1、MIL-I-4Ob (4) 13 m 777770b 043i67 7 MIL-1-48086 (AR) AMENDMENT 4 29 June 1990 SUPERSEDING AMENDMENT 3 18 March 1982 _I MILITARY SPECIFICATION INCREMENTS, PROPELLANT FOR THARGE, PROPELLING, M36A2 (MADE FROM PROPELLANT M8) This Amendment forms a part of Military Specification MIL-1-48086 (MU) dated 1
2、September 1972, and is approved for use by the U.S. Army Armament, Munitions and Chemical Command, and is available for use by all Departments and Agencies of the Department of Defense. PAGE 2 Drawings Add: “9272315 - Chipboards, commercial 9328024 - Clip, packing, front 9328025 - Clip, packing rear
3、r1 PAGE 4 3.3.4 Pressure (Maximum Permissible Ind,vidual): Delete the parenthetical statement Il(115 percent of the upper pressure limit of the weapon)r1. PAGE 6 4.2.2.1, Half Increment; 4.2.2.2 Increments; and 4.2.2.3 Five . Increment Bundle; Delete: “Critical: 1. Incorrect Weight.Scale CD“ and sub
4、stitute: irlOO% Inspection Special (see para 6.6) 1. Incorrect Weight. . . . . . . .Scale CDrl c. AMSC NIA 1 of 3 - FSC 1376 - DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I
5、HS-,-,-MIL-1-48086 (AR) AMENDMENT 4 4.2.2.4, Propelling Charge Sub-Assembly (Front); and 4.2.2.5, Propelling Charge Sub-Assembly (Rear); Delete: llCr i t i cal : 1. Incorrect weight (weighing to be done immediately prior to assembling increments to shipping spindle.Scale CDg1 and substitute: tllOO%
6、Inspection Critical (applicable to any half increment, or five increment bundle missing). Special (see 6.6); (applicable to propelling charge sub- assembly out of weight tolerance). 1. Incorrect weight (weighing to be done immediately prior to assembling increments onto shipping spindle).Scale CDtt
7、PAGE 9 4.2.3.2.1, Delete tlCode Letter 1“ and subs.titute “code letter F“. PAGE 11 * 5.1.3: Delete in its entirety and substitute the following: 115.1.3 kvel C. The propelling charge sub-assembly (front) - Part No. 9276822 shall be inserted in packing clip (front) drawing 9328024 and then overpack 1
8、20 clips to a fiberboard carton conforming to the requirements of drawing 7548645 except that case liner shall conform to Type I, Grade A material of specification MIL-L-10547. The clips shall be arranged in 5 layers of 4 x 5 with clips lying flat. On one long side of carton, pack 1 layer 2 x 5 with
9、 clips standing on ends. On another end, pack 2 layers 1 x 4 plus 2 clips in another row with all clips standing on ends. Chipboard fillers, drawing 9272315 shall be added on sides and top as required to achieve a tight pack. The propelling charge sub-assembly (rear) - Part No. 9276823 shall be inse
10、rted in packing clip (rear) drawing 9328025 and then overpack 160 clips to fiberboard carton conforming to requirements of drawing 7548645 except that case liner shall conform to Type 1, Grade A material for specification MIL-L-70547. The clips shall be arranged in 7 layers of 4 x 5 with clips lying
11、 flat. On one long side, pack Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-I-4BOb (4) 13 7777906 043B4b O 9 MIL-1-48086 (AR) AMENDMENT 4 2 layers 2 x 5 with clips standing on ends. Chipboard fillers, drawing 9272315 shall be added on sides and
12、 top as required to achieve a tight pack. Kraft waxed paper will be placed between each layer. Add new paragraph as follows: n5.1.3.1 Alternative cartons. Use of existing cartons Nols 1, 3, and 4 Dwg. 7548645 is permissible when these cartons are available. All new procurements are to be made to the
13、 No. 2 design carton .It PAGE 13 Add new paragraph as follows: “6.6 Special defect. A defect, other than critical that judgement and experience indicates may, depending upon the degree of variance from the design requirement, result in hazardous or unsafe conditions for individuals using, maintainin
14、g or depending upon the product or could prevent performance of the tactical function of a major end item.“ The margins of this amendment are marked with an asterisk or vertical lines to indicate where changes (additions, modifications, corrections, deletions) from the previous interim amendment wer
15、e made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire . aontent irrespective of the marginal notations and relationship to the last previous amendment.“ C Cu s todi an : Army-AR Preparing activity: Army-AR (Project 1376 -A390 ) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
