

6、L be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possib

7、ility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, li

8、ability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections,

9、tables, gures, and/or other elements of the Standard having future effective dates as indicated in the note following the affected item. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUI

10、REMENTS notice. SEPTEMBER 11, 2012 UL 1315 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL SEPTEMBER 11, 2012 UL 1315 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSI

11、ON FROM UL NOVEMBER 27, 1995 (Title Page Reprinted: September 11, 2012) 1 UL 1315 Standard for Metal Waste Paper Containers First Edition November 27, 1995 This ANSI/UL Standard for Safety consists of the First Edition including revisions through September 11, 2012. The most recent designation of AN

12、SI/UL 1315 as a Reaffirmed American National Standard (ANS) occurred on September 11, 2012. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revisions on any part of the Standard may be submitted to

13、UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and

14、all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2012 UNDERWRITERS LABORATORIES INC. ANSI/UL 1315-2003 (R2012)UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL DECEM

15、BER 21, 2007 METAL WASTE PAPER CONTAINERS - UL 1315 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .5 2 General 5 2.1 Units of measurement .5 2.2 Components .5 2.3 Undated references .6 CO

16、NSTRUCTION 3 General 6 4 Materials .6 PERFORMANCE 5 Tip-Over Test .6 6 Operation Test 6 7 Drop Test 7 8 Fire Test .7 MARKING 9 General 8 SUPPLEMENT SA - OPEN-TOP METALLIC CONTAINERS FOR WASTE PAPER INTRODUCTION SA1 Scope SA1 PERFORMANCE SA2 Drop Test .SA1 SA3 Internal Fire Test SA1 DECEMBER 21, 2007

17、 METAL WASTE PAPER CONTAINERS - UL 1315 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL This page intentionally left blank. DECEMBER 21, 2007 METAL WASTE PAPER CONTAINERS - UL 1315 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODU

18、CTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These requirements cover metal receptacles intended primarily for temporary, indoor storage of waste paper and other similar materials. These containers are intended to be emptied regularly and their contents disposed of. 1.2

19、These requirements cover waste paper containers intended for use as complete assemblies, consisting of a container body and a head or cover. They may be provided with metal or nonmetallic internal liners. They are designed to: a) Limit the external surface temperatures of the container bottom should

20、 their contents become ignited; b) Extinguish the re; and c) Contain the contents without contributing fuel to the re. 1.3 A product that contains features, characteristics, components, materials, or systems new or different from those covered by the requirements in this standard, and that involves

21、a risk of re, electric shock, or injury to persons shall be evaluated using the appropriate additional component and end-product requirements as determined necessary to maintain the acceptable level of safety as originally anticipated by the intent of this standard. A product whose features, charact

22、eristics, components, materials, or systems conict with specic requirements or provisions of this standard cannot be judged to comply with this standard. Where considered appropriate, revision of requirements shall be proposed and adopted in conformance with the methods employed for development, rev

23、ision, and implementation of this standard. 2 General 2.1 Units of measurement 2.1.1 If a value for measurement is followed by a value in other units in parentheses, the second value may be only approximate. The rst stated value is the requirement. 2.2 Components 2.2.1 Except as indicated in 2.2.2,

24、a component of a product covered by this standard shall comply with the requirements for that component. 2.2.2 A component need not comply with a specic requirement that: a) Involves a feature or characteristic not needed in the application of the component in the value covered by this standard, or

25、b) Is superseded by a requirement in this standard. 2.2.3 A component shall be used in accordance with its recognized rating established for the intended conditions of use. NOVEMBER 27, 1995 METAL WASTE PAPER CONTAINERS - UL 1315 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DI

26、STRIBUTION WITHOUT PERMISSION FROM UL 2.2.4 Specic components are recognized as being incomplete in construction features or restricted in performance capabilities. Such components are intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and shal

27、l be used only under those specic conditions for which they have been recognized. 2.3 Undated references 2.3.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. CONSTRUCTION 3 G

28、eneral 3.1 Vertical seams and bottom joints of the container or of metal liners, if provided, shall be locked-seamed or welded. 3.2 The head or cover shall be provided with means for retaining it in place when assembled on the container body or may be of the type consisting of a one piece container

29、body/head assembly that ts over an internal liner. 3.3 The means of retaining the head or cover to the container body may be an indented or beaded construction providing a snap type t between the parts or it may be permanently attached by means of a hinge or the equivalent. 4 Materials 4.1 The conta

