1、MIL IT ARY SPECIFIC AT I MIL-T-62089E 27 May 1988 SUPERSEDING MIL-T-6208 9D 16 October 1984 N TRUCK, MAINTENANCE: WITH ROTATING HYDRAULIC DERRICK, AIR TRANSPORTABLE, DIESEL ENGINE DRIVEN, 39,500 POUNDS GVW, 6x4, COMMERCIAL This specification is approved for use by all Departments and Agencies of the
2、 Department of Defense. 1. SCOPE 1.1 Scope. This specification covers a diesel engine driven, six-wheel, four-rear wheel drive, 39,500 pounds gross vehicle weight (GVW), commercial truck equipped with a maintenance body and a hydraulically operated rotating and telescoping derrick with an insulated
3、pin-on jib or insulated telescopic section for mounting an aerial basket(s). Vehicles procured under this specification are commercial items which shall be warranted by the manufacturer as specified in acquisition documents. 2. APPLICABLE DOCUMENTS 2.1 Government documents. * 2.1.1 Specifications an
4、d standards. Unless otherwise specified, the following specifications and standards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in that issue of the Department of Defense Index of Specifications and
5、 Standards (DoDISS), and supplement thereto, cited in the solicitation. Beneficial comments (recommendations, addit ions, delet ions) and any pertinent data which may be of use in improving this document should be addressed to: US Army Tank-Automotive Command, ATTN: AMSTA-UED, Warren, MI 48397-5000,
6、 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this docqment or by letter. AMSC NIA IFzzEl DISTRIBUTION STATEMENT A. Approved for public release; distribution is un1 imited. ., , - THIS DOCUMENT CONTAINS (40 PAGES. Provided by IHSNot
7、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-% MIL-T-b2087E 23 7999906 0200549 3 E MIL-T-6 2 O8 9E . SPECIFICATIONS FEDERAL W-B-131 - Battery, Storage: Vehicular, Ignition, ZZ-T-381 Lighting and Starting. - Tires, Pneumatic, Vehicular (Highway). MILITARY MIL-P-514
8、- Plates , Ident if icat on Instruct ion and MIL-H-83282 - Hydraulic Fluid, Fire-Resistant, Marking , Blank. Synthetic Hydracarbon Base, Aircraft, NATO Code Number H-537. STANDARDS FEDERAL FED-STD-297 - Rustproofing of Commercial (Nontactical) Vehicles. STANDARDS MILITARY MIL-STD-1223 - Nontactical
9、Wheeled Vehicles Treatment, Painting , Ident if icat ion Marking and Data Plate Standards. * MIL-STD-1791 - Designing for Internal Aerial Delivery in Fixed Wing Aircraft. * MS51118 . - Pintle Assembly, Towing - 40,000 Lbs. Capacity, Manual Release. MSS1317 - Light, Warning, Vehicular, Rotating, D.C.
10、 * 2.1.2 Other Government documents. The following other Government documents form a part of this specification to the extent specified herein. Uniess otherwise specified, the issues shall be those in effect on the date of the solicitation. AFSC Design Handbook DH-1-11 - Air Transportability Handboo
11、k. (Application for copies of the AFSC Design Handbook should be addressed eo ASD/ENESS, Wright Patterson AFB, OH 45433.) DEPARTMENT OF TRANSPORTATION ( DOT) Federal Motor Carrier Safety Regulations. Federal Motor Vehicle Safety Standards. (Application for copies of DOT publications should be addres
12、sed to the Department of Transportation, Federal Highway Administration, Washington, D.C. 20591.) 2 8 a Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-T-b2089E 23 9999906 0200550 T MI L-T-6 2 O5 9 E ENVIRONMENTAL PROTECTION AGENCY ( EPA) Control
13、 of Air Pollution from New Motor Vehicles and New Motor Vehicle Engines. Noise Emission Standards for Transportation Equipment - Medium and Heavy Trucks. (Application for copies of EPA publications should reference the Code of Federal Regulations, 40 CFR, and the Federal Register and should be addre
14、ssed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSHA) Occupational Safety and Health Standards. 1926.556 - Aerial Lifts. (Application for copies of OSHA publicat ions should reference the Code of Federa
15、l Regulations, Title 29, and should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) (Copies of specifications , standards and other Government documents required by contractors in connection with specific acquisition functions should be obta
16、ined from the contracting activity or as directed by the contracting officer.) * 2.2 Other publications. The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DQD adopted shall be those listed in th
17、e issue of the DoDISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS shall be the issue of the non-Government document which is current on the date of the solfcitation. AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) ANSI A92.2 - American Nat
