1、MIL-C-70630 (5) D 9999906 20115282 696 I INCH-POUND I MILITARY MIL-C-70630 (AR) AMENDMENT 5 31 October 1995 SUPERSEDING AMENDMENT 4 1 June 1992 SPECIFICATION CONTAINER, AMMUNITION, METAL, PA117 FOR CARTRIDGE 105MM TANK AMMUNITION This amendment forms a part of Military Specification MIL-C-70630 (AR)
2、, dated 23 September 1987, and is approved for use by the U.S. Army Armament Research, Development and Engineering Center and is available for use by all Departments and Agencies of the Department of Defense. PAGE 2 * Under Standards, Military, delete: lvMIL-STD-105 - Sampling Procedures and Tables
3、for Inspection by Attributes.“ PAGE 3 2.2, add: IIAMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) * ANSI/ASQCZ1.4 - Sampling Procedures and Tables for Inspection by Attributes.“ 3.3.1: Delete drawing 1193781771t and substitute ll9386828-3ll. PAGE 6 First article inspection, Examination or Test: Cover A
4、ssemblv: Delete: “(Dwg. 9378170)l and substitute (DWg. 9386824-2) l. Body: Delete: Ii(Dwg. 9378177)“ and substitute (DWg. 9386828-3) II. PAGE 7 First article inspection, Examination or Test: Gasket: Delete: II(Dwg. 9378178)“ and substitute II (Dwg. 12910349-3) I. AMSC N/A 1 of 6 FSC 8140 DISTRIBUTIO
5、N STATEMENT A. Approved for public release; distribution is unlimited. Licensed by Information Handling ServicesMIL-C-70630 (AR) AMENDMENT 5 PAGE 8 * 4.4.2, delete flMIL-STD-10511 and substitute flANSI/ASQCZ1.4ii. PAGE 10 4.4.2.2: Major defect 101: Under AQL or loo%, delete 110.40%11. Under No. of S
6、ample Units, add ii5(a)11. Minor defect 201: Delete in its entirety. Under Notes, add the following: !(a) 5 samples per lot in conjunction with Suppliers Material Certification.1f PAGE 11 4.4.2.3: Next Higher Assembly: Delete “9378170“ and substitute “9386824-2“. PAGE 12 4.4.2.4: Delete drawing numb
7、er 119378179“ and substitute 119344037-2“. Delete major defect 106: “106 True position of small diameter (two places) C.40% 3.2 Gage“ . Next Higher Assembly: Delete 11937817011 and substitute “9386824-2“. PAGE 13 4.4.2.5: Next Higher Assembly: Delete 1193781701r and substitute “9386824-2“. PAGE 14 4
8、.4.2.6: Next Higher Assembly: Delete “9378170“ and substitute “9386824-2“. 2 Licensed by Information Handling ServicesMIL-C-70630 (AR) AMENDMENT 5 PAGE 15 4.4.2.7: Delete drawing number 11937818211 and substitute “9386821-211. Next Higher Assembly: Delete “9378181“ and substitute 9386822-2“. Major d
9、efect 101: Under AQL or loo%, delete 110.40%11. Major defect 101: Under No. of Sample Units, add f15(a)11. Under Notes, add the following: “(a) 5 samples per lot in conjunction with Suppliers Material Certification. II PAGE 16 4i4.2.8: Delete in its entirety and substitute new 4.4.2.8 included. 3 Li
10、censed by Information Handling Serviceswi ZI n a: 4 O M Lo O pc I u I LI H 5: d c t t i : t 1 a Y 1 C c 4 4 s Y 4 c flIL-C-70b30 (5 1 9999906 2015285 3T5 Xj N =l. =a- - o b =I- NNCuNNN . t- MMMMMM o M .o o. O000 O m a .FI c rn I= m k 24 L L O O a ti O Q) o c Q) 73 .d W Licensed by Information Handli
11、ng Services MIL-C-70630 (5 1 9999906 2035286 231 U MIL-C-70630 (AR) AMENDMENT 5 PAGE 17 4.4.2.9: Next Higher Assembly: Delete 11937817011 and substitute “9386824-2“. Delete drawing number 1937818211 and substitute “9386822-2“. PAGE 18 4.4.2.10: Drawing Number: Delete lI937817Ofl and substitute 11938
12、6824-2*1. Major defect 102: Delete in its entirety. PAGE 19 4.4.2.11: Major defect 103: Delete llInsidell and substitute “Outsiden1. Delete drawing number 11937817511 and substitute “9386827-2“. PAGE 20 4.4.2.12: Major defect 103: Delete lpnsidelf and substitute “Outside“. Delete minor defect 201: “
13、201 True position of interlocking cutouts 0.65% 3.2 Gage“. Delete drawing number 119378173“ and substitute “9386826-2“ e PAGE 21 4.4.2.13: Drawing Number: Delete “9378177“ and substitute “9386828-2“ e Major defect 103: Under Examination or Test column, delete “Perpendicularity of ends“ and substitut
14、e “Flatness of body endV1 . 5 Licensed by Information Handling ServicesMIL-C-70630 (AR) AMENDMENT 5 PAGE 22 4.4.2.14: Drawing Number: Delete “9344045“ and substitute “9386837“. PAGE 23 4.4.2.15: Delete: “108 Flatness of .I in its entirety. Major defect 104: Delete in its entirety. PAGE 24 4.4.2.16:
15、Major defect 101: Delete in its entirety. PAGE 29 * 4.4.2.21, Note (b): Add: Ir (applicable to container supplier only) . I PAGE 30 4.4.2.22: Delete this paragraph in its entirety. NOTE: The margins of this amendment are marked with an asterisk or vertical lines to indicate where changes (additions,
16、 modifications, corrections, deletions) from the previous amendment were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations: Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. Custodian: Army - AR Preparing activity: Army - AR (Project 8140-0080) 6 Licensed by Information Handling Services