30、iner body and the head or cover shall be made of sheet steel or of corrosion resistant metal as described in 4.2. 4.2 The container body and the outside surface of the head or cover shall be either painted or hot-dipped galvanized unless made of corrosion resistant metal. PERFORMANCE 5 Tip-Over Test

31、 5.1 The test is to be conducted on all containers which do not have a permanently attached head or cover, that is hinged, are not of the type consisting of a one piece container body/head assembly, and do not have handles on the sides of the container body. 5.2 The container shall be able to be lif

32、ted by the head or cover after being tested as specied in 5.3. 5.3 One container of each type is to be tipped over ve times, at least once on each side if at sided or evenly distributed around the circumference if round. 6 Operation Test 6.1 Containers provided with a self-closing lid are to be subj

33、ected to 6,000 cycles of operation. The lid shall not become inoperative to the extent that it will affect the results of the re test. 6.1 effective May 27, 1997 NOVEMBER 27, 1995 METAL WASTE PAPER CONTAINERS - UL 1315 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION

34、WITHOUT PERMISSION FROM UL 7 Drop Test 7.1 Containers having less than 30 gallons (112.7 liters) of capacity, or all internal liners, if provided, are to be tested as specied in 7.3, prior to the re test. 7.2 Containers having less than 30 gallons (112.7 liters) of capacity, and all internal liners,

35、 if provided, shall not rupture, break apart or be damaged to the extent that it will affect the results of the Fire Test, Section 8, after being tested as specied in 7.3. 7.3 Each test sample to be subjected to the re test is to be dropped ve times from a height of 5 feet (1.52 m) onto a concrete o

36、or, so as to strike once on the bottom, the top, the side, a top corner and a bottom corner. The tests are to be conducted on samples of the liner and on samples of the container with the liner in place. 8 Fire Test 8.1 Samples of each size container, with the head or cover and liner, if provided, i

37、n place is to be subjected to 8.2 8.7. 8.2 Each container is to be placed on a 3/4 inch (19.1 mm) thick painted (black) plywood sheet, freestanding in a draft free room and away from any walls or other obstructions. Three thermocouples are to be placed on the surface of the plywood under the contain

38、er on a line representing the diameter or centerline of the container body. One thermocouple is to be placed in the center of the container and the other two are to be placed along the centerline of the container at 1/6 of the distance from each edge. 8.2 revised July 14, 1999 8.3 Separate tests are

39、 to be conducted with each container lled 1/3 full, 2/3 full, and completely full of shredded, uffed newspaper, which is to be ignited by a match. The width of the strips of newspaper shall be 0.20 0.10 inch. The shredded paper, when in place in the container, is to have a bulk density of 5.1 oz/ft

40、3 (5.16 kg/m 3 ). If the container is equipped with a lid that is not of the self-closing type, the re test is to be conducted with the lid open. 8.3 revised July 14, 1999 8.4 The tests shall indicate that the container assembly effectively contains the contents, reduces the duration and intensity o

41、f combustion and shall extinguish the re in accordance with 8.5 8.7. 8.5 The maximum temperature attained on the plywood during the tests on the container assembly shall not exceed the test ambient temperature by more than 79C (175F). 8.6 The tests are to be conducted at any ambient temperature with

42、in the range of 10 40C (50 104F). 8.7 The container assembly shall extinguish the re within 20 minutes of ignition and at least 25 percent by weight of unburned paper shall remain. JULY 14, 1999 METAL WASTE PAPER CONTAINERS - UL 1315 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION O

43、R DISTRIBUTION WITHOUT PERMISSION FROM UL MARKING 9 General 9.1 A product shall be legibly and permanently marked with: a) The manufacturers name, trade name, or trademark or other descriptive marking by which the organization responsible for the product may be identied; b) A distinctive ( catalog o

44、r model ) number or the equivalent; c) The date or other dating period of manufacture not exceeding any three consecutive months. Exception No. 1: The manufacturers identication may be in a traceable code if the product is identied by the brand or trademark owned by a private labeler. Exception No.