18、ional Standard for Vehicle-Mounted Elevating and Rotating Aerial Devices. (Application for copies of ANSI publications should be addressei the American National Standards Institute, Inc., 1430 Broadway, New York, NY 10018.) , to AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM Standards. ASTM
19、Designation: A120 - Pipe, Steel, Black and Hot-Dipped Zinc-Coated (Galvanized) Welded and Seamless, for Ordinary Uses (DoD adopted). B117 - Standard Method of Salt Spray (Fog) Testing (DoD adopted). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL
20、-T-62087E 23 W 7779706 0200553 3 = MIL-T-62089E (Application for copies of ASTM publications should be addressed to the American Society for Testing and Materiais, 1916 Race Street, Philadelphia, PA 19103.) SM, INC. SAE Standards and Recommended Practices 5318 - Air Brake Gladhand Service (Control)
21、and Emergency (Suppiy) Line - Couplers, Trucks, Truck-Tractors, and Trailers (DoD adopted). Size Engines (DoD adopted). 5350 - Spark Arrester Test Procedure for Medum 5537 - Storage Batteries. 5551 - Performance Levels and Methods of Measurement of.Electromagnetic Radiation from Vehicles and Devices
22、 (30-1000 MHz). for Truck-Trailer Jumper Cable, 5560 - Seven-Conductor Electrical Connector 5588 - Turn Signal Lamps. 5589 - Turn Signal Switch. 5682 - Rear Wheel Splash and Stone Throw 5688 5704 - Openings for Six- arid Eight-Bolt Truck Protection (DoD adopted). adopted). Transmission Mounted Power
23、 Take-offs (DoD adopted). - Truck Ability Prediction Procedure (Dod 5706 - Rating of Winches. 5844 - Nonmetallic Air Brake System Tubing (DoD 51067 - Seven-Conductor Jacketed Cable for Truck adopted). and Trailer Connectors. * J1113 - Electromagnetic Susceptibility Procedures for Vehicle Components
24、(Except Aircraft). 51292 - Automobile, Truck, Truck-Tractor, Trailer and Motor Coach Wiring. 51349 and Diesel. - Engine Power Test Code - Spark Ignition (Application for copies of SAJI publications should be addressed to SAE, Inc., 400 Commonwealth Drive, Warrendale, PA 15096.) THE TIRE AND RIM ASSO
25、CIATION, INC. Yearbook, 4 f I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-62087E 23 = 7799706 0200552 3 MIL-T-6 208 9E (Application for copies of Tire and Rim Association publications should be addressed to the Tire and Rim Association, Inc
26、., 3200 W. Market Street, Akron, OH 44313.) 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein (except for associated detail specifications, specif icat ion sheets or MS standards), the text of this specification shall take prec
27、edence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS * 3.1 Standard vehicle and accessories. Except as specified in 3.1.1 through 3.1.1.14, the vehicle, components, assemblies and accessories to
28、 be delivered under the contract shall be seandard or optional items, which meet or exceed the requirements of this specification. All chassis items shall be as represented and rated in the chassis manufacturers technical data and special bodies or mounted equipment shall be as represented and rated
29、 in the body and equipment manufacturers technical data. Technical data shall be limited to specifications and technical material, identical to that furnished to the authorized company representatives for selection of vehicle models and components, and shall be available to the engineering offices o
30、f the procuring activity prior to delivery of the items. The chassis model furnished shall be not older than the chassis manufacturers current model on the date of invitation for bids. When specified (see 6.2), a first article and a first article test shall be provided. 3.1.1 Special requirements. I
31、n addition to the standard vehicle and components specified in 3.1, the vehicle shall be furnished with special equipment as specified herein. * 3.1.1.1 Painting and marking. Treatment, painting, marking and data plates shall be in accordance with MIL-STD-1223. The exterior color and the identificat
32、ion markings shall be in accordance with the requirements of MIL-STD-1223 for the military service identified by the procuring activity (see 6.2). wound derrick components shall not be painted. When specified (see 6.2), concealed markings shall be furnished. Extruded, pultruded, molded or spiral 3.1
33、.1.1.1 Caution plates. Caution plates shall be furnished and mounted in conspicuous locations near the controls and in the drivers compartment. Caution plates shall conform to paragraph 4.10 of ANSI A92.2 and composition A (class 1 or 2) or composition C of MIL-P-514. At least the following informat
34、ion shall appear on the plates: 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-62087E 23 m 777770b 0200553 5 m MI L-T-62 O 9 E WAEtNING DERRICK MUST BE IN STOWED POSITION WHILE VEHICLE IS BEING MOVED. RATED BASKET LOAD, HYDRAULIC OUTRIGGERS