45、2: The date of manufacture may be abbreviated; or may be in a nationally accepted conventional code or in a code afrmed by the manufacturer, provided that the code: a) Does not repeat in less than 10 years for a household product and less than 20 years for a commercial product, and b) Does not requi

46、re reference to the production records of the manufacturer to determine when the product was manufactured. Revised 9.1 effective January 14, 2000 9.2 Each head or cover and each container shall be marked with the statement, Head No. _ For Use With Container No. _; or equivalent and Container No. _ F

47、or Use With Head No. _; or equivalent, as appropriate. 9.3 A container that is to be used in conjunction with a liner shall be marked with the statement, Container No._ For Use With Liner No. _; or a combination of this statement and the container statement from 9.2. 9.4 All markings shall be legibl

48、e and permanent. Markings shall be provided by stamping, by a metal nameplate, by stenciling or painting, or equivalent. 9.5 If a manufacturer produces waste paper containers at more than one factory, each individual waste paper container shall have a distinctive marking to identify it as the produc

49、t of a particular factory. JULY 14, 1999 METAL WASTE PAPER CONTAINERS - UL 1315 8UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL SUPPLEMENT SA - OPEN-TOP METALLIC CONTAINERS FOR WASTE PAPER INTRODUCTION SA1 Scope SA1.1 These requirements apply to open-top metallic containers for waste paper. These requirements add to the applicable requirements in the body of the standard. PERFORMANCE SA2 Drop T

展开阅读全文
相关资源
  • ANSI Z97 1-2009 American National Standard for Safety Glazing Materials used in Buildings - Safety Performance Specifications and Methods of Test《建筑物中窗用玻璃材料安全性用.pdfANSI Z97 1-2009 American National Standard for Safety Glazing Materials used in Buildings - Safety Performance Specifications and Methods of Test《建筑物中窗用玻璃材料安全性用.pdf
  • ANSI Z97 1 ERTA-2010 Re ANSI Z97 1 - 2009 Errata《修订版 美国国家标准学会Z97 1-2009标准的勘误表》.pdfANSI Z97 1 ERTA-2010 Re ANSI Z97 1 - 2009 Errata《修订版 美国国家标准学会Z97 1-2009标准的勘误表》.pdf
  • ANSI Z21 40 2a-1997 Gas-Fired Work Activated Air-Conditioning and Heat Pump Appliances (Same as CGA 2 92a)《燃气、工作激活空气调节和热泵器具(同 CGA 2 92a)》.pdfANSI Z21 40 2a-1997 Gas-Fired Work Activated Air-Conditioning and Heat Pump Appliances (Same as CGA 2 92a)《燃气、工作激活空气调节和热泵器具(同 CGA 2 92a)》.pdf
  • ANSI Z124 9-2004 American National Standard for Plastic Urinal Fixtures《塑料小便器用美国国家标准》.pdfANSI Z124 9-2004 American National Standard for Plastic Urinal Fixtures《塑料小便器用美国国家标准》.pdf
  • ANSI Z124 4-2006 American National Standard for Plastic Water Closet Bowls and Tanks《塑料抽水马桶和水箱用美国国家标准》.pdfANSI Z124 4-2006 American National Standard for Plastic Water Closet Bowls and Tanks《塑料抽水马桶和水箱用美国国家标准》.pdf
  • ANSI Z124 3-2005 American National Standard for Plastic Lavatories《塑料洗脸盆用美国国家标准》.pdfANSI Z124 3-2005 American National Standard for Plastic Lavatories《塑料洗脸盆用美国国家标准》.pdf
  • ANSI T1 659-1996 Telecommunications - Mobility Management Application Protocol (MMAP) RCF-RACF Operations《电信 可移动管理应用协议(MMAP) RCF-RACF操作》.pdfANSI T1 659-1996 Telecommunications - Mobility Management Application Protocol (MMAP) RCF-RACF Operations《电信 可移动管理应用协议(MMAP) RCF-RACF操作》.pdf
  • ANSI T1 651-1996 Telecommunications – Mobility Management Application Protocol (MMAP)《电信 可移动性管理应用协议》.pdfANSI T1 651-1996 Telecommunications – Mobility Management Application Protocol (MMAP)《电信 可移动性管理应用协议》.pdf
  • ANSI T1 609-1999 Interworking between the ISDN User-Network Interface Protocol and the Signalling System Number 7 ISDN User Part《电信 ISDN用户间网络接口协议和7号信令系统ISDN用户部分.pdfANSI T1 609-1999 Interworking between the ISDN User-Network Interface Protocol and the Signalling System Number 7 ISDN User Part《电信 ISDN用户间网络接口协议和7号信令系统ISDN用户部分.pdf
  • ANSI T1 605-1991 Integrated Services Digital Network (ISDN) - Basic Access Interface for S and T Reference Points (Layer 1 Specification)《综合服务数字网络(ISDN) S和T基准点的.pdfANSI T1 605-1991 Integrated Services Digital Network (ISDN) - Basic Access Interface for S and T Reference Points (Layer 1 Specification)《综合服务数字网络(ISDN) S和T基准点的.pdf
  • 猜你喜欢
    相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > ANSI

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1