35、DOWN, NOT IN EXCESS OF POUNDS. INSPECT BASKET LEVELING SYSTEM. MAXIMUM VOLTAGE DERRICK AND BASKET WILL WITHSTAND VOLTS AC. OVERALL TRAVEL HEIGHT WHEN DERRICK IS IN STOWED POSITION VEHICLE SHALL NOT BE OPERATED IN WINDS IN EXCESS OF 30 MPH. BASKET LINER MUST BE INSTALLED WHEN OPERATING ON OR NEAR ELE
36、CTRICAL LINES. Do NOT PERMIT DIRECT CONTACT OF BASKET TO GROUND WHEN OPERATING ON OR NEAR ELECTRICAL LINES. WITH OUTRIGGERS PLACED FIRMLY ON THE GROUND, MAXIMUM SIDE SLOPES, DEGREES . MAXIMUM ASCENDING SLOPES, DEGREES . MAXIMUM DESCENDING SLOPES, DEGREES . WHEN USING PLASTIC NONCONDUCTIVE SECTION RE
37、MOVE THE METAL WINCH CABLE AND OTHER CONDUCTIVE ACCESSORIES. DO NOT DRILL HOLES IN BOOM OR BASKET TO DRAIN WATER, DUMP OUT WATER. AND BASKET(S), 3.1.1.1.2 Instruction plates. Plates showing schematics of all valves, valve controls, equipment, lubrication, and complete operating instructions for the
38、vehicle aerial equipment shall be fastened on the inside of one of the curbside vertical cabinet doors. Each control lever shall be marked with a plate depicting the function of the control. Individual marking shall be adjacent to each control. Plates and markings shall conform to composition A (cla
39、ss 1 or 2) or composition C of MIL-P-514. 3.1.1.1.3 Warning signs. Warning signs or labels as recommended ,by the Manufacturers of Aerial Devices and Digger Derricks Council shall be furnished and attached. 3.1.1.2 Rustproofing. When specified (see 6.2), the vehicle shall be rustproofed in accordanc
40、e with FED-STD-297. When specified (see 6.2), tropical rustproofing in accordance with FED-STD-297 shall be furnished. 3.1.1.3 Drain plugs. Drain plugs installed in the manual transmission and the rear axles for draining lubricants shall be of the permanent magnet type. 6 Provided by IHSNot for Resa
41、leNo reproduction or networking permitted without license from IHS-,-,-I - MIL-T-62089E 23 7999906 0200554 7 * MIL-T-6 208 9E 3.1.1.4 Wood treatment. Wood shall be treated in accordance with MIL-STD-1223. 3.1.1.5 Towing devices. Not less than two hooks, loops or pfns hooks, mounted to the chassis fr
42、ame or to rigid members which are attached to the frame, for towing the vehicle, shall be furnished. Towing devices shall be furnished at the rear of the vehicle. Towing devices shall be positioned so that the towing cable(s) will not deform other vehicular components. Towing devices may be utilized
43、 for the safety chain attachment devices specified in 3.1.1.6. * 3.1.1.6 Pintle assembly. A rotating pintle assembly in accordance with MS51118 shall be furnished and installed on the rear of the vehicle. The pintle assembly shall be installed on the vehicle chassis frame with reinforcements to tran
44、sfer a vertical tongue load of not less than 4,000 pounds and a horizontal drawbar load of not less than 40,000 pounds directly to the chassis rails. The rearmost portion of the pintle shall be forward, but not more than 4 inches forward, of the rearmost part of the vehicle. Two trailer safety chain
45、 attachment devices, one adjacent to each side of the pintle, shall be provided. Each attachment device shall provide an ultimate strength of not less than 40,000 pounds. The safety chain attachment devices shall be capable of accepting a standard grab hook (4-9/16 inches wide, 1-3/16 inches thick a
46、nd 25/32-inch throat width) for a 5/8-inch chain. chain attachments may be utilized for the rear towing devices (see 3.1.1.5). Safety 3.1.1.7 Lighting socket. A trailer lighting socket and cover assembly, conforming to SAE 5560, shall be furnished. The connector socket shall be mounted at a readily
47、accessible location on the rear of the vehicle, near the pintle. 3.1.1.8 Trailer lighting cable. A coiled trailer lighting cable, conforming to SAE 51067, shall be furnished. The lighting cable shall be not less than 10 feet long when fully extended. Both ends of the cable shall be equipped with a r
48、ound plug conforming to SAE 5560. The plugs shall be equipped with a grip for withdrawing from the connector sockets. The cable shall be packaged and stowed in the vehicle tool compartment. 3.1.1.9 Electric trailer brake controller. The vehicle shall be provided with an electric brake controller. Th
49、e controller shall be installed in the truck cab and wired through the SAE 5560 12-volt socket. The controller shall operate on the 12-volt electrical system of the vehicle and shall include load control, hand or foot lever, and controller for synchronizing the electric brakes and brake lights of the trailer with the truck brakes. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-T-b208
